Extron electronics RWM 1 User manual

RWM 1 • Installation Guide
Overview
The RWM 1 is an accessory kit for the TLP Pro 525M touchpanel to be installed into a wall. This guide provides
instructions for experienced and professional installers to mount and install the TLP Pro 525M using RWM 1.
Attention
• All structural steps and electrical installation must be performed by qualified personnel in accordance with local
and national building codes and electrical codes.
• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualifié, conformément aux
codes du bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
Figure 1. RWM 1
1
AScrews to turn locking arm (4) C 2-gang EU junction box adaptation E 1-gang North America junction
box adaptation, horizontally mounted
B Magnets (4) D 1-gang MK junction box adaptation F Locking arms (4)
The RWM 1 ships with three magnets attached to the front and a spare magnet (G) attached to the back, as shown in
Figure 1. The spare magnet can be moved to the front if extra support is needed.
TOP
NORTH
AMERICA
EU
MK
EU
NORTH
AMERICA
EU
MK
EU
Front View Back View
FF
BB
C
C
D
D
EE
AA
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
www.extron.com

RWM 1 • Installation Guide (Continued)
Figure 3. Installing a TLP Pro 525M with RWM 1
Before You Start
Decide where you want to mount the touchpanel. A cut-out template for the RWM 1 is available at www.extron.com and
provides clearances for the components to be installed.
1. Use the template to cut a hole in the drywall (Figure 2, 1) that is 4.42” H x 6.38” W (112 mm H x 162 mm W).
The RWM 1 is suitable for drywall that is 1/2-1’’ thick.
2. Route cables to the hole.
If local building codes require cables to be run through a conduit to a junction box, then the RWM 1 can be used with a
standard 2-gang EU junction box, 1-gang MK junction box, or a horizontally mounted 1-gang US junction box (Extron JB
125). The junction box must be purchased separately.
• If required, attach the junction box to the RWM 1 using the screws provided with the junction box through the
corresponding holes in the RWM 1(see Figure 1).
268-3269-01 Rev.B
11 18
© 2018 Extron Electronics. All rights reserved. www.extron.com
Mounting the RWM 1 to Drywall
1. Ensure the locking arms (2) are lying flat against the top and
bottom of the RWM 1, and insert it into the hole.
2. Use a Philips-head screwdriver to turn and tighten the locking
arms against the drywall. The locking arms should hold the RWM
1 securely, but should not be overtighten.
11
RWM 1
22
e
33
5
5
RWM 1
Touchpanel
Mounting
Plate
Lock Screw
Back View
TLP Pr
o 525M
66
44
Figure 2. Installing RWM 1 into the wall
Mounting the TLP Pro 525M
1. Run a PoE/Ethernet cable through the RWM 1 and
connect it to the rear panel port on the touchpanel
(see the TLP Pro 525, 725, and 1025 Series User
Guide)
2. The touchpanel mounting plate has two hooks (3)
located on the top left and right corners. Position
the TLP Pro 525M so the hooks fit into the touch-
panel’s two rear slots (see the TLP Pro 525 Series,
725 Series, and 1025 Series User Guide).
3. Slide the TLP Pro 525M down slightly so the hooks
are secure in the slots.
4. The tongue at the bottom of the mounting plate
(4) sits in the groove at the bottom of the touch-
panel (5). Fasten the touchpanel to the mounting
plate by tightening the lock screw (6).
5. Place the touchpanel against the RWM 1. Strong
magnets on the RWM 1 hold the touchpanel in
place.