AXIOMTEK GOT315WL-845-PCT User manual

GOT315WL-845-PCT
All-in-One
15.6” WXGA TFT Fanless
PCT Multi-Touch PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, or any liability arising from such uses.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update any information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any
forms or by any means, electronic, mechanical, photocopying, recording, among others,
without prior written permission from Axiomtek Co., Ltd.
CAUTION
Wrong type of batteries may cause explosion. It is recommended that users only replace with
the same or equivalent type of batteries as suggested by the manufacturer once properly
disposing of any used ones.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
June 2018, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. Be sure to ground yourself to prevent static charge when installing any internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cord from the GOT315WL-845-PCT series prior to any installation.
Be sure both the system and all external devices are turned off. Sudden surge of power
could ruin sensitive components. Make sure the GOT315WL-845-PCT Series is properly
grounded.
3. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on human body.
When handling boards and components, wear a grounding wrist strap available
from most electronic component stores.
Trademark Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel®and Pentium®are registered trademarks of Intel Corporation.
Windows 10, Windows 10 IoT Enterprise, Windows 8.1, Windows 8, Windows 7, are
trademarks of Microsoft Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Section 1 Introduction............................................. 1
1.1 General Descriptions..........................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions and Outlines ...................................................................4
1.4 I/O Outlets............................................................................................6
1.5 Packing List.........................................................................................7
Section 2 Hardware and Installation ...................... 9
2.1 Board Layout.......................................................................................9
2.2 Jumper and Connector Settings......................................................10
2.2.1 ‘Auto Power On’Jumper (JP3).................................................................. 10
2.2.2 ‘Restore BIOS Optimal Defaults’Jumper (JP6)........................................ 10
2.2.3 COM Port Connector..................................................................................11
2.3 Ethernet Connector...........................................................................11
2.4 Mounting Methods ............................................................................12
2.5 Hardware Installation........................................................................14
2.5.1 Installing a HDD ........................................................................................ 14
2.5.2 Installing a DRAM...................................................................................... 16
2.5.3 Installing a Wireless LAN Card ................................................................. 17
2.5.4 Connecting the Power Input...................................................................... 19
Section 3 AMI BIOS Setup Utility .......................... 21
3.1 Navigation Keys ................................................................................21
3.2 Main Menu..........................................................................................22
3.3 Advanced Menu.................................................................................23
3.3.1 NCT6106D Super IO Configuration................................................................... 24
3.3.2 Hardware Monitor.............................................................................................. 25
3.3.3 ACPI Settings .................................................................................................... 26
3.3.4 CPU Configuration............................................................................................. 27
3.3.5 SATA Configuration............................................................................................ 28
3.3.6 USB Configuration............................................................................................. 29
3.3.7 Utility Configuration ........................................................................................... 29
3.3.8 PCIE/mSATA Mini Card Configuration............................................................... 30
3.4 Chipset Menu.....................................................................................31

v
3.4.1 North Bridge....................................................................................................... 31
3.4.2 South Bridge...................................................................................................... 32
3.5 Security Menu....................................................................................33
3.6 Boot Menu..........................................................................................34
3.7 Save & Exit Menu ..............................................................................35
Section 4 Driver and Installation ......................... 37
4.1 Operating System .............................................................................37
4.1.1 Installing System Drivers........................................................................... 37
4.2 Touch Screen.....................................................................................38

vi
This page is intentionally left blank.

GOT315WL-845-PCT User’s Manual
Introduction 1
Section 1
Introduction
This Section contains general information and detailed specifications of the
GOT315WL-845-PCT, including the following subsections:
Figure 1-1 Front panel of the GOT315WL-845-PCT
General Descriptions
Specifications
Dimensions and Outlines
I/O Outlets
Packing List
1.1 General Descriptions
The GOT315WL-845-PCT adopts a 15.6-inch WXGA TFT LCD with 400-nit brightness and an
Intel® Pentium® Processor N3710 (2M Cache, up to 2.56 GHz), providing excellent computing
performance and thermal resistance. This fanless platform is especially designed for operation
under a harsh environment including steel refinery, oil pipe, ship, machine maker, and many
more. Having abilities below surely makes GOT315WL-845-PCT a most robust and
cost-effective solution.
Design for extended operating temperature range and ingress protection
The GOT315WL-845-PCT is featured by a technology to sustain extended operating
temperature range between 0°C and +50°C by incorporating compact ID and fanless cooling
system with a low power Intel® Pentium® Processor N3710 (2M Cache, up to 2.56 GHz). It
also adopts an IP65 front bezel to protect itself from liquid and dust. These designs help make
the system a power-efficient solution.
Reliable and stable design
The GOT315WL-845-PCT is specially designed for vibration-prone environments, best for
the transportation (vehicle, railway, marine) and industrial machinery markets. To suit the need
of high capacity storage, the GOT315WL-845-PCT can work in operation mode under 1.0G
(10 ~ 500Hz) with a patent of anti-vibration design. The design behind the patent has improved
the system reliability and sustainability. (Note: Sometimes heavy-vibration may cause the LCD
screen to flash in white color; however, it won’t affect the function of the product.)

GOT315WL-845-PCT User’s Manual
2 Introduction
WLAN antenna supported (optional)
The GOT315WL-845-PCT comes with 2 PCI Express Mini Card slots as an add-on option to
connect a wireless LAN card under 802.11 a/b/g/n protocols, or with other 3G/GPRS
applications, etc. These slots also come with 3 optional fixed rotational WLAN/3G antennas for
wireless network connection.
Multi-Touch PCAP touch with 7H surface hardness
The GOT315WL-845-PCT is designed with a user friendly multi- PCAP touch. Users can
operation it with direct touch. The surface hardness is up to 7H, good for applications of
anti-scratch purpose.
Other features
The GOT315WL-845-PCT utilizes one 204-pin DDR3L SODIMM system memory up to 8GB at
the maximum, one SATAHDD and one mSATA. It provides an over-current protection-fuse and
a full set of I/O including RS-232/422/485, USB 2.0, USB 3.0, audio (line-out), and Gigabit
Ethernet. Additionally, this slim unit supports panel mount as the standard installation, as well
as optionally wall mount, VESA mount and desktop stand mount.
1.2 Specifications
Main CPU Board
CPU
Intel® Pentium® Processor N3710 (2M Cache, up to 2.56 GHz) onboard
System Memory
1 x 204-pin DDR3L SO-DIMM socket
Maximum memory up to 8GB
BIOS
AMI UEFI BIOS
I/O System
Standard I/O
2 x RS-232/422/485
2 x USB 2.0
2 x USB 3.0
Ethernet
2 x RJ45 for Gigabit Ethernet (Intel i211AT)
Audio
1x Line-out
Expansion
1 x Mini-card slot (w/SIM slot)
1 x Mini-card slot (supports mSATA)
Storage
1 x 2.5” SATA
1 x mSATA

GOT315WL-845-PCT User’s Manual
Introduction 3
Power connector
Phoenix power connector or screw power connector
System Specifications
15.6”WXGA (1366x768) LCD with LED backlight
Multi- PCAP touch
A design of fanless heat dispensation
IP65 aluminum front bezel
Disk drive housing:
One 2.5” SATA drive
Net weight
4.5 Kgs
Dimensions (of the main body)
396.81 x 247.12 x 59 mm
Operating temperatures
0°C to 50°C
Relative humidity
20% to 90% @ 40°C, Non-condensing
System power input
DC power input : 24VDC with Phoenix power connector
AC power input : 12VDC/5A, 60W power adapter
NOTE: All specifications and images are subject to change without notice.
The performance of the system might be adversely affected at an operating
temperature above 40°C.

GOT315WL-845-PCT User’s Manual
4 Introduction
1.3 Dimensions and Outlines
Diagram 1-1 shows the dimensions and outlines of the front panel of the GOT315WL-845-PCT
Diagram 1-1 Front dimensions and outline of the GOT315WL-845-PCT
Front dimensions: 396.81 x 247.12 x 59 mm

GOT315WL-845-PCT User’s Manual
Introduction 5
Diagram 1-2 Back outline of the GOT315WL-845-PCT
Diagram 1-3 Cutting-out dimensions of the GOT315WL-845-PCT
Cut out dimensions: 386.6 x 236.9 mm
NOTE: The limited of wall depth is 9 mm in panel mount.

GOT315WL-845-PCT User’s Manual
6 Introduction
1.4 I/O Outlets
Please refer to Figures 1-2 and 1-3 for I/O locations of the GOT315WL-845-PCT.
Figure 1-2 Bottom view of the GOT315WL-845-PCT
Figure 1-3 Side view of the GOT315WL-845-PCT

GOT315WL-845-PCT User’s Manual
Introduction 7
1.5 Packing List
A complete bundled package should contain the following items:
GOT315WL-845-PCT unit x 1
Driver disc x1 (various OS versions and bundles available)
Phoenix connector x 1 (DC power version only)
Power Adapter & power cord (AC adapter version only)
Panel mount kit x 12
Screws for HDD x 2
SATA data cable x 1
SATA power cable x 1
Please contact an Axiomtek distributor immediately if any of the above-mentioned items is
missing.

GOT315WL-845-PCT User’s Manual
8 Introduction
This page is intentionally left blank.

GOT315WL-845-PCT User’s Manual
Hardware and Installation 9
Section 2
Hardware and Installation
The GOT315WL-845-PCT provides rich I/O ports and flexible expansion for users to meet
different demands; for example, in a case of CF card expansion. This Section describes
hardware installation, including the following subsections:
Board Layout
Jumper and Connector Setting
Mounting Methods
Hardware Installation
Power Input
2.1 Board Layout
Please follow the steps below to open the GOT315WL-845-PCT unit.
Step 1 Unscrew 8 screws (see red circles in Figure 2-1) on the back cover.
Figure 2-1 Back cover
Step 2 Remove the back cover.
Figure 2-2 Board layout

GOT315WL-845-PCT User’s Manual
10 Hardware and Installation
2.2 Jumper and Connector Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close the pins. And remove jumper clip from 2 jumper pins to open the pins.
Diagram 2-1 illustrates how to set up a jumper.
Diagram 2-1 Definitions of pin settings
Pins 1-2 open Pins 1-2 close Pins 1-2 close All pins open
Before applying power to GOT315WL-845-PCT, please make sure all of the jumpers and
connectors are in default position as listed in Table 2-1.
Table 2-1 Factory mode of jumper settings
Jumper
Descriptions
Setting
JP3
Auto Power On
Default: Disable
2-3 close
JP6
Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation
1-2 close
2.2.1 ‘Auto Power On’Jumper (JP3)
There are two ways to set up auto power on function. One is jumper setting, the other one is
switch setting. One of them is setting byAT that system will be AT mode.
If JP3 is enabled for power input, the system will be automatically power on without pressing
soft power button. If JP3 is disabled for power input, it is necessary to manually press soft
power button to power on the system (see Table 2-2).
Table 2-2 JP3 setting
(Default)
2.2.2 ‘Restore BIOS Optimal Defaults’Jumper (JP6)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this procedure
can restore BIOS optimal defaults (see Table 2-3).
Table 2-3 JP6 setting
(Default)
Function
Setting
Disable auto power on (Default)
1-2 close
Enable auto power on
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close

GOT315WL-845-PCT User’s Manual
Hardware and Installation 11
2.2.3 COM Port Connector
The pin assignment for RS-232/ 422/ 485 is listed In Table 2-4.
Table 2-4 Pin assignment for RS-232/ 422/ 485
2.3 Ethernet Connector
There are two RJ-45 connectors, LAN1 and LAN2, inside the GOT315WL-845-PCT. Ethernet
connection can be established by plugging one end of the Ethernet cable into this RJ-45
connector and the other end (phone jack) to a 1000/100/10-Base-T hub.
Please refer to Table 2-5 for detailed pin assignment for LAN1 and LAN2.
Table 2-5 Pin assignment for LAN1/ LAN2
Pin
Signal
Pin
Signal
L1
MDI0+
L5
MDI2+
L2
MDI0-
L6
MDI2-
L3
MDI1+
L7
MDI3+
L4
MDI1-
L8
MDI3-
A
Active LED (Yellow)
B
100 LAN LED (Green) / 1000 LAN LED
(Orange)
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT315WL-845-PCT User’s Manual
12 Hardware and Installation
2.4 Mounting Methods
There are four ways to install the GOT315WL-845-PCT, namely: panel/ VESA/ wall/ desktop
mount.
The GOT315WL-845-PCT provides a standard panel mount kit. It can be installed by way of
panel mount (see Figure 2-1, 2-2).
Figure 2-1 Panel mount (back chassis)
Figure 2-2 Panel mount kit

GOT315WL-845-PCT User’s Manual
Hardware and Installation 13
Alternatively, the GOT315WL-845-PCT can be installed by way of VESA mount which is in the
dimensions of 100x100 mm. Simply fix four screws to fasten the kit from the back chassis, as
shown in Diagram 2-3. Additionally, users can otherwise go for wall mount as an option, as
shown in Diagram2-4.
Diagram 2-3 VESA mount (back chassis)
Diagram 2-4 Wall mount (back chassis)

GOT315WL-845-PCT User’s Manual
14 Hardware and Installation
2.5 Hardware Installation
2.5.1 Installing a HDD
The GOT315WL-845-PCT provides a convenient Hard Disk Drive (HDD) bracket for users to
install a 2.5” SATA HDD. Please follow the steps:
Step 1 Refer to Section 2.1 to open the back cover and dissemble the HDD tray by
un-screwing the 2 screws (as shown in the red circles in Figure 2-5).
Figure 2-5 Separating the bracket from the HDD tray
Step 2 Fasten a HDD from the back side of the bracket with two screws (see Figure
2-6).
Figure 2-6 Fastening a HDD to the bracket
Front: Back: