Technicolor TCA203 User manual

Home System Installation
Guide
Technicolor TCA203
Release Hawaii 5.1 SU1
Drawing number TCA203Install issued 12/19/2012

2
Copyright © 2013 iControl Networks All rights reserved.
No reproduction in whole or in part without prior written approval. iControl Networks, iControl, and
iControl logo design are pending trademarks of iControl Networks. All other trademarks are the property
of their respective owners. Information contained herein is subject to change without notice. The only
warranties for iControl products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. iControl Networks shall not be liable for technical or editorial errors or omissions
contained herein. All rights reserved.
Audience
This guide is intended for people who want to use the Subscriber Portal to access their TouchScreen
settings and monitor their location.
Typographic Conventions
This document uses the following typographic conventions to help you locate and identify information:
Italic text Identifies new terms, emphasis, and book titles
Bold text Identifies button names and other items that you can click or touch in the graphical
user interface or press on a computer keyboard
Note: Notes provide extra information about a topic that is good to know but not essential to the
process.
IMPORTANT: Important items draw your attention to actions that could compromise the security
of your system or result in the loss of data.
Home System Installation Guide

Overview
3
Overview
To set up the security system in a customer premises:
1. Complete a Home Security Survey (HSS) for the customer.
2. Ensure the customer premise has access to the Internet.
3. Activate the TouchScreen (see Installing the Security System on page 5).
The TouchScreen can connect to the managed router/modem either wirelessly or by Ethernet cable. The
TouchScreen communicates with sensors by radio frequency. Optional cameras communicate with the
security network router wirelessly. The TouchScreen maintains communication with the system servers
through the Internet and by Cellular.
The security network router MUST be installed “in front” of all other home networks relative to the
Internet. Connect the customer’s home network to the Internet through the security network router by
Ethernet cable as described on pages 15 and 17. The customer can install a retail router behind the
security network router and access the Internet. The customer can choose to expose their retail router to
the Internet through the DMZ of the security network router as described in the TouchScreen User
Guide.
A MAXIMUM of six IP cameras and 47 ZigBee devices are supported for the system. ZigBee devices
consist of anything that communicates with the TouchScreen over radio frequency, such as
door/window sensors, lighting devices, thermostats, panel interface devices, key pads, and key fobs and
smoke detectors.
Figure 1: Home Security Configuration

4
Installation Tools
The following are the tools required to install the security system:
Digital multi-meter
Rubbing alcohol with container to dilute with
water
Paper towels
Drop cloth for work area
Ladder 6’
Compressed air and soft-bristled brush
Assorted screwdrivers
Sound sensor tester for testing glass break
sensors
Aerosol smoke tester
Double-sided sticky tape
Alternative double-sided sticky tape
Tape measure
Pocket level
Multi-purpose scissors
Flashlight
Shoe covers
Ethernet cable of sufficient length
(used to configure the camera or
if the TouchScreen will not connect to the
router/modem wirelessly)
Home System Installation Guide

Installing the Security System
5
Installing the Security System
Installing the security system in the customer’s home consists of the following general processes. These
processes are detailed in the following pages of this section:
A. Setting up the Router (page 6)
B. Installing the TouchScreen (page 7)
C. Ensure your TouchScreen Configuration Information is Correct (page 12)
D. Activating the System (page 14)
E. Adding Panel Interfaces (page 24)
F. Adding Sensors (page 28)
G. Adding Cameras (page 38)
H. Adding Lighting Devices (page 47)
I. Adding Thermostats (page 50)
J. Adding Key Fobs (page 53)
K. Adding Key Pads (page 57)
L. Adding Sirens (page 61)
M. Testing the Alarm Functionality of the Security System (page 65)
N. Setting and Validating the Security Information (page 69)
O. Mounting the Sensors (page 74)
P. Configuring the TouchScreen (page 75)
Q. Activating the Subscriber Portal (page 74)

6
Step A: Setting up the Router
1. Ensure the customer premises has access to the Internet.
2. Reset the home network router.
Note: Do this, also, if you are restarting the installation process after having established the
connection between the TouchScreen and the router.
Home System Installation Guide

Installing the Security System
7
Step B: Installing the Technicolor TouchScreen
1. Remove the TouchScreen from its packaging.
2. Use a P1 Phillips screwdriver to remove the (1) screw from the battery cover of the TouchScreen,
and detach the cover.
3. Unwrap the 4.0 volt battery from its packaging and install it in the battery compartment.
Warning: The rechargeable battery that came with your TouchScreen is only available through
your service operator. If your battery needs to be replaced, contact your service operator to
arrange for replacement.
4. Position the battery and cables inside the battery compartment so the cables lie along the top of
the battery.
5. Align and connect the battery’s pins to the battery connector so that the wire order is (top-to-
bottom) BLACK, BLACK, WHITE, RED, RED.

8
6. Replace the battery cover and the screw.
7. Place the AC power cable through the holes on the sides of the TouchScreen stand.
8. Connect the adapter cable to the back of the TouchScreen.
Home System Installation Guide

Installing the Security System
9
9. Connect the stand to the back of the TouchScreen. Insert the longest peg into the Tamper Switch
hole, which is the top right hole on the back of the TouchScreen. Slide the stand downward until
the pegs lock in place.
10. Position the TouchScreen near an un-switched wall outlet (not controlled by a light switch).
11. If the installation plan does not involve the TouchScreen connecting to the customer’s network
wirelessly, then connect an Ethernet cable to the TouchScreen and the iControl-dedicated router.
12. Insert the AC adapter into the bracket as shown.

10
Table 1: AC
Power Supply
Ratings
Rating Value
Voltage 100 -
120V
Current 0.5A
Frequency 60 Hz
13. Remove the center screw from the wall outlet.
14. Plug the TouchScreen’s AC adapter into the TOP plug of the wall outlet, and replace the center
screw through the bracket hole.
After a few seconds, the Installation Welcome screen is displayed on the TouchScreen.
Home System Installation Guide

Installing the Security System
11
Figure 2: Activation: Installation Welcome Screen
Note: If the TouchScreen does not display the Installation Welcome screen, you must reset it to
factory default (see page 88).

12
Step C: Ensure Your TouchScreen Configuration Information Is Correct
1. Ensure you have the following information from Customer Care:
Activation Code
Broadband Server IP
Cellular Server IP
Cellular APN
Deployment to which the TouchScreen, based on CPE ID, is applied in Inventory
(only if your system uses deployments)
2. On the TouchScreen, tap System Information.
The System Information screen is displayed.
Figure 3: Installation: System Information Screen
3. Tap directly on the Broadband Server value (the IP).
The Edit System Configuration Information screen is displayed.
4. Tap the Broadband Server IP, Cellular Server IP, and the Cellular APN value to change them. When
you tap them, a keyboard screen is displayed. Enter the new values and tap Done.
5. After all the values have been set, tap Next.
The System Information screen is displayed.
6. Tap Next.
The Welcome screen is displayed.
Home System Installation Guide

Installing the Security System
13
Figure 4: Welcome to Product Activation Screen

14
Step D: Activating the System
Note: To set the language used in the TouchScreen, tap Change Language and choose the
preferred language.
1. Tap Next.
The Connectivity Setup screen displays the type of Internet routers and cable gateways to
which the TouchScreen can connect.
Figure 5: Connectivity: Connectivity Setup Screen
Note: The routers and gateways displayed on the screen may vary.
The activation process supports the following routers and gateways:
Netgear WNR1000v2
SMC D3GN-RRR (Wi-Fi connection only)
SMC D3GNV-NCS, -IMS
Note: If WPSis supported on the router, it is disabled during the activation process.
2. Tap the type of router the TouchScreen will connect to, and tap Next.
The Connectivity Setup screen displays options for connecting to the router/modem.
Home System Installation Guide

Installing the Security System
15
Figure 6: Connectivity: Connectivity Setup Screen Router/Modem Options
The following options are displayed:
Wi-Fi - TouchScreen connects to the router/modem wirelessly. If you select this
option, follow the procedures described in For Wireless TouchScreen-to-Router Con-
nectivity.
Ethernet - TouchScreen connects to the router/modem using an
Ethernet cable. If you select this option, follow the procedures described in For Cabled
TouchScreen-to-Router Connectivity.
For Wireless TouchScreen-to-Router Connectivity
Figure 7: Activation: Initial Router Configuration, Wireless Router-to-TouchScreen
1. Tap Wi-Fi and then tap Next.
The Router Connection Checklist is displayed.

16
Figure 8: Activation: Router Connection Checklist Screen
2. Follow the instructions on the Router Connection Checklist screen.
3. Tap Next.
The TouchScreen locates all the available wireless routers in range, and displays their MAC
addresses.
Figure 9: Activation: Setting Up for Wi-Fi Screen
Figure 10: Activation: Router Located Screen
4. Check the MAC address for the router/modem to which the TouchScreen must connect (usually
located at the back of the device).
5. Tap the MAC address for the correct router.
6. Tap Next.
The Configuring and Securing the Router screen is displayed as the TouchScreen establishes a
firm connection with the router/modem, the Broadband servers, and the Cellular connectivity
servers.
Home System Installation Guide

Installing the Security System
17
Figure 11: Activation: Configuring and Securing Router Screen
Continue to "Completing Activation" on page 19
For Cabled TouchScreen-to-Router Connectivity
Figure 12: Activation: Initial Router Configuration, Ethernet Router-to-TouchScreen
1. Tap Ethernet with Router and then tap Next.
The Ethernet Connection Checklist is displayed.

18
Figure 13: Activation: Ethernet Connection Checklist Screen
2. Follow the instructions on the Ethernet Connection Checklist screen.
3. Tap Next.
The Ethernet Adapters screen is displayed. The TouchScreen locates and secures the Ethernet
adapter.
Figure 14: Activation: Ethernet Adapters Screen
4. Wait a few minutes for the router/modem to configure and secure the network.
Note: If the system cannot find the proper router, ensure it has been reset to factory
default.
The Configuring and Securing the Router screen is displayed as the TouchScreen establishes a
firm connection with the router/modem, the Broadband servers, and the Cellular connectivity
servers.
Home System Installation Guide

Installing the Security System
19
Figure 15: Activation: Configuring and Securing Router Scree
5. Tap Next and continue to Completing Activation.
Completing Activation
The Wi-Fi and Cellular Strength screen displays the relative strength of the TouchScreen’s connection to
the router/modem and a GPRS/EDGE receiver.
Figure 16: Activation: Wi-Fi and Cellular Signal Screen
Note: If the router is connected to the TouchScreen by Ethernet, then Wi-Fi is not tested.
1. Tap Next.
The Testing Connectivity screen is displayed.

20
Figure 17: Activation: Testing Connectivity Screen
2. Tap Next.
The TouchScreen tests its connectivity with the Broadband servers and the Cellular servers, which
is used for alarms and alerts when the broadband connection is unavailable.
3. Figure 18: Activation: Testing Connectivity Complete Screen
Note: This only tests the TouchScreen’s ability to connect by broadband and cellular. It does
not determine whether the TouchScreen is actually connected to the servers over
broadband and cellular.
4. When the connectivity test is successful for each, tap Next.
The TouchScreen checks for a newer firmware version to install.
Home System Installation Guide