TECshow FRESNELED 3100 MAX User manual

PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE /
POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR
USER MANUAL / MANUAL DE USUARIO
FRESNELED
MAX

FRESNELED MAX
P.
2
1. OVERVIEW
Fresneled 3100 MAX is a Fresnel LED powered by 1 250W
COB LED that works at 3100K and has a performance 50%
greater than the MKII version, which has an output similar
to the classic 2000W halogen fresnels. In addition to hav-
ing a 90Ra color reproduction, the fixture is equipped with
a zoom function that allows to vary its beam angle between
15º and 60º, adding great versatility to any fresnel applica-
tion. Thanks to its COB LED, Fresneled 3100 MAX enables
a great energy saving and a very low heat generation, impor-
tant attributes for both theater and broadcasting. Finally, its
16-bit dimmer with four dimming curves, strobe effect and
selectable refresh rate, which guarantees flicker-free oper-
ation, are some of its most remarkable features.
SPECIFICATIONS
Source & Optic
• Light Source: 1 250W COB LED
• Color temperature: 3200K
• LEDs life: 50,000 hours
• Zoom: 15º-60º linear zoom
• Selectable refresh rate: 600Hz, 1200Hz, 2000Hz,
4000Hz & 25000Hz
Photometric Data
• Luminous Flux:
• 15º: 5416 lm
• 60º: 10519 lm
• Color rendering: >90Ra
• Flux: 15º: 4000 Lux @ 5M (16 ft.)
• Flux: 60º: 404 Lux @ 5M (16 ft.)
Effects & Functions
• Dimmer: Full range 0-100% (16-bit)
• 4 dimming curves
• Strobe effect: 0-20 flashes per second
• 15º-60º Electronic zoom
• Flicker free
Control
• DMX channels: 1/2/3
• Operational modes: DMX, Static, Master/Slave
& On-board control
• RDM Function
Electrical
• Input voltage range: AC100–240V, 50-60Hz
• Power consumption: 180W
Physical
• LED display
• DMX connectors: 4 XLR connectors (XLR-3 In
and Out; XLR-5 In and Out)
• Power supply connectors: PowerCON® In/Out
• Cooling: Forced convection
• Dimensions: 417x286x260 mm. / 16.5x11x10 in.
• Weight: 6.6 Kg. / 14.5 Lbs.
ENGLISH VERSION

FRESNELED MAX
P.
3
2. SAFETY WARNING
• This product must be installed by a qualified pro-
fessional ONLY.
• All maintenance must be carried out by a qualified
electrician ONLY.
• All minimum distance of 0.5m must be maintained
between the equipment and a combustible surface.
• The product must always be operated in a well
ventilated area.
• DO NOT stare directly into the LED light source.
• Always disconnect the power before carrying out
any maintenance.
• The earth must always be connected to the ground
• Ensure that all parts of the equipment are kept
clean and free of dust.
• A minimum distance of 0.8m must be maintained
between the light and projecting surface.
ENGLISH VERSION

FRESNELED MAX
P.
4
ENGLISH VERSION
3. INSTALLATION
The LED fixture can be mounted in a hanging position using
the supporting bracket. The bracket should be secured to the
mounting truss or structure using a standard mounting clamp.
Please note that when hanging the unit a safety cable should
also be used.
Hanging
MOUNTING-
POWER CONNECTIONS
220-240V: 10 UNITS may be connected in series
110-120V: 5 UNITS may be connected in series

FRESNELED MAX
P.
5
ENGLISH VERSION
4. DISPLAY PANEL OPERATION
MENU: Return to the previous menu
ENTER: Enter the currently selected menu.
UP: Scroll down through the current menu list or decrease the
value of the current function.
DOWN: Scroll up through the current menu list or increase the
value of the current function.
DISPLAY OPERATION
QUICK-ACCESS KEYS
MENU: By press and holding the MENU key when at the
main menu it is possible to directly access the DIM function.
CONTROL KNOB
• DIMMER
• ZOOM
NOTES:
• Press the adjusting button (any one) twice, the fix-
ture will be in STAT mode;
• Press the DIMMER button, DIM shows in the menu,
the value range is 0-100%;
• Press ZOOM button, value range 0-100% appears.

FRESNELED MAX
P.
6
ENGLISH VERSION
MENU MAP

FRESNELED MAX
P.
7
ENGLISH VERSION
DIMMER (STAT)
• DIM: To adjust level of intensity
• ZOOM: To adjust the zoom position.
NOTES:
• When using this function, if the MCON menu is set
as MAST, then the fixture will transfer the DIM val-
ues to other fixtures.
• When DMX data is received at the fixture, it will
automatically return to main menu after 2 minutes
of no key operation.
RUN MODE
• RUN: This menu allows the user to select the op-
erating mode of the fixture. Select DMX for nor-
mal DMX operation or SLAV for slave operation.
DMX ADDRESS
• ADDR: This menu allows the user to select the
startaddressofthefixture.Use<UP>or<DOWN>
keys to select required start address.
MOTOR RESET (MOTR)
• Press ENTER to enter <MOTR>
• Press UP/DOWN and select <YES> or <NO>
• When you select <YES> and press ENTER, the
motor will be reset to origin.
• When you select <NO>, and press ENTER, no control.

FRESNELED MAX
P.
8
ENGLISH VERSION
• SET: This menu allows the user to adjust key op-
eration settings for this fixture. KEY: Select <ON>
for automatic lock-out. Password to re-enter the
display is <UP>+<DOWN>+<UP>+<DOWN>.
• Select <DIM1>, <DIM2>, <DIM3> or <DIM4>
for different dimming speeds. <DIM4> is the slow-
est dimming speed).
• CURV: allows the user to adjust the shape of the
dimming curve. See the CURV chart to under-
stand more about actual dimming curves.
• In order to reset custom modes to default values
select <REST>.
• PERS this setting allows the user to select the
DMX personality of the fixture. Refer to DMX per-
sonality charts for specific details.
• SLCK is used to lock the settings menu. When
SLCK is set to <ON> then user must insert pass-
code (UP+DOWN+UP+DOWN) in order to ac-
cess the settings menu.
• DERR Chosose <SAVE> in order to save the last
DMX data incase of DMX signal error. Choose
<BLACK> in order to blackout in case of DMX signal error.
• <ZOOM> is for setting zoom, press UP/DOWN to
select. <BASE> is standard setting; <POS1> is
zoom setting 1; <POS2> is zoom setting 2. Press
MENUtogetback,andtheSettingis savedautomatically.
• PERF: this setting allows the user to select the
performance characteristics of the fixture.
• MCON: This function allows the user to select
whether the fixture will send DMX data to other
fixturesduringstand-aloneoperation.The<MAST>
setting allows data to be sent to Other fixtures.
The<SELF>settingisdefaultandwillnotsendDMX
data to other fixtures.
SPECIAL SETTINGS

FRESNELED MAX
P.
9
ENGLISH VERSION
CURV Dimming
WHITES CALIBRATION (CAL)
• Enter the <CAL> to select white color of different
color temperature.
• Select the <ZOOM> range. <POS1> & <POS2> set the
small position for the zoom function. Note that when
using DMX to control the fixture, the user will only be
able to access up to the set ZOOM position. It is not
possible to adjust beyond the set position.

FRESNELED MAX
P.
10
ENGLISH VERSION
5. USING A DMX512 CONTROLLER
CHANNEL ASSIGNMENT
NOTES:
• This product have two DMX512 channel configura-
tion: <UNO> / <DOS> / <STD.P>