Teeter Hang Ups F9000 User manual

F71002
ITEMSFORASSEMBLY ITEM #’s
A-frame base F71002
w/ EZ-Angle Tether Strap F51008
Main shaft w/ ankle clamp F91039
Table frame with mat F51021
Hand grips (2) and F51069
13 mm (1/2”) hex bolts (6) H11202
Two (2) roller hinges F51064
Two (2) wrenches F51088
F91039
F51021
Bolts may be
packaged
separately or
assembled in
hand grips.
H11202
F51069
F51064
F51088
ASSEMBLYINSTRUCTIONS
DONOTDISCARD - KEEP FORFUTURE REFERENCE.
ASSEMBLY
Figure 2
(L)
(R)
NOTE: Bolts may be
packaged separately
or assembled in
hand grips.
U.S. and foreign patents apply. Other foreign patents pending.
Figure 1
Spreader Arms
front rear
1. It is your responsibility to familiarize yourself with the proper use of the equipment and the inherent risks of inversion, such as
falling on your head or neck, pinching, entrapment or equipment failure.
2. This product is not designed for persons over 198 cm (6’6”) or 136 kg (300 lbs). Structural failure could occur or head/neck may
impact floor during inversion. Serious injury or death could result.
3. DO NOT use this equipment without a licensed physician’s approval and a review of the medical contraindications, as noted in
the Owner’s Manual.
4. Failure to assemble and/or use the equipment as directed may void the manufacturer’s warranty on this product and could result
in injury or death.
5. DO NOT use the inversion table until you have thoroughly and carefully read the Owner’s Manual, viewed the Instructional Video,
reviewed all other accompanying documents, and inspected the equipment. The Instructional Video is in English. The steps in
the video directly coincide with the steps detailed in these Assembly Instructions.
6. Choose a level surface for assembling and operating the table.
7. Follow each step in sequence. Do not skip ahead.
8. Make sure that all fasteners are secure.
9. PRIOR TO USE, test and inspect the table.Make sure the table rotates smoothly to inverted position and back.
10. Replace defective components immediately and/ore keep the equipment out of use until repair.
STEPONE
Assemble the A-frame Base (F71002)
• Open the A-frame and make sure that the spreader arms are locked flat. (See
Figure 1)
STEP TWO
Install Hand Grips (F51069) on A-frame Base (F71002)
• Place one of each hand grip (left / right) over the outside edge of the corre-
sponding hinge plate. (See Figure 2)
• Insert three 13 mm (1/2”) hex bolts (H11202) through the hinge plate into each
hand grip. Use the wrenches provided to tighten the bolts, being careful not to
over tighten.
Carefully remove the individual parts from the carton. You should have all of the items listed below. If any items are missing or
damaged, contact your retailer or customer service directly (See Pg. 4).
Before you begin: These instructions will guide you in properly assembling the unit. Please review all the steps before beginning
assembly. Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure user safety and product integrity.
PRE-ASSEMBLY
WARNING
!
F9000TM
F51008

Assembly Instructions #IIL202 Pg. 2
Figure3B
ASSEMBLY
Figure 3
Figure3A
Hinge
into
bracket
Close
cam lock
In Setting C
pivot
pin
Figure 4
Figure 4A
Figure 5
de-rattler
knob
Refer to the Owner’s Manual for an explanation of the hole settings.
We suggest using Setting C to start.
STEP THREE
Install Roller Hinges (F51064) to Table Frame (F51021)
• For ease of assembly, rest the table frame against the crossbar at the
frontoftheA-frame.
• Open the cam locks on each side of the table frame.
• Withthe grooved pivot pinsfacing out, insertthe roller hingesinto the
bracketson each sideof thetableframe. (See Figure3) The rollerhinges
will slide between the cam locks and the brackets. (See Figure 3A)
• Make sure that the roller hinges are in the same hole setting on both
sides.
• Push down on the cam lock to secure the hinge. Figure 3B shows the
rollerhingeengaged correctly (in SettingC).
STEP FOUR
Attach the Table Frame (F51021) to the A-frame (F71002)
• Holdingeachsidenear the roller hinges, pickupthetableframeandstandat
thefrontof theA-frame. LowereachpivotpinintotheA-frame hingeplatesat
thesametime.(SeeFigure4) Figure4Ashowsthecorrectplacementofthe
pivotpin into the hingeplate.
• Make sure that both pivot pins are seated at the base of the slot in the
hingeplate.
• Check to make sure that the self-locking hooks have closed over both
pivot pins and that the table rotates smoothly.
Failure of the self-locking hooks to close over both pivot pins
is indication of improper assembly and if not corrected,
could result in serious injury or death.
STEP FIVE
Insert the Main Shaft (F91039) into the Table Frame (F51021)
• Loosenthe de-rattler knob onthe mainshaft housing.
• With the height adjustment settings on the main shaft facing up, slide the
end of the main shaft into the blue bushing in the main shaft housing. (See
Figure5)
• Pull out the height selector locking pin to allow the main shaft to slide in
further. For the purpose of easy assembly, slide the main shaft in all the
way and release the pin in the storage setting. (Refer to the Owner’s
Manualforproperheightadjustmentbeforeuse).
• Tightenthede-rattlerknob.
Read the Owner’s Manual for information on
selecting the correct user height setting.
Improper settings could result in serious injury or death.
WARNING
!
WARNING
!

ASSEMBLY
Assembly Instructions #IIL202 Pg. 3
CHANGING THE ROLLER HINGE SETTING
• Stand with your legs on either side of the main shaft.
• Reachundereach roller hingewith yourindex fingers. Useyour thumbsto
release the locks over the roller hinges. (See Figure 7)
• Lift both sides of the table out of the A-frame at the same time. You may
rest the table on the crossbar of theA-frame.
• Unlock the cam locks for each roller hinge. Change the roller hinges to
the desired setting (A, B, or C, from most aggressive to least aggressive).
(See Figure 8)
• Relock the cam locks. Replace the roller hinges into the hinge plates of
theA-frame.
Figure 7
Figure 8
A
B
C
Shows pin in
Setting C
STEP SEVEN
Testing the Assembly
PRIOR TO USE:
• Test the table by hand for smooth and steady rotation.
• Ensureall fasteners are secure.
You have completed the assembly of your Teeter Hang Ups®Inversion Table.
• Read your Owner’s Manual thoroughly before using the inversion table. Improper
settings could result in serious injury or death.
• For your reference, the table’s serial number can be found at the base of the table
frame on the back.
POST ASSEMBLY ADJUSTMENTS 

MAINTENANCE 

STORAGE
Hook tether
strap here.
STEP SIX
Attach the Tether Strap (F51008) to Limit the Degree of Rotation
• Attach the clip to the desired strap angle and hook the clip to the loop at
the base of the table bed.
• 20° - Secure the clip to the green strap for inversion to a gentle 20°.
• 40° - Secure the clip to the blue strap for inversion to a moderate 40°.
• 60° - Secure the clip to the black tip of the strap for inversion to a
more advanced 60°. This is the angle when all the benefits of inversion
are realized.
• 90° - Remove the tether strap entirely for full inversion and exercise!
40° blue
20° green
60° black
No Strap:
90°
Figure 6

TABLE MAT: TIGHTENING
• If you feel the nylon mat needs to be tightened, pull the adjustment straps
on the back of the mat.
Assembly Instructions #IIL202 Pg. 4
Figure 9
STORING THE INVERSION TABLE
IMPORTANTNOTE: The F9000TM will not foldfor storage whilein Setting “C”
of the roller hinge. You must have the roller hinge set in either the “A” or “B”
setting to do so.
• Loosenthede-rattlerknob.
• Pull the height selector locking pin and slide the main shaft in all the way
to the ankle clamp assembly. Engage the pin in the storage setting.
• Rotate the table opposite from use until the table has turned 180 degrees
and rests against the cross bar on theA-frame.
• Thelegs of theA-framebase may then befolded together forcompact
storage.(Seefigure 9). WARNING: This operation may pinch fingers if
not done slowly and carefully.
For information about the Teeter Hang Ups®5-year warranty, or if you have any problems
assembling the equipment or questions about its use, please contact Customer Service at the
appropriate location below:
U.S.andforeignpatentsapply. Otherforeignpatentspending.
TeeterHangUps®isaregisteredtrademarkofSTLInternational,Inc.
andInversionInternational,Ltd.
Specificationssubjecttochangewithoutnotice.
©COPYRIGHT2004,InversionInternational,Inc.
InternationalLawProhibitsAnyCopying,11/04
* any modification to this device
will void the UL Classification
Classified as Medical
Equipment, part I in accordance
with UL 2601-1 and CAN/CSA
C22.2; General Requirements
for Safety in accordance with
Underwriters Laboratories, Inc.
TABLE MAT: REMOVING / CLEANING
• You may find it easier to remove the nylon mat while the table is in its
storageposition.
• Pull up on the plastic tension clips to loosen the adjustment straps.
• Release one corner at a time, then slide the mat off the frame.
• The mat should be washed in cold on gentle cycle. Replace the mat on
the table frame while still wet.
• To tighten the nylon mat, pull the adjustment straps on the back of the
mat.
ASSEMBLY
USA & Canada:
STLInternational, Inc.
9902162nd St.Ct. E., Puyallup, WA98375
TollFree(Phone)800-847-0143 (Fax) 800-847-0188
Local(Phone)253-840-5252 (Fax) 253-840-5757
(email) [email protected] (web)www.STLIntl.com
International:
InversionInternational,Ltd.
POBox:AP59245,NewProvidenceIsland,Bahamas
(Phone) [phone] (Fax) [phone]
(email) [email protected] (web)www.InversionInternational.com
European Distributor:
TeeterLtd.
CygnetHouse, Sydenham Road,CroydonSurrey, CR0 2EE,UnitedKingdom
(Phone)[phone](Fax)[phone]
(email) [email protected] (web)www.TeeterLtd.com
AuthorizedRepresentativeaccording to MDD93/42/EECMDSS
MurckhardstraBe1,30163Hannover, Germany