Tek-Trol Tek-Bar 3110B User manual

Quick Start Guide
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] [phone] www.tek-trol.com

Tek-Bar 3110B

1. Before You Begin
Before installation check the model, specications, and installation location for the transmitter. Follow the
Operating Instruction Manual for detailed installation and other information.
Do not remove the transmitter cover in explosive atmospheres when the circuit is live.
Before connecting a HART-based communicator in an explosive atmosphere, make sure the instruments
in the loop are installed in accordance with appropriately safe eld wiring practices.
Trained, qualied specialists must carry out installation of the device. The specialist must have read and
understood these Operating Instructions and must follow the instructions they contain.
Do not clean or touch diaphragm seals with any hard or pointed objects.
When using the measuring device in hazardous areas, installation must comply with the corresponding
national standards and regulations and the Safety Instructions, or Installation or Control Drawings.
2. Unpack
3. Dimensional Drawings
Tek-Bar 3110B Smart Dierential Pressure Transmitter
Drawing /Dimension with Display
Quick Start Guide
Quick Start Guide
6 ¼"
(153.5mm)
3½"
(88.5mm)
4 "
(100mm)
5¼"
(130.75mm)
7 ¾"
(196.75mm)
4¼"
(107.5mm)
3¾"
(91.5mm)
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] [phone] www.tek-trol.com


5. Display
Tek-Bar 3100
Tek-Bar 3110B
The display module is used for eld adjustment to complete the parameters settings and site conguration
before measuring. The local display enables all of the important parameters to be read directly at the measuring
point and to congure the device using the function matrix. It has 5-digit LCD display.
4. Mounting
(91.5mm)
(107.5mm)
(100mm)
(120mm)
(216.5mm)
(153.5mm)
(88.5mm)
Technology Solutions
4¼"
3¾"
6 ¼"
"3½
"4
4¾"
8¾"

7. Grounding
6. Power Supply Wirings
Quick Start Guide
Quick Start Guide
Label Two Wires Three Wires Four Wires
+
-
Power + Power +
Power - Power -
Signal +
Power +
Power -
Signal +
Signal -
A
B
A B
+ -
+ -
A B
+ -
A
3
1
2
+ +
- -
P+ P-
Power
S- S+
Signal
• Shielded twisted pair signal cable is used to avoid ground loops.
• Shielded signal cable is used for signal grounding, insulated oating at the side of pressure transmitter, and
grounding at the control cabinet.
• Internal ground terminals are used for direct grounding.
1 Power supply+ is connected with transmitter terminals+
2 Signal+ is connected with transmitter terminals-
3 Signal- is connected with power supply-
Transmitter
Terminals
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] [phone] www.tek-trol.com


8. Congurations
• Shielded twisted pair signal cable is used to avoid ground loops.
• Shielded signal cable is used for signal grounding, insulated oating at the side of pressure transmitter, and
grounding at the control cabinet.
• Internal ground terminals are used for direct grounding.
The top nameplate (right side only) is located in the upper part of the transmitter. Slide the nameplate until the
Zero/Span button is visible and fully accessible. External buttons operation is used in dangerous areas.
9. Installation of Transmitter
Liquid Flow Measurement
• Place the taps to the side of the line to prevent sediment deposits on the transmitters process isolators
• Mount the transmitter beside or below the taps so gases can vent into the process line
• Mount drain/vent the valve upward to allow gases to vent
Tek-Bar 3110B
Technology Solutions
Flow

Quick Start Guide
Quick Start Guide
Gas Flow Measurement
• Place taps in the top or side of the line
• Mount the transmitter beside or above the taps so liquid will drain into the process line
Steam Flow Measurement
• Place taps to the side of the line
• Mount the transmitter below the taps to ensure that the impulse piping will stay lled with condensate
• In steam service above 250 °F (121 °C), ll impulse lines with water to prevent the steam from contacting the
transmitter directly and to ensure accurate measurement at start-up
Note: For steam or other elevated temperature services, it is important that temperatures at the process
connection do not exceed the transmitters process temperature limits.
Flow
Flow
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] [phone] www.tek-trol.com


Tek-Bar 3110B
Technology Solutions
10. Analog buon programming menu
Keys operation

Quick Start Guide
Quick Start Guide
Detailed operating instructions
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] [phone] www.tek-trol.com


Tek-Bar 3110B
Technology Solutions

Quick Start Guide
Quick Start Guide
11. Modbus Programming Menu
Keys operation
Detailed operating instructions
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] [phone] www.tek-trol.com


Tek-Bar 3110B
Technology Solutions

Quick Start Guide
Quick Start Guide
100.00
12. Menu Tree
Current parameters
Measuring Interface
Set parameters Display modified
parameters
SET
DISP DISP
SET
DISP
mA
mA
mA %
Congure display mode
Enter settings
Confirm and enter the next menu
Modify parameters
Current parameters Set parameters Display modified
parameters
SET
U
SET
U
PSI U PSI MPa
Congure the unit
Confirm and enter the next menu
Confirm and enter the next menu
Current parameters Display modified
parameters
Display modified
parameters
LRV LRV LRV
-10.01
Congure 4mA pressure value
Confirm and enter the next menu
-10.00
5.457
-10.00
Current parameters Display modified
parameters
Display modified
parameters
URV URV URV
Congure 20mA pressure value
Confirm and enter the next menu
100.00 100.01
Display modified
parameters
Display modified
parameters
Display modified
parameters
Display modified
parameters
Display modified
parameters
Set parameters
DAMP S DAMP S DAMP S
Congure damping time
Confirm and enter the next menu
0.0100 0.0100 0.0101
Current parameters
Congure output signal type
Confirm and enter the next menu
mA LINER
SET
SET
SET
mA mA LINER
Current parameters
Congure fault alarming signal
Confirm and enter the next menu
ALARM ALARM NO NO ALARM H
SET SET
Current parameters
Set parameters
FIX\C NO FIX\C NO FIX\C mA
Fix output current
Exit and back to measuring interface
3.8000
Current parameters
Set parameters
Enter settings
Enter settings
Enter settings
Enter settings
Enter settings
Enter settings
Enter settings
Confirm and output calibration current
Confirm and output calibration current
Confirm and output calibration current
Confirm and output calibration current
Modify parameters
Modify parameters
Modify parameters
Modify parameters
Modify parameters
Modify parameters
Modify parameters
Parameters table
Display mode
Lower range value
Units
%
PV
mA
Percentage
kPa
MPa
Process variable
Current
bar
psi
mmHg
mmHO
mHO
inHO
inHg
mHg
TORR
mbar
g/cm
kg/cm
Pa
ATM
mm
m
-19999-99999
Upper range value
-19999-99999
Damping time
0 to 100S
Square root
LinearityLINER
Output signal type
√
None
20.8 mAH
3.8 mAL
Fault alarm signal
NO
(none)
3.8000 mA
4.0000 mA
8.0000 mA
12.000 mA
16.000 mA
20.000 mA
20.800 mA
Output current
NO
796 Tek Drive, Crystal Lake, IL 60014 USA [phone] [phone] www.tek-trol.com


Tek-Bar 3110B
Technology Solutions
Tek-Dpro Flow Solutions
Tek-Trol LLC
Tek-Trol Solutions BV Tek-Trol Middle East FZE
PO Box 121 Windsor, Colorado
80550, USA
Sales: [phone]
796 Tek Drive Crystal Lake, IL
60014, USA
Sales: [phone]
Florijnstraat 18, 4879 AH
Etten-Leur, Netherlands
Sales: [phone]
SAIF Zone, Y1-067, PO BOX No.
21125, Sharjah, UAE
Sales: [phone]
Support: [phone] Email: [e-mail] www.tek-trol.com