manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. TEKA ILLUMINATION
  6. •
  7. Outdoor Light
  8. •
  9. TEKA ILLUMINATION PRP User manual

TEKA ILLUMINATION PRP User manual

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
5/64” Allen Wrench
Waterproof Wire Connectors
Gloves
NEEDED
FOR
INSTALLATION:
By Others
DATE
9-25-17
REFERENCE NUMBER
INS-2533-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.tekaillumination.com • [email protected]
Wear Gloves
Hot Surface
Warning Low Voltage
Shade
Heavy Duty
Stem
1/2” NPT
Adaptor
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
PROJECTOR PATHLIGHT (PRP)
IMPORTANT - WEAR GLOVES TO AVOID GETTING FINGERPRINTS ON THIS PRODUCT. MANY TEKA ILLUMINATION PRODUCTS ARE DESIGNED TO NATURALLY PATINA.
OILS FROM YOUR SKIN WILL ACCELERATE THIS PROCESS WHERE TOUCHED AND ARE NEARLY IMPOSSIBLE TO REMOVE. THIS PROCESS OCCURS OVER TIME AND IS
DETERMINED BY THE INSTALLATION ENVIRONMENT.
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Please refer to the low voltage design guide at www.tekaillumination.com/lvguide before installation for proper wire selection.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS
Locknut
Optical System
DATE
9-25-17
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.tekaillumination.com • [email protected]
REFERENCE NUMBER
INS-2533-00
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
WIRING DIAGRAM
LED - For use with 12VAC
remote transformer or magnetic
transformers only. TEKA Illumination
cannot guarantee performance with third
party manufacturers’ transformers.
1. Loosen two (2) #8-32 set screws on shade
assembly using a 5/64” Allen wrench and remove.
To Replace Components
4. Replace shade assembly. Tighten two (2) #8-32
set screws on shade assembly using a 5/64” Allen
wrench.
PROJECTOR PATHLIGHT (PRP)
2. Loosen two (2) #8-32 set screws with 5/64” Allen
wrench on heatsink body to disengage LED
assembly.
3. Disengage LED assembly and driver. Replace
with new LED and driver assembly. Tighten two
(2) #8-32 set screws on heatsink with 5/64” Allen
wrench to secure.
1. Mount stem onto suitable enclosure and/or
mounting option according to designed lighting
plan. 3. Make watertight connections from remote
magnetic transformer to fixture leads using
waterproof wire connectors (By Others). See
wiring diagram.
2. Secure stem with locknut (Provided).
120V 12V
Fixture
COM
Remote
Transformer
COM

Other TEKA ILLUMINATION Outdoor Light manuals

TEKA ILLUMINATION LARGE BEACON WALL MOUNT User manual

TEKA ILLUMINATION

TEKA ILLUMINATION LARGE BEACON WALL MOUNT User manual

TEKA ILLUMINATION TMC User manual

TEKA ILLUMINATION

TEKA ILLUMINATION TMC User manual

TEKA ILLUMINATION TR5 User manual

TEKA ILLUMINATION

TEKA ILLUMINATION TR5 User manual

TEKA ILLUMINATION MBP User manual

TEKA ILLUMINATION

TEKA ILLUMINATION MBP User manual

TEKA ILLUMINATION 1130 User manual

TEKA ILLUMINATION

TEKA ILLUMINATION 1130 User manual

TEKA ILLUMINATION POWER CANOPY User manual

TEKA ILLUMINATION

TEKA ILLUMINATION POWER CANOPY User manual

TEKA ILLUMINATION TOWER BOLLARD User manual

TEKA ILLUMINATION

TEKA ILLUMINATION TOWER BOLLARD User manual

TEKA ILLUMINATION BEACON WALL MOUNT User manual

TEKA ILLUMINATION

TEKA ILLUMINATION BEACON WALL MOUNT User manual

Popular Outdoor Light manuals by other brands

Gainsborough K764 quick start guide

Gainsborough

Gainsborough K764 quick start guide

Hubbell Killark KFLX Series INSTALLATION, OPERATION & MAINTENANCE DATA SHEET

Hubbell

Hubbell Killark KFLX Series INSTALLATION, OPERATION & MAINTENANCE DATA SHEET

JONATHAN Y JYL6600A quick start guide

JONATHAN Y

JONATHAN Y JYL6600A quick start guide

Kichler Lighting HELEN 37536 instructions

Kichler Lighting

Kichler Lighting HELEN 37536 instructions

SImx ELITE LED LHTC637 installation instructions

SImx

SImx ELITE LED LHTC637 installation instructions

HEPER LW8034.003-US Installation & maintenance instructions

HEPER

HEPER LW8034.003-US Installation & maintenance instructions

Feiss OL13607 installation instructions

Feiss

Feiss OL13607 installation instructions

IKEA BJÖRKSPIREA Assembly instruction

IKEA

IKEA BJÖRKSPIREA Assembly instruction

Panlux BL0408 instructions

Panlux

Panlux BL0408 instructions

Cariboni ORAO Pole side manual

Cariboni

Cariboni ORAO Pole side manual

RH ANVERS TASK quick start guide

RH

RH ANVERS TASK quick start guide

LI-TIAN LIGHTING LT-XT-08 installation instructions

LI-TIAN LIGHTING

LI-TIAN LIGHTING LT-XT-08 installation instructions

Hay BRANCH SLANT instruction manual

Hay

Hay BRANCH SLANT instruction manual

MELINERA 273117 Operation and safety notes

MELINERA

MELINERA 273117 Operation and safety notes

OBI Cossato Series manual

OBI

OBI Cossato Series manual

HEPER LF8017.693-US Installation & maintenance instructions

HEPER

HEPER LF8017.693-US Installation & maintenance instructions

Safavieh Lighting TBL4161 user manual

Safavieh Lighting

Safavieh Lighting TBL4161 user manual

Trilux 8841 LED Mounting instructions

Trilux

Trilux 8841 LED Mounting instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.