Tekmar tekmarNet 2 530 User manual

tekmarNet®2 Thermostat 530
Installation & Operation Manual
D530
12/11
Zoning Replaces:08/10
1 of 28 © 2011 D 530 - 12/11
The tekmarNet®2 Thermostat 530
provides operation for:
One Stage Heat
One Stage Cool
One Fan
•
•
•
Introduction
Features
Zone Synchronization
Zone Post Purge
Intelligent setback (Timer 033)
One touch overrides (with optional
User Switch)
Auto Heating Cycle
Cooling Interlock
tekmarNet®2 communication
compatible
Requires 2 wires
One stage heat, cool, and fan
Pulse Width Modulation
CSA C US Approved for use in
USA and Canada
Outdoor temperature display
Air Group master
Backlight
Freeze Protection
Equipment Exercising
Auto heat-cool switchover
Room Temperature Limiting
Hydronic Cooling
Supports Radiant Floor Cooling
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Note
tN2 Zone Manager, Expansion
Module, Wiring Center or House
Control required for operation
•

2 of 28© 2011 D 530 - 12/11
Congratulations on the purchase of your new tekmar thermostat.
This manual will step through the complete installation, programming and sequence
of operation for this control. At the back, there are tips for control and system
troubleshooting.
Getting Started
Preparation
tekmar or jeweller screwdriver
Phillips head screwdriver
•
•
Wire Stripper•
Tools Required
------------------------------------------------------
------------------------------------------------------
Materials Required
--------------------------------------------------
--------------------------------------------------
2, #6 x 1” Wood Screws
18 AWG LVT Solid Wire
(Low Voltage Connections)
•
•
Optional Adapter Plate 007 (for
installation on 2” x 4” gang box)
•
Installation
Table of Contents
Getting Started ..............................2
Installation .........................................2
Caution..........................................2
Preparation....................................2
Removing The Thermostat Base...3
Mounting The Thermostat Base....3
Thermostat Wiring.........................4
Testing the Thermostat Wiring ......5
Mounting the Thermostat ..............6
Cleaning the Thermostat...............6
Switch Settings ..................................7
User Interface....................................8
Display...........................................8
Symbols Description .....................8
Button Operation ...........................9
Settings .................................. 10-17
Sequence of Operation....................18
Heating Operation .......................18
Cooling Operation .......................19
Floor Cooling...............................20
Fan Operation .............................21
Schedules ...................................22
Scenes (System Override) ..........22
Troubleshooting ...............................23
Error Messages......................23-24
Frequently Asked Questions .......25
Job Record..................................26
Technical Data.............................27
Limited Warranty and Product
Return Procedure ........................28
Caution
Improper installation and operation of this control could result in damage to the
equipment and possibly even personal injury or death. It is your responsibility
to ensure that this control is safely installed according to all applicable codes and
standards. This electronic control is not intended for use as a primary limit control.
Other controls that are intended and certified as safety limits must be placed into
the control circuit.

3 of 28 © 2011 D 530 - 12/11
Choose the placement of the thermostats early in the construction process to
enable proper wiring during rough-in.
Consider the following:
Interior Wall.
Keep dry. Avoid potential leakage onto the control.
Relative Humidity max 80% up to 88°F (31°C) decreasing linearly to 50% RH
at 104°F (40°C). Non-condensing environment.
No exposure to extreme temperatures beyond 36-122°F (2-50°C).
No draft, direct sun, or other cause for inaccurate temperature readings.
Away from equipment, appliances, or other sources of electrical interference.
Easy access for wiring, viewing, and adjusting the display screen.
Approximately 5 feet (1.5 m) off the finished floor.
The maximum length of wire is 1000 feet (300 m).
Strip wire to 3/8” (10 mm) for all terminal connections.
Use standard 18 AWG wire for the tN2 connections.
•
•
•
•
•
•
•
•
•
•
•
Installation Location
-------------------------------------------------
-------------------------------------------------
Removing The Thermostat Base
Push
tab
1Remove thermostat
from base
2
To remove the thermostat base:
Place a small slot screwdriver or similar
tool into the slot located on the top of
the thermostat.
While pushing down against the plastic
tab, pull the thermostat away from the
thermostat’s base.
•
•
Mounting The Thermostat Base
Stud
Switch
Box
Thermostat
Base
007 Adaptor
Plate
31/4”
(83 mm)
If a single gang switch box is used,
an Adaptor Plate 007 is required to
mount the thermostat to the box.
Fasten the base of the
thermostat to the adaptor plate.
Feed the wiring through the
openings in the back of the
adaptor plate and thermostat.
Use the upper and lower screw
holes to fasten the adaptor plate
to the box.
•
•
•
Mounted on switch box

4 of 28© 2011 D 530 - 12/11
If a switch box was not used, mount the
thermostat directly to the wall.
Feed the wiring through the openings in
the back of the thermostat.
Use screws in the screw holes to fasten the
thermostat to the wall. At least one of the
screws should enter a wall stud or similar
rigid material.
•
•
Stud
23/8”
(60 mm)
screwhole
23/8”
(60 mm)
screwhole
Thermostat
Base
Wall
Mounted on wallboard
Thermostat Wiring
The thermostat operates a single heating system zone together with a cooling
system and fan.
Power and communication are provided to the thermostat by connecting the tN2
terminals on the thermostat to the tN2 terminals on a tN2 Wiring Center, House Control,
Zone Manager or Expansion Module. tN2 terminals are not polarity sensitive.
Connect the Rc, Y and G terminals on the thermostat to the R, Y and G terminals
on the cooling equipment.
12 34
1234
tNt 530
530
One Stage Heat /
One Stage Cool / One Fan
Mmm YYYY Lot # 12345
Meets Class B: Canadian ICES FCC Part 15
1023-04
tN2
1
tN2
2
Switch Settings:
For instructions see brochure
Use at least 65°C conductors
Setback
Scene
Not used
ON
Not used
Unlock Lock
Off
Off
5
G
4
Y
3
Rc
Relays: 24V (ac) 2A
tN2 Manager, Module
or Wiring Center
Cooling Equipment
1 Stage
Cooling
1 Stage
Fan
G Y R
D
X
Fan
Cooling
tN2 tN2

5 of 28 © 2011 D 530 - 12/11
tekmarNet
®
communication allows for cooling operation from rooms where only 2
conductor wire is available. This requires a Zone Manager 334 or Zone Expansion
Module 324 directly wired to the cooling equipment. Power and communication are
provided to the 530 thermostat from tN2 terminals on the 334 or 324.
324 or 334
tN2 Rc, Y, G
530
Cooling System
D
X
Testing the Thermostat Wiring
Testing the Power
---------------------------------------------------
---------------------------------------------------
If the thermostat display turns on, this indicates that the thermostat is operating
correctly and there are no electrical issues. In the event that the display is off, or
the display is cycling on and off:
1. Remove the tN2 wires from the thermostat.
2. Use an electrical meter to measure DC voltage between the tN2 terminals.
If the DC voltage is 0 V (dc) for 20 seconds, then there is an open or short circuit
in the tN2 wires.
If the DC voltage is 0 V (dc) for 10 seconds and then is 23 to 24 V (dc) for 5
seconds, this indicates the wiring is correct.
3. Connect the thermostat to the tN2 wires connected to a zone on a House Control,
Wiring Center, or Zone Manager.
4. If the thermostat display is off, or is cycling on and off, move the thermostat to
the next available zone on the House Control, Wiring Center, or Zone Manager.
If the thermostat display remains permanently on, there may be a fault with the
previously tried zone on the House Control, Wiring Center, or Zone Manager.
If the thermostat display continues to be off, or is cycling on and off, there may
be a fault on the thermostat.
If a fault is suspected, contact your tekmar sales representative for assistance.
Testing the Heat Zone Output
----------------------------------------
----------------------------------------
1. Press the Mode button to set the mode to Heat.
2. Press the button and set the heating temperature above the current room
temperature. Make sure the display does not show “WWSD”.
3. When the H1 symbol appears on the display, use an electrical meter to check
for voltage on the House Control, Wiring Center, or Zone Manager relay. The
voltage is 24 V (ac) for zone valves, and 120 V (ac) for zone pumps when operating
correctly.
•
•
•
•

6 of 28© 2011 D 530 - 12/11
Testing the Cooling Contact
------------------------------------------
------------------------------------------
1. Press the Mode button to set the mode to Cool.
2. Press the button and set the cooling temperature below the current room
temperature.
3. When the C1 symbol appears on the display, use an electrical meter to check for
continuity on the Rc and Y terminals. If continuity is present, the relay is operating
correctly. If continuity is not present, the thermostat has malfunctioned.
Testing the Fan Contact
----------------------------------------------
----------------------------------------------
1. Press the Fan button to set the Fan to On.
2. When the Fan symbol appears, use an electrical meter to check for continuity
on the Rc and G terminals. If continuity is present, the relay is operating correctly.
If continuity is not present, the thermostat has malfunctioned.
Mounting the Thermostat
To place the thermostat back on the
mounting base:
Place thermostat bottom tabs on
matching mounting base notches.
Pivot top of the thermostat
towards wall, ensuring wires clear
obstructions.
The top clasp makes a clicking
sound when properly closed.
•
•
•
Pivot
Tab
The thermostats’s exterior can be cleaned using a damp cloth. Moisten the cloth
with water and wring out prior to wiping the control. Do not use solvents or cleaning
solutions.
Cleaning the Thermostat

7 of 28 © 2011 D 530 - 12/11
Switch Settings
Switches are set to “On”
position from the factory, and
do not require changing for
most applications.
12 34
1234
tNt 530
530
One Stage Heat /
One Stage Cool / One Fan
Mmm YYYY Lot # 12345
Meets Class B: Canadian ICES FCC Part 15
1023-04
tN2
1
tN2
2
Switch Settings:
For instructions see brochure
Use at least 65°C conductors
Setback
Scene Lock
Not used
ON
Not used
Unlock
Off
Off
5
G
4
Y
3
Rc
Relays: 24V (ac) 2A
12 34
1234
Mm
Meets Class B: C di ICES
Switch Settings:
Setback
Scene Lock
Not used
ON
Not used
Unlock
Off
Off
Switch Position Action
1
ON
SETBACK
The thermostat follows a programmable setback schedule
as a schedule member if available. Requires the installation
of a Timer 033 to use this feature.
OFF
OFF
The thermostat does not follow a programmable setback
schedule.
2
ON
SCENE
The thermostat responds to changes in the scene (system
wide manual overrides). Requires the installation of a User
Switch 479 to use this feature.
OFF OFF
The thermostat does not respond to scenes.
3
ON
LOCK ACCESS LEVEL
Locked to ‘User’ access level. Set to Lock when installation
completed.
OFF
UNLOCK ACCESS LEVEL
Unlock to allow ‘User’ and “Installer’ access level. Set to
Unlock during installation process.
tekmarNet®reset control must also be set to Unlocked
(Installer access level).
4
ON Not used
OFF Not used

8 of 28© 2011 D 530 - 12/11
SECONDARY DISPLAYMAIN DISPLAY
HEAT
Heat is turned on.
COOL
Cooling is turned on.
FAN
Fan is turned on.
SUN
Operating at the occupied
(day) temperature.
MOON
Operating at the unoccupied
(night) temperature.
AIR GROUP MASTER
Thermostat operates the
cooling for a group of
thermostats.
CLOCK
Operating on a
programmable schedule.
LOCK
Locked to ‘User’ access level.
AWAY
Operating at the Away scene
temperature.
tekmarNet®
Communication is present.
WARNING SYMBOL
Indicates an error is present.
WARM WEATHER SHUT
DOWN
The heating system has been
shut off for the summer.
Display
Symbols Description
Switch between
Heat, Cool, Auto
and Off modes
Switch between
Auto, On and %
Fan operation
Adjust the current temperature
or displayed setting up or down
User Interface

9 of 28 © 2011 D 530 - 12/11
Button Operation
The Mode button selects between Auto, Cool, Heat, and Off.
Heat Mode: The heating system operates to maintain the Set
Room Heat temperature.
Cool Mode: The cooling system operates to maintain the Set Room
Cool temperature.
Auto Mode: The heating system operates to maintain the Set Room Heat temperature.
Likewise the cooling system operates to maintain the Set Room Cool temperature.
The thermostat will prevent the Set Room Heat and the Set Room Cool settings
from getting closer than 3°F (1.5°C).
To switch from heating to cooling, the heat must be off for at least a 30 minute
interlock period and the actual Room temperature must be at least 3°F (1.5°C)
above the Set Room Heat temperature.
To switch from cooling to heating, the cooling must be off for at least a 30 minute
interlock period and the Room temperature must be at least 3°F (1.5°C) below
the Set Room Cool temperature. Cooling has priority over heating.
Off Mode: The heating and cooling are shut off except heating for freeze
protection.
Mode
---------------------------------------------------------------
---------------------------------------------------------------
Fan
-----------------------------------------------------------------
-----------------------------------------------------------------
The fan button manually turns the fan on or off.
Auto: Fan is usually off but can operate with heating or cooling.
On: Fan is on all the time.
10 to 90%: Fan operates a minimum of this percentage each hour.
Press the or the button to select the room temperature. The display indicates
whether the “HEAT” or the “COOL” temperature is being changed.
Use the or
button to adjust
temperature.
If in Auto mode, press the Mode
button to toggle between Heat or
Cool temperature adjustment.
Room or Temperature
------------------------------------------
------------------------------------------

10 of 28© 2011 D 530 - 12/11
Settings (1 of 8)
Display Range Access Description Set to
40 to 95°F
(4.5 to 35.0°C)
Default = 70°F
(21.0°C)
Installer User
SET ROOM HEAT Set the room heating temperature while in the event.
40 to 95°F
(4.5 to 35.0°C)
Default = 65°F
(18.5°C)
Installer User
SET ROOM HEAT Set the room heating temperature while in the event.
40 to 95°F
(4.5 to 35.0°C)
Default = 62°F
(16.5°C)
Installer
SET ROOM HEAT AWAY Set the room heating temperature while in the Away scene.
Continued on next page.
• Press and hold down both the and buttons for 2 seconds to change from one step to the next. • Release both buttons once the step has been reached. • Press the or the button to change the setting, if available. • Press and hold down both the and buttons for 2 seconds to go to the next step, OR • After 10 seconds of no button activity, the display goes back to normal operation. • Note: Set switch setting #3 and tekmarNet®system control to Unlock to change Access level to Installer.
Press
+
Together