Tekon PLUS TWP-4AI4DI1UT User manual

TEKON ELECTRONICS AVEIRO, PORTUGAL
P.: [phone] M.: [phone] E.: [email protected]
PLUS TWP-4AI4DI1UT
INSTALLATION GUIDE
TEKON ELECTRONICS AVEIRO, PORTUGAL
P.: [phone] M.: [phone] E.: [email protected]
IG_PLUS_TWP-4AI4DI1UT_E01A

2
DUOS WIRELESS SYSTEM INSTALLATION GUIDE
01
step WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
Pages 4 to 12
02
step TWP-4AI4DI1UT PLUS WIRELESS TRANSMITTER CONFIGURATION
Pages 13 to 19
PLUS TWP-4AI4DI1UT
INSTALLATION GUIDE
Table of contents
03
step TWP-4AI4DI1UT TRANSMITTER ANALOG INPUTS CONFIGURATION
Pages 20 to 23
04
step TWP-4AI4DI1UT TRANSMITTER DIGITAL INPUTS CONFIGURATION
Pages 24 to 29
05
step TWP-4AI4DI1UT TRANSMITTER UNIV. TEMPERATURE INPUT CONFIGURATION
Pages 30 to 32

3
DUOS WIRELESS SYSTEM INSTALLATION GUIDE
PLUS TWP-4AI4DI1UT
INSTALLATION GUIDE
Table of contents
08
step WRP001 PLUS WIRELESS REPEATER CONFIGURATION
Pages 42 to 47
09
step SITE SURVEY
Pages 48 and 50
07
step WGW420 GATEWAY ANALOG OUTPUTS CONFIGURATION
Pages 39 to 41
5.1 LINK LOST OUTPUT
Page 34
5.2 REMOTE CONTROL OUTPUT
Page 36
5.3 EXTERNAL POWER CONTROL OUTPUT
Page 37
06
step TWP-4AI4DI1UT TRANSMITTER DIGITAL OUTPUTS CONFIGURATION
Pages 33 to 38

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
5
INSTALLATION GUIDE PLUS TWP-4AI4DI1UT
01 Connect the antenna to the Gateway.
02 Wiring
Connect the power supply and then the
RS485-USB cable to the Gateway.
TEKON CONFIGURATOR SOFTWARE is only compatible with the Microsoft® Windows® Operating System.
03 Power ON the device.
Wire Indication:
Blue - GND; Brown - +24 VDC; Orange - Data+ (A); Black - GND; Yellow - Data - (B)

6
PLUS TWP-4AI4DI1UT INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
04 Check device connection state by LED indication.
05 Open Tekon Configurator Software1and select PLUS >> Gateway >> Configuration
2
1
3
1 Tekon Configurator software is free of charge and available at www.tekonelectronics.com
10 Seconds to enter
configuration mode
WIRELESS GATEWAY
Normal mode
Green LEDs
permanently on
Red LEDs
permanently on

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
7
INSTALLATION GUIDE PLUS TWP-4AI4DI1UT
07 Select corresponding Port name2.
2You can check device’s serial port name in “Device Manager” on Microsoft ® Windows® operating system.
06 Select serial port corresponding to WGW420 PLUS Wireless Gateway
Click on the Rescan Ports button.

8
PLUS TWP-4AI4DI1UT INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
08 Perform a power cycle on the Gateway.
09 Click on Connect ( ) button to enter configuration mode.
NOTE:
After power up, you have 10 seconds to enter configuration mode by clicking on Connect button ( )
(while green LEDs are permanently on).
In this mode, you can manage device parameters: Modbus Address, Modbus Baudrate, Modbus Parity, Wireless
Network ID and Wireless Channel.

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
9
INSTALLATION GUIDE PLUS TWP-4AI4DI1UT
NOTE:
When the 10-second time frame to enter configuration mode is exceeded, the LEDs will turn permanently red and
the gateway will enter normal operation mode.
To get back in configuration mode, you need to perform a power cycle - step 8.
Green LEDs performing
scan animation
WIRELESS GATEWAY
Configuration mode
The status string at the bottom of the software window provides feedback on ongoing operations.
10
You can also verify configuration mode activation by checking LEDs on the gateway.

10
PLUS TWP-4AI4DI1UT INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
12 Click on Disconnect ( ) button.
11 Take note of device configuration data available, namely: Modbus Address, Modbus Baudrate, Modbus Parity,
Wireless Network ID and Wireless Channel.
NOTE:
The wireless network connection between devices is ensured by setting the same Wireless Network ID and
Wireless Channel parameters.