Tekon WGW420 User manual

PLUS WGW420
INSTALLATION GUIDE
TEKON ELECTRONICS AVEIRO, PORTUGAL
P.: [phone] M.: [phone] E.: [email protected]
IG_PLUS_WGW420_E01A
PLUS WGW420PLUS WGW420

2
DUOS WIRELESS SYSTEM INSTALLATION GUIDE
01
step WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
Pages 3 to 11
PLUS WGW420 WIRELESS GATEWAY
INSTALLATION GUIDE
Table of contents
05
step WGW420 GATEWAY ANALOG OUTPUTS CONFIGURATION
Pages 12 to 14

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION

4
PLUS WGW420 INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
01 Connect the antenna to the Gateway.
02 Wiring
Connect the power supply and then the
RS485-USB cable to the Gateway.
TEKON CONFIGURATOR SOFTWARE is only compatible with the Microsoft® Windows® Operating System.
03 Power ON the device.
Wire Indication:
Blue - GND; Brown - +24 VDC; Orange - Data+ (A); Black - GND; Yellow - Data - (B)

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
5
INSTALLATION GUIDE PLUS WGW420
04 Check device connection state by LED indication.
05 Open Tekon Configurator Software1and select PLUS >> Gateway >> Configuration
2
1
3
1 Tekon Configurator software is free of charge and available at www.tekonelectronics.com
10 Seconds to enter
configuration mode
WIRELESS GATEWAY
Normal mode
Green LEDs
permanently on
Red LEDs
permanently on

6
PLUS WGW420 INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
07 Select corresponding Port name2.
2You can check device’s serial port name in “Device Manager” on Microsoft ® Windows® operating system.
06 Select serial port corresponding to WGW420 PLUS Wireless Gateway
Click on the Rescan Ports button.

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
7
INSTALLATION GUIDE PLUS WGW420
08 Perform a power cycle on the Gateway.
09 Click on Connect ( ) button to enter configuration mode.
( )
NOTE:
After power up, you have 10 seconds to enter configuration mode by clicking on Connect button ( )
(while green LEDs are permanently on).
In this mode, you can manage device parameters: Modbus Address, Modbus Baudrate, Modbus Parity, Wireless
Network ID and Wireless Channel.
( )

8
PLUS WGW420 INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
NOTE:
When the 10-second time frame to enter configuration mode is exceeded, the LEDs will turn permanently red and
the gateway will enter normal operation mode.
To get back in configuration mode, you need to perform a power cycle - step 8.
Green LEDs performing
scan animation
WIRELESS GATEWAY
Configuration mode
The status string at the bottom of the software window provides feedback on ongoing operations.
10
You can also verify configuration mode activation by checking LEDs on the gateway.

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
9
INSTALLATION GUIDE PLUS WGW420
12 Click on Disconnect ( ) button.
( )
11 Take note of device configuration data available, namely: Modbus Address, Modbus Baudrate, Modbus Parity,
Modbus Stop Bits,Wireless Network ID and Wireless Channel.
NOTE:
The wireless network connection between devices is ensured by setting the same Wireless Network ID and
Wireless Channel parameters.

10
PLUS WGW420 INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
13 Modbus Communication
Select Modbus tab of the Gateway and set the previously saved configurations.
Ensure that Port name, Baudrate, Parity and Modbus Address fields are the same as those obtained in
configuration mode.
14
The messages Connected to Modbus and Reading successfully will appear if Serial Port configuration
parameters are correct and the Modbus connection is established.
Click on Connect ( ) button and check operation status at the bottom of the window.

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
11
INSTALLATION GUIDE PLUS WGW420
WIRELESS GATEWAY
Red LEDs permanently on
LED flashes on each wireless
communication
NOTE:
See WGW420 Datasheet to access LED indication information - page 4.

02
step
WGW420 GATEWAY ANALOG OUTPUTS CONFIGURATION

02
step
GATEWAY ANALOG OUTPUTS
13
INSTALLATION GUIDE PLUS WGW420
01 Follow steps 06 and 07 of the PLUS Wireless Gateway Configuration.
02 In Tekon Configurator Software select PLUS >> Gateway >> Analog Outputs menu
2
1
3
NOTE:
Transmitter analog input 1 data is received and stored at the Gateway Modbus address [9].
03 Considering the transmitter configuration with GTW Modbus Index=1, there is a Gateway Modbus Address
Window corresponding to Modbus address window [0-19].
MB Add
0
19
HOLDING REGISTERS - TRANSMITTERS DATA
Description Address
Serial Number (Transmitter Modbus Index-1) x 20+0
Transmitter Model (Transmitter Modbus Index-1)x20+2
RSSI (Transmitter Modbus Index-1)x20+3
Communication Period (Transmitter Modbus Index-1)x20+4
Elapsed Time (Transmitter Modbus Index-1)x20+5
Power Voltage (Transmitter Modbus Index-1)x20+6
Data 0 (Transmitter Modbus Index-1)x20+7
Data 1 (Transmitter Modbus Index-1)x20+9
Data 2 (Transmitter Modbus Index-1)x20+11
Data 3 (Transmitter Modbus Index-1)x20+13
Data 4 (Transmitter Modbus Index-1)x20+15
FW Version Major Minor (Transmitter Modbus Index-1)x20+17
FW Version Revision (Transmitter Modbus Index-1)x20+18
HW Version Major Minor (Transmitter Modbus Index-1)x20+19
9
Data 1Data 1Data 1
(Transmitter Modbus Index-1)x20+9(Transmitter Modbus Index-1)x20+9(Transmitter Modbus Index-1)x20+9
99

14
PLUS WGW420 INSTALLATION GUIDE
02
step
GATEWAY ANALOG OUTPUTS
04 Link Analog Output Index 1 (Gateway) to Analog Input 1 (Transmitter) and configure MB Add Link according to
the previous step. Set minimum and maximum values and click on Write
4000 (4mA)
20000 (20mA)
WIRELESS GATEWAY
Green led permanently on
during a closed current loop
Red led permanently on
during an open current loop
NOTE:
Output index 1 is linked to modbus address [9], according to mapping table of step 03.
Modbus address double word (float 32) value is converted into 4..20 mA scale according to minimum and
maximum defined values.

TEKON ELECTRONICS
a brand of Bresimar Automação S.A.
Avenida Europa, 460
Quinta do Simão
3800-230 Aveiro
PORTUGAL
Sales
P.: [phone]
M.: [phone]
E.: [email protected]
Technical Support
E.: [email protected]