Telguard Digital TG-1 User manual

24 HOUR ZONE (N.C.)
TELCO DIALER
ANTENNA
T
R
1234567
TELGUARD
Digital TG-1
OPEN = NORMAL
SIGNAL
STRENGTH
LEDS
www.Telguard.com
REFER TO INSTALLATION AND OPERATING
INSTRUCTIONS MANUAL. THIS DEVICE COMPLIES
WITH FCC RULE PART 15.
TELULAR CORPORATION
420 Thornton Road, Suite 109
Lithia Springs, GA 30122
[phone] Fax: [phone]
8 9
+
_
JP
4
J7
SIM
J10
SHORTED = RSSI
HOST C/C
1
2
3
4
5
SYSTEM STATUS LEDS
NORMAL MODE
LED #5 GREEN
ON = RADIO INITIALIZING
FLASH = COMMUNICATING
LED #4 RED
ON = WAITING FOR RESPONSE
If flashing with LED 1 = DENIED
(NACK)
LED #3 YELLOW
OFF = MODE 2 (CELL Primary)
FLASH = C/C OFF HOOK CELL
LED #2 RED
SYSTEM TROUBLE, STC (See Table)
LED #1 GREEN
REGISTRATION (See Table)
SYSTEM TROUBLE,
STC (LED #2)
1 FLASH = AC LOW/MISSING
2 FLASH = LBC LOW BATTERY
3 FLASH = Not Used
4 FLASH = NSC NO SERVICE
5 FLASH = RFC RADIO FAILURE
6 FLASH = DTF DIAL TONE FAIL
REGISTRATION
(LED #1)
ON = UNIT REGISTERED
OFF = UNIT NOT REGISTERED
If flashing with LED 4 = DENIED
(NACK) ,
Call Technical Support.
If all LED's flashing = NO RESPONSE,
Check Signal Strength.
SYSTEM STATUS LEDS
RSSI MODE
RSSI Value LED's Lighted RF dBm
NO SVC LED 5*= flash, 4-2 = off n/a
1 LED 5 = on, 4-2 = off < -111 dBm
1 ½ LED 5 = on, 4 = flash, 3-2 = off > -110 dBm
2 LED 5-4 = on, 3-2 = off > -100 dBm
2 ½ LED 5-4 = on, 3 = flash, 2 = off > -90 dBm
(Minimum Signal Recommended)
3 LED 5-3 = on, 2 = off > -80 dBm
3 ½ LED 5-3 = on , 2 = flash > -70 dBm
4 LED 5-2 = on > -60 dBm
*Note: LED 1 ON INDICATES MORE THAN ONE TOWER
AC
LED 6
CAUTION: INCORRECT CONNECTIONS
MAY RESULT IN DAMAGE TO UNIT.
LED MODE SELECT
EARTH
GROUND
STC2
(N.C.)
BATTERY
(12V)
BLANK PIN
AC
(12V 800MA)
TELGUARD DIGITAL TG-1
QUICK INSTALLATION GUIDE
INSTALLATION SUMMARY
There are four steps in installing Telguard properly. IF YOU DO NOT
PROCEED IN THE ORDER AND MANNER PRESCRIBED, YOU MAY
NOT COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.
Complete the Activation Form online at www.Telguard.com or fax the form
to Telular Cellular Service prior to leaving for the job site.
STEP 1: LOCATE UNIT AND MEASURE SIGNAL STRENGTH (RSSI)
First, you will be confirming that Telguard has adequate cellular signal
strength. Put J10 across both pins, LEDS will now indicate signal strength,
minimum recommended is 2 ½ (2 on solid and the third flashing).
STEP 2: REGISTER TELGUARD & TRANSMIT C/C ALARMS OVER
THE CELLULAR RADIO NETWORK
Next, you will be connecting the C/C's digital dialer output to Telguard and
verifying that alarm signals can be reliably sent through Telguard over
cellular to the central station digital receiver. The incoming Telco line is not
connected to Telguard during this step. A minimum of two alarm signals
must be transmitted.
(NOTE: THE FIRST ALARM WILL REGISTER THE UNIT WITH THE
TELULAR COMMUNICATION CENTER, IT WILL NOT GO TO THE
CENTRAL STATION, ALL SIGNALS AFTER THE FIRST ARE SENT TO
THE CENTRAL STATION)
STEP 3: CONNECT SUPERVISORY TRIP OUTPUTS
Next, you will wire Telguard's supervisory trip output to the C/C and then
test.
STEP 4: COMPLETE THE INSTALLATION
Your last step will be to check the jumper setting of J10 (LED mode, open =
normal), attach earth ground, and permanently mount the unit.
56034101

Setup & Programming the Operating Parameters in the Telguard
When the Telguard is received from the factory and is powered up for the first time, it is immediately ready for
registration, provided the default settings are what you want. The STC LED will flash to indicate any failure conditions.
The Mode LED will be on and the STC relay will be tripped. If changes are required to the default settings, the Telguard
can be programmed using a line-mans butt-set connected to T & R Test Points or a POTS phone connected to J7
(where the C/C is normally connected).
TO PROGRAM THE TELGUARD
A. Put the line-mans butt-set in talk mode or pick up the POTS phone.
B. Connect power to the Telguard, when ready for programming you will hear 2 beeps.
C. Press #, *, this will put the Telguard into a Master Access programming mode, 2 beeps.
D. Enter changes required.
The syntax for programming a specific memory location is as follows:
MEMORY LOCATION (3-digits), will respond with 2 beeps, then VALUE, will respond with 2 beeps.
E. Then press *, you will hear 2 beeps then hang up. This saves the change and exits the programming mode.
MEM LOC. FIELD DEFAULT
VALUE
SETTING
833 C/C Reporting Format 08 08 = Contact ID
851 STC Trip Output
Reporting
Normally Closed
27 Enter the SUM TOTAL of the events that you wish to trip the
STC relay by ADDING the corresponding values:
00 = STC Trip Input Not Used
01 = AC Failure 04 = not used 16 = RFC
02 = Low Battery 08 = NSC 31 = All
852 STC Trip Delay for NSC 1 1=30 Seconds 2=60 Seconds
861 CFC Number of Events 0 0 = disabled 2 = 4 attempts
1 = 2 attempts 3 = 8 attempts
862 CFC between Events 1 1 = 30 seconds 3 = 70 seconds 5 = 90 seconds
2 = 60 seconds 4 = 80 seconds 6 = 99 seconds
864 RFC Number of Attempts 2 0=Disabled 3 = 3 Attempts 6 = 6 Attempts
1=1 Attempts 4 = 4 Attempts 7 = 7 Attempts
2=2 Attempts 5 = 5 Attempts 8 = 8 Attempts
867 Standby Battery Size 3 0 = No Battery 2= 1.2 ah 4 = 7 ah
1 = 0.8 ah 3 = 4 ah
872 AC Failure Delay 02 0-24 hours, default = 2 hours
899 Factory Default Unit