Texecom Premier Elite Impaq Contact-W User manual

INS 468-6
ASSEMBLY
For rear tamper - fix both the detector AND the rear tamper insert to
the mounting surface. Activation of rear tamper will damage product.
Rear Tamper Insert
Relearn
MAG1 COM MAG2
Reed
Disable
Reed Switch
Reed Disable
Magnet
Non-Ferrous Mounting Material
•Maximum Break = 30mm
•Minimum Make = 15mm
Ferrous Mounting Material
•Maximum Break = 15mm
•Minimum Make = 5mm
Note: Values depend on
mounting material. See Fig.1
Disabled
Enabled
Battery
Only replace with 3V Lithium CR123A.
Battery Safety
• Do not throw into a fire
• Do not heat
• Do not charge
• Do not short circuit
• Do not disassemble
• Replace only with same or equivalent type
• Always observe local regulations when
disposing of a battery
• Detector will transmit low battery warning
when battery needs replacing
Relearn
Place jumper on Relearn pin
header and insert battery to
learn device.
For wiring external wired
contacts/switches
LED
INTRODUCTION
• Forwirelessconnectivity,detailedprogramming andsystemset-up
instructionspleaserefertothecompatibleRICOCHET™technology
enabledPremier Elitewirelessexpanderinstructions.
• FeaturingRICOCHET™wirelesstechnologytheImpaq Contact-Wis
designedforprofessionalsecurityinstallations.
• WhenusingtheImpaq Contact-WonanEntry/Exitroute,ora24HR
door,orwherechimeisrequired,thedeviceattributesshouldbeleft
atdefault“AlwaysAwake”.
• Pleasesee thePremier Elite 8XP-W/32XP-WInstallation Manualfor
detailsofhowtochangethedeviceattributes.
Instruction Manual
Premier Elite Impaq Contact-W

LED STATUS INDICATION
Only available in walktest mode
(See Premier wireless expander instructions)
STANDARDS
Impaq and the wireless logo are trade marks of Texecom Ltd. © 2012
The Impaq Contact-W is protected by European Registered Design. No: 269188-0001
D20120815 INS468-6
WARRANTY
2 year replacement warranty (excludes battery).
The Impaq Contact-W is designed to detect the opening of
a door/window and activate an alarm control panel. As the Impaq
Contact-W is not a complete alarm system, but only a part thereof,
Texecom cannot accept responsibility or liability for any damages
whatsoever based on a claim that the Impaq Contact-W failed to function
correctly.
Due to our policy of continuous improvement Texecom reserves
the right to change specification without prior notice. All specifications
are measured at 20ºC (68ºF).
CertificateNumber:FM35285
Made In
England
ADDITIONAL INPUTS 1 & 2
Flashing Green: Withallcontactssecure,willflashevery
3seconds.
Red: Indicateseitherthereedswitchorexternal
contactsareactive.
The Impaq Contact-W has 2 additional inputs. These may be used for any
N/C device and utilise wireless signal transmission to the receiver. Typical
examples for use are:-
• Any locally powered device with a N/C output e.g. Smoke detectors,
Glass Break detectors, Movement Sensors, Flood detectors etc.
• Any non-powered N/C device, e.g. Additional magnetic contacts, fixed
PA buttons etc.
• The in-built reed switch can be disabled.
• Configuration and programming options are detailed in the Premier
wireless expander installation manual.
• Certain features and functions are control panel software dependent.
-35°C (-31°F) to
+60°C (+140°F)
88g (3.1oz) approx.
-10°C (14°F) to
+55°C (+131°F)
25mm (1”)
26mm (1”)
130mm
(5.1”)
33mm
13mm
Alarm
Systems:
EN50131-2-2, EN50131-5-3, EN50131-1,
PD6662, Grade 2 Class II*
EMC: EN50130-4:1995: A1: A2
ETSI EN301 489-03 V1.4.1
R&TTE: ETSI EN300-220 (V2.1.1)
Environmental: EN50130-5
Frequency Band: 868.0 - 868.6 MHz / 433.05 - 434.79 MHz
866.0 - 866.6 MHz •See product label
Product Type:
GBC1000-2 Frequency 868MHz
GBC2000** Frequency 433MHz
GBC3000 Frequency 866MHz
Receiver: Category 1, Class 2
Receiver LBT (Listen Before Talk) Yes
Transmitter Duty
Cycle 868Mhz<1%, 433Mhz<10%
Low Voltage Signal 2.85V
Operating Voltage 3V
Maximum current 32mA
Quiescent current 60uA
MAGNET POSITIONING
Fig.1
Y
X
Z
Y
X
Z
Magnetscanbeinstalledeitherside
oftheunit.
Material Approach Removal
Non-
Ferrous
+/-4mm
X=18mm
Y=10mm
Z=22mm
X=20mm
Y=12mm
Z=24mm
Ferrous
+/-3mm
X=8mm
Y=8mm
Z=16mm
X=9mm
Y=9mm
Z=18mm
*Certied by Det Norske Veritas: NORWAY ** Not INCERT approved.