Yale Sync IA-310 User manual

Sync.
Smart Home Alarm
Installation Manual
IA-310
IA-320
IA-330
IA-340

1. Go to Yale web site
www.yale.co.uk/product-registration
2.Complete product information form
3.Activate your guarantee
Thank you for choosing the Yale Sync Smart Home Alarm.
This simple to install system has been designed with the user in mind, just follow
these simple steps:
Register your product guarantee. Please visit the registration web page and insert
the product details. Register your product to get products news and updates.
1
Installation Service
Want us to install this product ?
Why not call Yale Smart Security Partners and
let a professional installer take care of the rest.
Choose your package online at
www.yalestore.co.uk/installation
Choose your
package.
Agree a Date & Time
A B
Enjoy your
professionally installed
Yale product!
23
Date

(03)
1
2
3
4
5
6
7
(p. 04-06)
Unboxing
Location planning
App. download
Smart Hub Installation
Device activation Battery install / replacement
Installation
System setup
App. setup / operations
(p. 07)
(p. 08)
(p. 09-10)
(p. 22-24)(p. 11)
(p. 11)
(p. 18-22
+ 25)
(p. 12-21)
8
Install your system in a few easy steps. Please read through all of the steps shown below and then
follow the detailed instructions in the following pages. See your product box for kit content information

(04)
Smart Hub
IA-HUB
Max. Total 40 pcs.
Motion Detector
AC-PIR
Motion Detector
Pet Friendly
AC-PETPIR
AC-PIR AC-PETPIR
~12m
~12m
110°
~ 1.8
2.1m
~ 1.8
2.1m
1
Max < 27 kg
Door/Window
Contact
AC-DC
Keypad
AC-KP
110°
+ PIN CODE
Panic buttons press/hold
Panic Buttons can activate your
alarm immediately - even when
the system is disarmed.
How to
Disarm
>3sec.<
How to
Full-Arm
How to
Part-Arm
All the devices in this kit are pre-paired for easy installation. If you are adding more devices
(purchased separately to this kit) you will need to pair these into the system separately
(see page 18)

(05)
>3sec.<
Panic Button
AC-PB
1
Keyfob
AC-KF
Smoke Detector
+ Motion / Heat
Detection
AC-PSD
All the devices in this kit are pre-paired for easy installation. If you are adding more devices
(purchased separately to this kit) you will need to pair these into the system separately
(see page 18)
Hold
PIR / Heat detection function
Smoke detection
10 m
5.5 m
2.4 - 3.0 m
C°- F°
Temperature
Detection
The Temperature
Sensor will transmit
temperature signals
regularly according to
setting. The factory
default interval is
10min
• The Smoke Detector
will also send
temperature signal
when temperature
changes by +/- 2°C.
• You can also press
the Test Button once to
transmit a temperature
signal manually.
• The temperature
detection range is
about -10°C ~ 50°C.
( 14°F ~ 122°F)

(06)
Conexis L1
Smart Lock
+
Sync Lock
Module AC-LM
ON / OFF
1
Most of the devices are provided with either internal or external
security tamper mechanism, please make sure the tamper spring
is fully compressed when you install the devices.
All the devices in this kit are pre-paired for easy installation. If you are adding more devices
(purchased separately to this kit) you will need to pair these into the system separately
(see page 18)
Smart Plug
AC-PS

(07)
2
Plan Your home
Location tips:
1. Keypad should be accessible from a protected entry/exit point. Ensure that the Keypad is not visible from
the outside of the premises.
2. Mount Door/Window Contacts as high as possible on the door / window frame.
3. PIR Motion Detectors should be located in the corner of the room to maximise coverage.
Do not point directly at a source of heat (eg.fires or boilers), facing a window or a door protected by a
Door/Window Contact. Avoid installing directly above radiators.
4. If you have Pets that may climb on furniture, avoid using PET PIR Motion detectors as this can cause false
alarms. Instead replace with additional Door/ Window Contacts.
5. Mount the external siren as high as possible on an external wall.
Example
Plan your system: Before beginning the installation process, take some time to plan your
system, decide where you want to locate the devices.

(08)
Yale Smart Living Home
3
IOS 9.0 +
Android 4.2 +
Serial No.
Please register the hub within one hour of power up, otherwise
the app "authentication error" will appear. Re-boot the
hub(including switch off/on the back up battery) and start the
process again if necessary.
Download the app, create an account and follow the on screen step by step set up wizard.

1
2
4
(09)
Smart Hub connection
3
4
Router
NOT INCLUDED
Battery
<On Off>
<On Off>
a
b

(10)
Re-boot
<On Off> <On Off>
HOME SERVER
Network
Shows server connection status
Fault Status
Shows fault status and AC
failure warning
Alarm Mode
Shows arming status
Fully Armed
Part Armed
Disarmed
Check app history log
to see fault details.
4
Smart Hub connection
System normal.

Setting up
Remove battery strips
Test your planned location of components
200
Test location for radio signal strength
Press button to test connection
(11)
65
6
8 9
Device Activation
5

(12)
Installation
7
1
a
a
d
b
b
c
2
3
4
5 6
Ø 5mm

(13)
Installation
7
1
3
5
6 7
2
4
a
b
max
10mm
or
Clean the mounting surface before application
with a suitable degreasing agent

1
1
2
2
3
(14)
Pair / Test button
Ø 5mm
Minimum 60cm
Installation
7
Pair / Test button

(15)
1
a
b
c
~1.8m
2.1m
d
2
a
a
b
3
4
5 6
Ø 5mm
Installation
7

1 2
Pair / Test button
ON
(16)
Installation
7

(17)
1
3
4 5
2
6
a
a
a
b
b
b
c
d
Ø 5mm
7
Installation

Activate learning mode
(18)
All devices in the kit are pre-linked to the Smart Hub. If you want to add more
devices, you can do this by using the “Add device” section in the
Smart Living Home app.
200
Press button to test connection
8 9
1
2
3
Go to the app menu and select
Add Device, then activate learning
mode.
Press the learn button on the device you want to add, the
Smart Hub will beep when the device is added. You will then see
the new device on your app screen.
Exit Learning mode after you have added all the additional devices.
8
App setup / operation: Adding new devices

(19)
Burglar
Home Omit
Entry
Home Access
Part armed mode is usually used to protect the perimeter or a specific zone
of the house (eg. ground floor) while you are free to be inside or in another part of
the house (eg. upstairs)
Go to the App menu
Settings > Alarm settings > Devices
In your device list, go into the settings
for each device and select the required
device mode.
4 different settings are available for PIR Motion Detectors and Door/Window
Contacts. Devices are pre-set to Entry. When the system is armed first users will
have 30 seconds to exit the building. If the system is already armed, triggering any
sensors will cause an entry countdown to begin.
You can change the device behaviour
settings to select the required action
when the system is fully armed or
part armed.
Key
Sensor
Ignored
Instant
Siren
Triggers
Countdown
8
Setting up part armed mode and devices behaviour

(20)
If you want to know more about
your Home App features, check our app
manual sections within the app.
(select the ? at top right of the screen
you need help with)
Changing your Key Pad PIN
You can modify the existing PIN code
using the app.You can set up to 10 sets of 4 digit
PIN numbers in the app.
Go to app menu
Settings > Alarm Settings > Key Pad PIN code settings
Adding new users
To add more users to control your alarm system you
can add a new account in the app.
Go to app menu
Settings > User Settings > Account Management
Managing Alert Notification
You can manage the different type of notifications, choose to have all events or
burglar only reported via email. You can also add phone numbers to receive an
SMS notification when burglar event is reported.
Go to app menu
Settings > User Settings > Notification settings
Settings
8
App setup / operation