Clever CL-IV Manual instruction

CL-IV

is GSM priority , telephone line backup, if enabled this
function, when trigger alarm, it will send alarm information to CMS via GSM in
priority. And send SMS to all voice numbers, including alarm information. If you
want to send arm/disarm text message to user, must set arm/disarm information to
CMS, the setting is: press* last for 3s System password# 4# 9# 2#. If SIM
card charges owed or signal interference, it will send alarm information to CMS and
call voice numbers via telephone line automatically.
Menu
GSM/Tel.line
GSM signal
Note:
9876 is system
password, 1234 is
user password,as
perthe revised
system password
when you operate.
Enabled
Disabled
GSM priority
Tel.line priority
LCD display
is telephone line priority, GSM backup, if alarm occurs,
it will send alarm information to CMS and call voice numbers via telephone line in
priority, if telephone line faulty or was cut, auto turn to GSM.
LCD displayis enabled GSM function
LCD displayis disabled GSM function, only use telephone line
connect CMS and call voice numbers.
GSM ON/OFF
Enter
LCD display
[System password]+[ 0 ]
System password
[System password]+[ 0 ]
[System password]+[ 0 ]
*
1

6.3 GSM control via SMS
2
Set “03000000#”system default no remind. The setting is “03+year+month+date
+# ”, each is 2 bit. When set SIM card successfully, It gives remind during 08 00---21
00 each day on the 10days before or after the preset date .. This function is to remind
the user check SIM charge, in order to make sure GSM can work normally . For example:
set 2010-12-12 as expiration date, setting as below:
EnterLCD disply
Note: 30 is signal strength, the Max. 31, only if
the signal strength above 16, then it can send
alarm information to CMS steadily via GSM.
1.6 GSM alarm receiving
When alarm occurs, GSM will call the preset voice number, it will voice
prompt “system is alarm, please process the alarm, press 1 to cancel the alarm,
press 2 to check alarm zone, press 3 to activate the hoot, press 4 to disabled the
hoot, press 5 to disarm, press 6 to arm, press 7 to standby, press 0 to hang up ”.if
receiving alarm, please press 2 to check in advance, voice prompt“XX zone alarm”,
rst make sure it is false alarm then you can cancel the alarm. Don't error
operation.
Voice prompt “operation successfully”,or else need to re-operate, if you want
to hang up, please press 0, then hang up.
6.2 GSM remote operation
User can remote control the system by phone call, for example arm/disarm
system, and status checking. Y ou can call SIM card number , then panel will o
hook the phone then enter the password, the default password is 1234, as per the
revised user password when you operate, voice prompt“ press 1 to disarm, press 2
to arm, press 3 to standby , press 0 to hang up ”. When operate successfully, voice
prompt “operation successfully”.
:
Arm command:Password:1234
System arm
Disarm command:Password:1234
System disarm
[System password]+[ 0 ]
[System password]+[ 0 ]
Press“ ,” to exit the settings.

7.1 Power on, enable GSM function, if LCD display
If 1,2,4 pulsate on 3 location, SIM card is searching network, it takes about 1 minute, it is
normal phenomenon. If this phenomenon occurs in using, you need to check the power
supply, GSM panel needs 1A power supply, if less than 1A, it will cause GSM restart or
can't send SMS to CMS.
7.2 Don't install the panel close to metal, air-condition, large heat machine.
7.3
7.4
In order to make sure GSM work normally , suggest test the panel at least 1 time per
week. If GSM can't work normally , please check if SIM card charge owed etc.
This user manual just for your reference. Any further questions, please contact the
sales person.
Note: there is no space in the commandpassword1234”, then newline
entersystem arm”, there is no punctuation in the command; the
password as per the user's revised password.; when operate
successfully, SMS auto reply operation successfully”, or else, will
auto reply operation failed”.
“
“
“
“
Status checking command:
Password:1234
System status
Cancel alarm command:Password:1234
Alarm cancel
Home arm command:Password:1234
System home
4