Pyronix Enforcer 32WE User manual

Wireless Setup Guide
RINS1550-4
EN50131-1:2006+A1:2009
EN50131-3:2009
EN50131-6:2008
EN50131-5-3:2005+A1:2008
PD6662:2010
Security Grade 2
Environmental Class II
Software Version >9.13
PIEZO WARNING
The Enforcer 32-WE system contains
a 100dBA siren, please be aware of
this after an activation

Enforcer 32-WE Wireless Setup Manual
Page: 2
CONTENTS PAGE
1. The Enforcer 32-WE .................................................................................................................3
1.1 The Enforcer 32-WE .............................................................................................................3
1.2 The Wireless KF4-WE ...........................................................................................................3
2. Wireless Devices ......................................................................................................................4
3. Powering Up / Entering & Exiting The Engineers Menu ...................................................................5
3.1 Initial Power Up...................................................................................................................5
3.2 The Engineer Menu ..............................................................................................................5
4. Learning Devices......................................................................................................................6
4.1 Learning Inputs ...................................................................................................................6
4.2 Learning Bells .....................................................................................................................7
4.3 Learning Keyfobs .................................................................................................................8
5. Deleting Inputs and Bells...........................................................................................................9
6. Diagnostics ...........................................................................................................................10
6.1 Signal Strength .................................................................................................................10
6.2 Battery Status................................................................................................................... 11
7. Wireless Functions..................................................................................................................12
7.1 Site Options......................................................................................................................12
7.2 Change Timers ..................................................................................................................12
8. Fault Displays ........................................................................................................................13
8.1 Wireless Mismatch .............................................................................................................13
8.2 Wireless Tamper................................................................................................................ 13
8.3 Battery Low ......................................................................................................................13
8.4 Wireless Supervision ..........................................................................................................13
8.5 Jamming ..........................................................................................................................13
8.6 Wireless Poll Fault..............................................................................................................13
9. Wireless Peripherals ...............................................................................................................14
9.1 MC1MINI-WE ....................................................................................................................14
9.2 MC2-WE ...........................................................................................................................16
9.3 MC1SHOCK-WE .................................................................................................................18
9.4 KX12DT-WE ......................................................................................................................20
9.5 KF4-WE............................................................................................................................22
9.6 Deltabell-WE .....................................................................................................................23
10. Notes .................................................................................................................................25
Default Codes:
User Code: 1234
Master Manager Code: 2222
Other Codes:
Keypad Security Code: ‘2000’
Delete All Wireless Data: ‘2000’

Enforcer 32-WE Wireless Setup Manual
Page: 3
1. The Enforcer 32-WE
This manual is intended for 'quick starting' the Enforcer 32-WE in terms of learning inputs, bells and
keyfobs. For all other information please see RINS1549.
1.1 The Enforcer 32-WE
a= Exits the Master Manager menu (page: 16), and selects Area A when setting.
b= Moves backwards in the Master Manager menu (page: 16), and selects Area B when
setting.
c= Enables chime, displays additional information in the event log, and selects Area C
when setting.
D= Moves forward in the log, scrolls between options and enters the Master Manager
menu (page: 16), and selects Area D when setting.
fp = Not used.
[] = Directional buttons and enables/disables functions.
I= Selects commands
A= Cancels items, resets the panel and moves to next item in a menu item.
1.2 The Wireless KF4-WE
The KF4-WE may be used to set and unset the Enforcer 32-WE, as well as other operations.
Refer to page 8 for learning the KF4-WE to the Enforcer 32-WE.
The keyfob has 4 buttons, and 8 programmable actions available.
These can be programmed as:
[1] Show Status
[2] Set Area
[3] Unset Area
[4] Latch Output
[5] Timed Output

Enforcer 32-WE Wireless Setup Manual
Page: 4
2. Wireless Devices
There are a range of wireless devices that can be learnt on to the Enforcer 32-WE system. These are
described below.
Product Name Description Maximum Devices
DETECTORS (INPUTS)
KX12DT-WE 12m Dual Technology Detector
32
KX10DTP-WE 10m Dual Technology Pet Immune Detector
KX12DQ-WE 12m Dual Detector
KX10DP-WE 10m Pet Immune Detector
KX15DC-WE 15m Curtain Detector
KX25LR-WE 25m Long Range Detector
CONTACTS (INPUTS)
MC1/SHOCK-WE Combined Magnetic Contact and Shock Sensor
MC2-WE Magnetic Contact and Universal Transmitter
MC1MINI-WE Magnetic Contact
SENSORS (INPUTS)
SMOKE-WE Smoke Sensor
CO-WE Carbon Monoxide Detector
WL-WE Water Leak Sensor
Product Name Description Maximum Devices
EXTERNAL SOUNDERS (BELLS)
DELTABELL-WE External Sounder 2
Product Name Description Maximum Devices
ARMING DEVICES
KF4-WE 4 Button keyfob 32
All Wireless detectors, contacts, sensors,
and external sounders have a 'LEARN'
button. Once the Enforcer 32-WE is ready to
learn (page: 6), the LEARN button must be
pressed.
There are also 3 LEDs*on each wireless
peripheral that helps to show:
1) Signal Strength
2) Alarm State
NOTE 1: When learning the KF4-WE, a
button needs to be pressed (page: 8)
NOTE 2: The CO-WE and SMOKE-WE only
has one (tri-colour) LED present.
The example above shows a KX12DQ-WE detector.

Enforcer 32-WE Wireless Setup Manual
Page: 5
3. Powering Up / Entering & Exiting The Engineers Menu
3.1 Initial Power Up
1. The initial power up may take a few minutes before
'ENFORCER 32-WE' and the time is displayed on the
display.
2. Once 'ENFORCER 32-WE' and the time are displayed,
programming can begin.
NOTE: It is important that no keys are pressed during the
initial power up period.
3.2 The Engineer Menu
Entering the Engineer Menu Exiting The Engineer Menu
OR
*NOTE: You can only exit the Engineer menu by pressing if a main menu item is displayed (a
main menu item is recognised if the text is all capitals).
Enforcer 32-WE
Time 13:43 c
Please Wait...
Enforcer 32-WE
Time 13:43 c
Enter Your Code
[**** ]
Active Faults
Battery Fault100
SET/UNSET
SYSTEM?
SOFTWARE
REVISION?
Enter the Engineer Code
Any faults are shown. Press 
Press 
Engineers Menu
SOFTWARE
REVISION?
EXIT ENGINEER
MENU?
Press 
Use andto scroll to:
Enforcer 32-WE
Time 13:43 c
Day Mode
SOFTWARE
REVISION?
Use *
Enforcer 32-WE
Time 13:43 c
Day Mode

Enforcer 32-WE Wireless Setup Manual
Page: 6
4. Learning Devices
4.1 Learning Inputs
This section shows how to learn any inputs on to the Enforcer 32-WE. Refer to page: 4 for a list of all
wireless input peripherals available.
It is recommended that all wireless inputs are learned
at the Enforcer 32-WE before final installation. This
makes the learning procedure much quicker.
A maximum of 32 x wireless inputs may be learned.
Once 'Learning' has been completed, the position of
the input in a property must be tested for signal
strength before it is actually ‘fixed’ into place. See
page 10 when analysing the signal strength.
Before learning each input, check that the battery is
present and inserted correctly. To enable the battery
please remove the plastic strip. The LEDs will start
flashing.
Follow the instructions on the right to start learning
the inputs.
An input that is learnt correctly will flash the GREEN
LED briefly and ‘Input Learnt’ will be displayed on the
Enforcer 32-WE display. Both of these instances need
to occur to indicate a successful learn.
Once learning has completed, each input needs to be
given an input type (Final Exit, Intruder,etc.) see the
main programming manual RINS1549 for more
information. The function is called 'CHANGE INPUTS'.
If the Engineer's menu is exited before an input type is
assigned to a learnt input, an error mismatch fault will
be displayed.
Input and Sensors
Detectors
Learning Procedure.
MC1SHOCK-WE MC2-WE MC1MINI-WE SMOKE-WE CO-WE WL-WE
KX12DT-WE KX10DTP-WE KX12DQ-WE KX10DP-WE KX15DC-WE KX25LR-WE

Enforcer 32-WE Wireless Setup Manual
Page: 7
4.2 Learning Bells
This sections shows how to learn any external sounders (bells) on to the Enforcer 32-WE.
It is recommended that all wireless bells are
learned at the Enforcer 32-WE before final
installation. This makes the learning procedure
much quicker.
A maximum of 2 wireless bells (DELTABELL-WE)
may be learned.
Even though the ‘learn’ may be successful, the
position of the bell on a property must be tested
for signal strength before it is actually ‘fixed’ into
place. Refer to page 10 when analysing the signal
strength.
Before learning each bell check that the battery is
present and is inserted correctly.
Follow the instructions to the right to start learning
the bells.
A bell that is learnt correctly will flash the GREEN
LED briefly and display ‘Bell Learnt’ on the keypad.
Both of these instances need to occur to indicate a
successful learn.
Learning Procedure.
DELTABELL-WE
Learning...
In
Press 
Press 
Press 
Select the Bell. Press . If
‘LEARNT’ is shown on a bell,
this will need to deleted before
learning can begin.
Use

and

to scroll to:
When ‘Learning’ is displayed,
press and hold the ‘LEARN’
button on the device until the
LEDs cycle, then release.
If a bell has already been learnt
to the Enforcer system, ‘Bell
Learnt Already!’ will be
displayed. Press .
WIRELESS DEVICE
CONTROL?
Control Inputs?
Press 
Control Bells?
Learn Devices?
Select Bell
Available [1]
Select Bell
Learnt [2]
Bell Learnt
Bell Learnt
Already!

Enforcer 32-WE Wireless Setup Manual
Page: 8
4.3 Learning Keyfobs
This sections shows how to learn any keyfobs (KF4-WE) on to Enforcer 32-WE.
Learning keyfobs can only be done from the
master manager menu. Follow the instructions to
the right to enter the Master Manager Menu (for
more information please see RINS1548).
A maximum of 32 keyfobs can be assigned to the
Enforcer 32-WE. Each keyfob has 4 buttons that
can have specific operations:
[0] No action: Disables the button.
[1] Show Status: If the keyfob is learnt, the LED
will flicker when the nominated button is pressed.
GREEN = Unset. RED = Set.
[2] Set Area: Sets the chosen area.
[3] Unset Any Area: Unsets any area on the
system.
[4] Latch Output: Latches an output
(programmable) when the nominated button is
pressed.
[5] Timed Output: Activates an output for a
period of time (programmable in seconds).
When learning a keyfob, any button must be held
until the LED flashes GREEN and RED, and then
when released, a GREEN LED will be shown,
asterisks will appear in the brackets on the keypad
and an acknowledgement beep will be heard, all
indicating a successful learn.
Keyfob buttons can also be programmed in the
engineer menu, in the same way as shown here
(please see the programming manual for more
information).
Deleting Keyfobs
To delete a keyfob, press when the display
shows ‘Delete User' in the 'CHANGE CODES' menu.
Learning Procedure.
KF4-WE
Press and hold any button on
the keyfob until the RED and
GREEN LEDs flash, then
release.
Press 
Enter Master Manager Code
Press 
In
D
ay Mode
Enforcer 32-WE
Time 8:30am c
Enter Your Code
[******]
Press 
SET DATE & TIME?
CHANGE CODES?
Press 
Add New User?
Press 
Enter name, Press 
Use [or ]. Press 
Use [or ]. Press 
Empty [02]
Enter user code
[ ]
User Name
_
Select Button
Lock [1]
Button Action[2]
Set Area

Enforcer 32-WE Wireless Setup Manual
Page: 9
5. Deleting Inputs and Bells
Deleting Inputs and Bells from the Enforcer 32-WE can either be done collectively or individually.
Deleting Inputs Deleting Bells
In the En
g
ineer Men
u
Use andto scroll to:
Enter 
Press 
Press 
Press 
WIRELESS DEVICE
CONTROL?
Control Inputs?
Press 
Learn Devices?
Delete Devices?
Press to delete
individually
Delete All?
Press 
Input(s) deleted
Input 01
Learnt [01]
Enter Your Code
[ ]
Inputs Deleted
In the Engineer Menu
Use andto scroll to:
Enter 
Press 
Press 
Press 
WIRELESS DEVICE
CONTROL?
Control Inputs?
Control Bells?
Press 
Press 
Learn Devices?
Delete Devices?
Press to delete
individually
Delete All?
Press 
Bell(s) deleted
Select Bell
Learnt [01]
Enter Your Code
[ ]
Bells Deleted

Enforcer 32-WE Wireless Setup Manual
Page: 10
6. Diagnostics
The diagnostics function shows all wireless input and bell signal strengths and battery status.
6.1 Signal Strength
One of the most important factors for a reliable wireless
installation is the signal strength between a wireless
device and the panel. If a device is out of range it will not
be able to send events to the Enforcer 32-WE panel
therefore it is recommended that a signal strength test is
performed before fixing devices into place.
The Enforcer 32-WE has an advanced signal strength
mechanism that operates by monitoring all inputs/bells
after 5 minutes from the start of the test. It will perform
this test every 16 seconds.
NOTE: When performing a signal strength test it is
recommended that the system is tested in the ‘worst case
scenario’ for example with all doors and windows closed.
Once the function is entered, a count down from 300 will
begin, when 0 is reached the input results display will be
shown, or press during the countdown to go to the
input display immediately.
One of the following will be displayed:
Result Action
-No device installed
?Waiting for device signal strength information
0Missing (reposition and retest)
1Weak signal (reposition and retest)
2Good install position
3Excellent signal
The signal strength can also be read from the wireless
device LEDs:
GREEN LED = Good.
RED LED = Bad
When the display is showing the input status, pressing
will show each individual input and a detailed signal
strength reading will be shown as follows:
Result Action
Excellent [50 to 100] OK to install
Good [30 to 49] OK to install
Weak [0-29] Not OK to install
Missing [-] Not OK to install
Signal Strength Procedure.

Enforcer 32-WE Wireless Setup Manual
Page: 11
6.2 Battery Status
The diagnostics function also monitors the battery
of each of input and bell so that any batteries that
need replacing can be easily identified.
The Enforcer 32-WE has an advanced battery test
mechanism that operates by monitoring all
inputs/bells after 5 minutes from the start of the
test. It will perform this test every 16 seconds.
Once the function is entered, a count down from
300 will begin. Press to go to the main display,
one of the following will be displayed:
Testing = Waiting for a battery result
Good = At least one month of battery life
remaining
Replace = Battery needs to be replaced
immediately
Battery Status Procedure.
Press 
Press 
Bell [1]
No Signal [000]
Battery?
Press 
Press 
Inputs?
Please Wait
300
Input [01]
Good
Use [or ]. Press 
Bells?
Press 
Bell [1]
Good
Press 
Input [01]
Excellent [100]
Press 

Enforcer 32-WE Wireless Setup Manual
Page: 12
7. Wireless Functions
7.1 Site Options
In 'SITE OPTIONS' function there are 3 functions
for the Enforcer 32-WE:
Set With Polling Fault: This allows the Enforcer
32-WE to set even if a device has missed 20
minutes worth of device polls.
[0] No [1] Yes
Fob Unset Entry: If this function is enabled a
keyfob can only be used to unset the control panel
when the entry time is counting down.
[0] No [1] Yes
Wireless Bell Supervision: If this function is
enabled, the bell performs its own supervision and
jamming protection, and will alarm if either
condition occurs (this cannot be silenced by the
panel). The alarm will stop after the bell expiry
time, when the jamming stops or when a
supervision message has been received by the
panel. If this function is disabled, it will work the
same way as an input. No supervision or jamming
will be detected by the bell, but the Enforcer 32-
WE will still detect both depending on the timers.
[0] No [1] Yes
7.2 Change Timers
In 'CHANGE TIMERS' there are 2 functions for the
wireless operation:
Wireless Supervision Time: This is the time
window before a supervision fault will be signalled.
For example: if the time is set for 2 hours, then
any device that doesn’t communicate with the
Enforcer 32-WE within that period will cause a
supervision fault.
[0-99] hours (0=supervision faults ignored)
NOTE: Must be set to 2 hours or less to comply
with EN50131.
Wireless Jamming Time: This is the time window
that monitors the signals of each wireless device. If
a signal is ‘blocked’ for longer that the
programmed time a fault will be displayed. [0-100]
seconds (0=jamming faults ignored). NOTE: It is
not recommended to program less than 10
seconds. Must be set to 30 seconds or less (but not
to zero) to comply with EN50131.
In the Engineer Men
u
Use andto scroll to:
Press 
Press 
Use [or ]. Press 
SITE OPTIONS?
Set with Poll FL
No [0]
Fob Unset Entry
No [0]
Use [or ]. Press 
Wirls Bell Sprv
No [0]
In the En
g
ineer Menu
Use andto scroll to:
Press 
Enter Value. Press 
CHANGE TIMERS?
Wirls Sprvn Time
[02]
Wirls Jmmng Time
[030]
Enter Value. Press 

Enforcer 32-WE Wireless Setup Manual
Page: 13
8. Fault Displays
8.1 Wireless Mismatch
If an input is assigned as a type (Final exit, Intruder, etc) but no
wireless detector has not been learnt on that input number or vice
versa, this fault will be displayed.
8.2 Wireless Tamper
If a wireless input is in tamper, the alarm will activate and the input
in fault will be displayed.
8.3 Battery Low
The Enforcer 32-WE monitors the batteries of each wireless device and is defined by the following
displays:
Battery Low UXX (U = Keyfobs. XX = User Number)
Battery Low IXX (I = Inputs. XX = Input Number)
Battery Low BXX (B = Bell. XX = Bell Number)
If battery low is displayed it is advisable to replace the battery within 28 days of this message being
shown.
8.4 Wireless Supervision
The Enforcer 32-WE monitors the operation of each wireless device
and is defined by the following:
Radio Supervision IXX (I = Input, XX = Input Number)
Radio Supervision BXX (B = Bell, XX = Bell Number)
If this occurs it would be advisable to check the signal strength of the device in the diagnostics
function.
8.5 Jamming
This is reported when a jamming signal is recognised on the
wireless frequency.
Check that no wireless interference is in close proximity to the radio
devices/panel.
8.6 Wireless Poll Fault
This is displayed when no ‘polls’ are received for 20 minutes before
the set operation. Test the signal strength / battery on each
wireless device.
Wirls mismatch
Input 01
Alarm Silenced
Input 01
User
Battery Low V05
Input 02
Wirls Supervn F1
Office
Wireles Jam WZm
Input 01
Wirls Poll F700

Enforcer 32-WE Wireless Setup Manual
Page: 14
9. Wireless Peripherals
This section describes most of the wireless peripherals that can be learnt to the Enforcer 32-WE.
9.1 MC1MINI-WE
The MC1MINI-WE is a Two Way wireless magnetic contact with 1 reed switch.
9.1.1 Learning / Diagnostics / Installation
9.1.2 Installation Notes
It is recommended the MC1MINI-WE is learned at the control panel. A signal strength test should
then be performed to make sure the most suitable location is chosen, ensuring optimum wireless
range.
9.1.3 Installation Surfaces
NOTE: The MC1MINI-WE can be mounted on typical building materials; such as wood, PVC, brick
or metal etc. If you do encounter any problems with different surfaces, please contact
[email protected]
WIRELESS DEVICE
CONTROL?
Learn Devices?
Control Inputs?
Input 01
Available [01]
Learning...
LEARN
START
>5s
Input Learnt!
DIAGNOSTICS?
View Wireless
Device Status?
Signal Strength?
Inputs?
333333----------
----------------
5s
≤300s
LEDs
LEDs
No. 6.
Pan Head
Screw
CHANGE INPUTS?
Input [01]
Input 01
Input Type [07]
Final Exit
Input Active In
[ABCD]
>10m
10m

Enforcer 32-WE Wireless Setup Manual
Page: 15
9.1.4 Technical Specification
Battery: Type: 3.0V CR123A. Threshold: 2.5V +/- 5% at 25°C. Life: Up to 2 years
Wireless: Transmission Frequency: 868MHz, FM transceiver narrow band
Transmission Method: Fully encrypted rolling code
Materials and Environment: Colour and Casing: White. 2mm ABS.
Indication: LEDs (Signal, Alarm, Tamper)
Temperature: Storage:-20°C to 50°C. Certified:-10°C to 40°C Nominal:-10°C to 50°C
Dimensions (H x W x D): 27 x 104 x 25mm. Magnet: 14 x 49 x 16mm
9.1.5 Magnet Detection Performance

Enforcer 32-WE Wireless Setup Manual
Page: 16
9.2 MC2-WE
The MC2-WE is Two Way Wireless magnetic contact / universal transmitter with 2 reed / 1 input and
tamper input.
9.2.1 Learning / Diagnostics / Installation
9.2.2 Installation Notes
It is recommended the MC2-WE is learned at the control panel. A signal strength test should then
be performed to make sure the most suitable location is chosen, ensuring optimum wireless
range.
9.2.3 Installation Surfaces
NOTE: The MC2-WE can be mounted on typical building materials; such as wood, PVC, brick or
metal etc. If you do encounter any problems with different surfaces, please contact
[email protected]
LEARN WIRELESS
DEVICES?
Learn Devices?
Control Inputs?
Input 01
Available [01]
Learning...
Input Learnt!
CHANGE INPUTS?
Input Type [07]
Final Exit
Input Active In
[ABCD]
LEARN
DIAGNOSTICS?
START
View Wireless
Device Status?
Signal Strength?
Inputs?
3---------------
----------------
LEDs
LEDs
T C Z
T C Z
TA MP E R A L A R M
N/CN/C
NOTE: The use of external inputs will make the
system unable to comply with EN50131-1
S2
Enable
S1
Enable
S2
Enable
S1
Enable
Input [01]
Input 01
>10m
>5s
5s
≤300s
10m

Enforcer 32-WE Wireless Setup Manual
Page: 17
9.2.4 Magnet Detection Performance
9.2.5 Technical Specification
Battery:
Type: 3.0V CR2 Lithium Battery. Threshold: 2.5V +/- 5% at 25°C. Life:Up to 2 Years
Wireless:
Transmission Frequency: 868MHz, FM Transceiver Narrow Band
Transmission Method: Fully encrypted rolling code
Transmission Range: 1.6km free space
Materials and Environment
Colour and Casing: White (or Brown: MC2BROWN-WE). 2mm ABS
Indication: LEDs (Signal, Alarm, Tamper)
Temperature: Storage:-20°C to 50°C. Certified:-10°C to 40°C. Nominal:-10°C to 50°C
Dimensions (H x W x D): 115 x 36 x 30mm. Magnet: 56 x 13 x 17mm
Front and rear tamper.
2 reed switches, 1 external input and 1 external tamper input.
NOTE: The use of external inputs will make the system unable to comply with EN50131-1.

Enforcer 32-WE Wireless Setup Manual
Page: 18
9.3 MC1SHOCK-WE
9.3.1 Installation Notes
It is recommended the MC1SHOCK-WE is learned at the control panel. A signal strength test
should then be performed to make sure the most suitable location is chosen, ensuring optimum
wireless range.
9.3.2 Installation Surfaces
NOTE: The MC1SHOCK-WE can be mounted on typical building materials; such as wood, PVC,
brick or metal etc. If you do encounter any problems with different surfaces, please contact
[email protected]
LEARN WIRELESS
DEVICE?
Learn Inputs?
Learn Devices?
Input 01
Available [01]
Input 02
Available [02]
Input 01
Available [01]
Learning...
Input Learnt !
LEAR N
LEARN
LEAR N
No 8
countersun k
self tapping
screw
Input Learnt !
>5s
LEAR N
LEAR N
LEAR N
START
>5s
10m
PROGRAM INPUTS?
Input [01]
Input 01
Input Type [07]
Final Exit
Input Areas
[ABCD]
Input Areas
Any [0]
PROGRAM INPUTS?
Input [01]
Input 02
Input Type [07]
Intruder
Input Areas
[ABCD]
Input Areas
Any [0]
END
DIAGNOSTICS?
Wireless Range &
Battery Status?
Signal Strength?
Wireless Inputs?
3---------------
----------------
5s
≤300s
LEDs
LEDs
No. 6.
Pan H ead
Screw
=
HIGH
ALARMTA M P ER

Enforcer 32-WE Wireless Setup Manual
Page: 19
9.3.3 Magnet Detection Performance
9.3.4 Technical Specification
Battery:
Type: 3.0V CR123A Lithium Battery. Threshold: 2.5V +/- 5% at 25°C. Life: Up to 2 Years
Wireless:
Transmission Frequency: 868MHz, FM Transceiver Narrow Band
Transmission Method: Fully encrypted rolling code
Materials and Environment
Colour and Casing: White. 2mm ABS
Indication: LEDs (Signal, Alarm, Tamper). GREEN=MC. RED=SHOCK.
Temperature: Storage:-20°C to 50°C. Certified:-10°C to 40°C. Nominal:-10°C to 50°C
Dimensions (H x W x D): 30 x 115 x 35mm. Magnet: 17 x 56 x 12.7mm
Compatible with the Enforcer 32-WE, PCX and EURO control panels (Enforcer 32-WE wireless
expander only).
Front and rear tamper. 1 external input & 1 external tamper input (normally closed).
NOTE: The use of external inputs will make the system unable to comply with EN50131-1.
Spacers available if required: MC1S/SPACER-WE and MC1S/SPACERB-WE.
26mm
24mm
23mm
20mm
24mm
22mm
14mm
14mm
13mm
13mm
22mm
20mm
19mm
17mm
11mm
9mm
13mm
13mm
12mm
12mm

Enforcer 32-WE Wireless Setup Manual
Page: 20
9.4 KX12DT-WE
NOTE: All Two Way wireless detectors learn the same way as shown below.
WIRELESS DEVICE
CONTROL?
Learn Devices?
Control Inputs?
Input 01
Available [01]
Learning
LEARN
>5s
Input Learnt!
DIAGNOSTICS?
View Wireless
Device Status?
Signal Strength?
Inputs?
3---------------
----------------
5s
≤300s
LEDs
HIGH
LOW
LEDs
0.25 - 2.5m/s
0.25 - 2.5m/s
12m
12m
12m
0m
2.4m
CHANGE INPUTS?
Input Type [07]
Final Exit
Input Active In
[ABCD]
Input [01]
Input 01