Telikou SKYLINE SK-100 User manual

TELIKOU®Intercom System
SKYLINE SK-100 / SK-190 Wireless Intercom
Instruction Manual
© TELIKOU Systems
All Rights Reserved

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
1
I. INTRODUCTION
Thank you for choosing TELIKOU SKYLINE series wireless intercom products.
1. This system consists of 1x SK-100 main station, max 4x SK-100ANT antenna(RJ45 connector),
Max 16x SK-190 wireless belt packs.
2. SK-190 belt pack can roam among different antennas. If the belt pack walks out of the antenna
signal range, it will sound a cue.
3. SK-190 belt pack can roam to another antenna manually .
4. All the SK-190 belt packs under one antenna form a party line group. In this group, everyone can
talk to each other.
5. When SK-100 main station turns on a certain TALK button, all belt pack screens corresponding
are awakened to listen to the base station.
6. When TALK button on main station is OFF, if a belt pack turns on the MIC button. The LED
above TALK button flashes. After pressing the TALK button, it enters a full duplex conversation.
If the main station turns on other channels at this time, they will all join the call.
7. After conversation, when the TALK button on main station is turned off , the corresponding belt
pack MIC will also be turned off at same time.
II. Main Station
Main station is the control unit for the whole wireless system. It talks with the corresponding group of
any antenna through the button switch on front panel. It also can sent program audio, 2-Wire and
4-Wire audio to the system. When the active antenna is less than 200 meters away from the base
station, the power is supplied by the base station; otherwise, the power is supplied by the local 24V
or the USB port 5V.
Front Panel
1#天线 2#天线 3#天线 4#天线
4 ON 3 INT 4 OFF
频率1.8GHz 音量
1. Headset
XLR-5M Pin definition：
Pin 1 -- Mic-
Pin 2 -- Mic+
Pin 3 -- Ear-
Pin 4 -- Ear+
Pin 5 -- Ground

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
2
2. Panel Gooseneck Microphone
4 Pin Aviation Pin definition：
Pin 1 -- Mic-
Pin 2 -- Mic+
Pin 3 -- Ground
Pin 4 -- Null
3. Volume / Menu Control knob
Rotary encoder with switch. The rotary encoder is used to adjust the volume of the base station
headphones, with a total of 16 choices. When the switch is pressed for more than 3S, the base
station enters the setting function.
4. All Button
Press this button will turn on or off all the channel.
5. Channel Button (TALK) and Indicator LED
Each button corresponds one antenna group. For example, press channel 1 button to talk with
belt packs which under antenna 1. In standby mode, if press MIC button on belt pack, the LED
above corresponding channel button will flash. Press channel button to enter full duplex model.
If more than one channel button is pressed, these groups make a big communication group.
When the base station turns off the channel button after the call, the belt pack MIC button
corresponding is also turned off at the same time.
6. LCD screen
Hold Volume/Menu knob more than 3s, main station enter setting menu. By rotating the
Volume/Menu knob, the cursor will move between options, and the cursor will stop at a certain
option, press the knob once to enter the option. Rotate the knob clockwise and anticlockwise to
select the value of this option and return to the previous menu. In the top menu, select
“Save&Exit” or “Exit” to exit the setting function.
LCD screen display content under working status
First Line : The name of antenna
GP1 GP2 GP3 GP4
Second Line : The number of registered belt packs and the status of Aux In.
If antenna is not connected, this line is blank.

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
3
The Settings
Language : English or Chinese
MIC Select : Headset - Panel microphone and panel speaker do not work.
Panel MIC - Headset microphone does not work. Earphone volume drops
6dB.
MIC Gain : Change panel microphone gain. It has total 16 levels.
Local Side tone : Adjust the microphone level which sent back to panel speaker. It has total
16 levels.
AUX. Audio : There are four antenna groups to select. After select, there are three model to
select.
On : Aux audio in is enable
OFF : Aux audio in is disable
INT : When channel button is disable, the aux audio in is enable;
When channel button is enable, the aux audio in is disable.
Tally : Screen shows Tally 1 - Tally 4 four tally signal. Choose any signal, screen
shows belt pack 1 to belt pack 16. Then assign the selected tally signal to
this belt pack.
Frequency : Select system working frequency
Save&Exit : Save change and exit setting
Exit : Without save any change and exit setting
7. AUX. In
Allows auxiliary audio input to system. The green LED above lights constantly.
8. AUX In Level Adjustment
Adjusts the auxiliary audio level input
9. 4-Wire
Allows external 4-wire audio input to system. The green LED above lights constantly

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
4
10. 4-Wire Level Adjustment
Adjust the 4-wire audio level input
11. 2-Wire
Allows external 2-wire audio input to system. The green LED above lights constantly
When receives call signal, the green LED above flashes.
12. ANN. Out
Press and hold the button to sent microphone signal to ANN.out connector. The LED above
lights. The internal relay pull in. The relay connector at rear panel status changes. Release the
button, relay returns to its original state.
13. Panel Speaker
8ohm / 2W speaker
Rear Panel
1#天线 2#天线 3#天线 4#天线
4 ON 3 INT 4 OFF
频率1.8GHz 音量
1. Power Connector
AC 90V~260V, 50-60Hz
2. DB-9 Data Connector
This DB-9 connects switcher Tally output. It receives four dual color tally signal and can be
assigned to any belt pack you want.
Pin definition:
Pin 1 --- Tally 1 Green
Pin 2 --- Tally 1 Red
Pin 3 --- Tally 2 Green
Pin 4 --- Tally 2 Red
Pin 5 --- Tally 3 Green
Pin 6 --- Tally 3 Red
Pin 7 --- Tally 4 Green
Pin 8 --- Tally 4 Red

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
5
3. Relay Connector
6.35mm / 1/4 inch connector. When ANN.Out button is pressed, this relay is closed.
R: Normally Closed Contact
T: Moving Contact
S: Noormally Open Contact
4. ANN. Out
Base station microphone output.
XLR-3M connector:
Pin 1 --- GND
Pin 2 --- Audio Out +
Pin 3 --- Audio Out -
5. 4-Wire Connector
Audio in and Audio out connector. Audio level is 1Vp-p
RJ-45 Connector:
Pin 1 --- GND
Pin 2 --- 12VDC
Pin 3 --- Audio In +
Pin 4 --- Audio Out +
Pin 5 --- Audio Out -
Pin 6 --- Audio In -
Pin 7 --- NULL
Pin 8 --- NULL
6. 2-Wire Connector
XLR-3M Connector
Pin 1 --- GND
Pin 2 --- 24VDC
Pin 3 --- Audio

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
6
7. AUX. In
XLR-3F Connector, 1Vp-p audio level
Pin 1 --- GND
Pin 2 --- Audio In +
Pin 3 --- Audio In -
8. Transceiver Connector
Four RJ-45 connector to Antenna
RJ-45 Connector:
Pin 1 --- GND
Pin 2 --- 24VDC
Pin 3 --- Rx +
Pin 4 --- Tx +
Pin 5 --- Tx -
Pin 6 --- Rx -
Pin 7 --- 24VDC
Pin 8 --- GND
III Active Antenna
The signal coverage radius of the antenna in the open area is 300 meters. Each antenna can
connect up to 4 wireless belt packs.
1. Power Connector
Pin 1 --- GND
Pin 2 --- Null
Pin 3 --- Null
Pin 4 --- 24VDC

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
7
2. USB Connector
External power bank supplies 5VDC
Computer Data port
3. Antenna Sequence Number
Two digits coding switch. The number at the top of the chart is the antenna number
corresponding to different dial positions
4. Register
Belt pack should register with all antennas that belt pack may roam to.
A) Pairing Belt Pack
Press and hold the register button until the indicator flash. Belt pack enters setting menu and
selects registration. Once the indicator becomes solid, it means that the pairing process is
completed. Antenna backs to normal working mode.
B) Delete Belt Pack
Make sure all the belt packs which are paired with this antenna is turned on. Press and hold
the register button until the indicator flash. Press register button 7 times will delete all the belt
pack pairing.
Note: If belt pack is not turned on before antenna deletes belt pack pairing. This belt pack
must pairing again with same antenna otherwise this belt pack can not work properly.
Or this belt pack must be reset before use.
5. Power and Registration Indicator
After power on, the indicator light is always on. When the antenna enters the registration
state, the indicator flashes slow (1s). After pairing finished, the indicator light becomes
always on.
6. Active Antenna Connector
E1 connector. Antenna connects to base station through CAT5 cable.
Pin 1 --- GND
Pin 2 --- 12VDC
Pin 3 --- Audio Input +
Pin 4 --- Audio Output +
Pin 5 --- Audio Output -
Pin 6 --- Audio Input -
Pin 7 --- Control Signal
Pin 8 --- Control Signal

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
8
橙白
橙
绿白
蓝
蓝白
绿
棕白
棕
橙白
橙
蓝
绿白
绿
蓝白
棕白
棕
屏蔽 屏蔽
1 8 0 0 1 8
Orange White
Orange
Green White
Blue
Blue White
Green
Brown White
Brown
Orange White
Orange
Blue
Green White
Green
Blue White
Brown White
Brown
Shield Shield
7. SMA Antenna Connector
Two SMA connectors
IV. Belt Pack
SKYLINE-190 belt pack uses 4x AA battery. Rechargeable battery can be charged through micro-
USB connector. In the multi-antenna signal coverage area, belt pack can manually switch to
different registered antenna. When walk over the antenna coverage, belt pack headset gives
warning sound.
Belt pack is in standby mode after power on. When there is an external call, it will be answered
automatically. When press Mic button, it will make a full duplex communication.

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
9
1. Power Button and Volume Adjustment
With switch encoder. Turn it clockwise or anti-clockwise to adjust earphone audio volume. There
Is 16 levels to select. If hold button more than 5s, the belt pack is turned on or off.
2. Mic Button
Touch button with two operating mode
PTT: Push to talk
Latch:
3. Tally Light Connector
3.5mm connector
4. Micro-USB Connector
Charging port. If the belt pack has a Ni-MH/Ni-Cd rechargeable battery, you can connect a 5v
adapter to charge it.
5. Headset Connector
XLR-5M connector

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
10
Pin 1 --- Mic -
Pin 2 --- Mic +
Pin 3 --- Ear -
Pin 4 --- Ear +
Pin 5 --- GND
6. ISO Button
Press and hold the button. The belt pack makes an isolated conversation with ISO target belt
pack. Release the button, the ISO conversation is finished.
7. LCD Screen
Display content:
Registered antenna number, Current working antenna number and Signal field
strength
Battery Power
Working Frequency
Belt Pack Label (BP-1, BP-2, BP-3, BP-4,BP-5, BP-6,...,BP-16 )
ISO Target Label ( ISO: Null, BP-1, BP-2, BP-3, BP-4,BP-5, BP-6,...,BP-16)
Setting Menu
Hold the Mic button and press power button will enter setting menu. LCD screen displays
menu. Rotate the power and volume encoder to move the cursor. When the cursor is on an
option, press the power and volume encoder to enter the option. Rotate the power and
volume encoder to Change parameters.
Language: English or Chinese
ISO Set: Base and other belt packs which under same antenna
Mic Gain: Volume 1 ~ Volume 16
Frequency: select 1.8G or 1.9G first, then select country or area.
Registration: Register belt pack to antenna
Label: BP-1, BP-2, BP-3, BP-4,BP-5, BP-6,...,BP-16
Reset: When the belt pack can not work normally due to problems such as registration,
you can use this function to clear the registration information and restore the factory
settings.
Save&Exit: Save change and exit
Exit: Exit without save any change
8. Roaming
Every belt pack can be paired with four antennas. Belt pack shows the antenna number (1-4)

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
11
which are already paired on LCD screen. Belt pack can roam among these antennas. Press and
rotate the power and volume encoder can switch antenna manually.
V Technical Parameters
1. Power: 4xAA Battery or 4xAA Rechargeable Battery
2. Standby Time: Over 72 hours
3. Working Time: Over 10 hours
4. Charging: Micro-USB 5VDC
5. Frequency
1.8G Channel
Channel
Transmit
Receive
0
1897.344
1897.344
1
1895.616
1895.616
2
1893.888
1893.888
3
1892.160
1892.160
4
1890.432
1890.432
5
1888.704
1888.704
6
1886.976
1886.976
7
1885.248
1885.248
8
1883.520
1883.520
9
1881.792
1881.792
1.9G Channel
Channel
Transmit
Receive
0
1921.536
1921.536
1
1923.264
1923.264
2
1924.992
1924.992
3
1926.720
1926.720
4
1928.448
1928.448
6. DECT 1.8G RF unit test
Parameter
Nominal
Limit
Unit
TX POWER
22
≧18
dBm
Frequency OFFSET (Use FIG31 patter)
f © +/- 0
± 50
KHz
Freq deviation
(FIG31) B FIELD
CH5
360
±30
KHz
The other
360
300—400
KHz
Frequency drift
PCBA
0
± 15
KHz/slot
Receive sensitivity (@BER < 1000ppm
-94
≤-90
dBm
Timing Fitter
0
5
ppm
RSSI @ RF CH5 & RF Level –50dBm
TBD
TBD
V
Reference clock
13.824000
±0.000010
MHz

TELIKOU SKYLINE SK-100 / SK-190 Wireless Intercom
12
7. DECT 1.9G RF unit test
Parameter
Nominal
Limit
Unit
TX NTP for PCBA
20
± 2
dBm
Frequency OFFSET (Use FIG31 patter)
f © +/- 0
± 50
KHz
Freq deviation (FIG31)
B FIELD
DATA:
360KHZ
For ATE:
320-400 (AT
CH2)
KHZ
Frequency drift (PCBA)
0
± 20
KHz/slot
Receive sensitivity (@BER < 1000ppm
-94
<= -90
dBm
Timing Fitter
0
+/- 5
ppm
RSSI @ RF CH5 & RF Level –50dBm
TBD
TBD
V
8. Size
SK-100 Base Station: 480 x 255 x 45mm
SK-100 Antenna: 135 x 130 x 50mm(without antenna), 165 x 130 x 200mm(with antenna),
SK-190 Belt Pack: 105 x 90 x 35mm
9. Weight
SK-100 Base Station: 2KG
SK-100 Antenna: 0.45KG
SK-190 Belt Pack: 0.12KG (without battery)