Telme2 BH-X User manual

1
User Guide
Hi-Fi Bluetooth stereo headset
BH-X from Telme2
Thanks for choosing this fine headset from Telme2. We hope you will
enjoy the use. Please read this short User Guide before use.
Introduction
This comfortable headset uses the newest aptx technology providing you
with excellent stereo sound. You may enjoy this headset for listening to
music from a variety of Bluetooth sources, including the unique TosBlue-
X and TosBlue-X2 from Telme2. You may also make hands-free phone
calls from your smartphone via this headset, as the headset is equipped
with a microphone.
Warning
The headset must not be exposed to excessive heat or moisture as the
internal battery may be damaged.
Overview
1
Retractable headband
2
Previous track button
3
Next track button
4
LED in indicator –blue & red
5
Power ON/OFF/Pairing button
6
Volume up button
7
Volume down button
8
Charging jack

2
9
Microphone for phone calls
Wearing the headset
With its big ear pads and the retractable headband, the headset is
comfortable to wear. Please adjust the headband extension for your best
comfort. For correct sound distribution, please note that the headset is
marked with “R” for right, and “L” for left. Please wear it accordingly.
Charging the headset
Before use the first time, the headset must be fully charged. This will take
about 2 hours.
Connect the included USB-cable to a live USB outlet and into the
headset. The red LED indicates charging. When light goes out, charging is
completed.
Pairing the headset for the first time
The headset may be paired with a Bluetooth transmitting device with
A2DP profile of your choice. Do this:
-First you should set this BH-X headset in pairing mode by pressing the
ON/OFF/Pairing button for 6 - 8 seconds or until the red and blue lights
are alternately quickly flashing.
- Then, set the Bluetooth transmitting device into “Searching Pairing
Mode”. (See User Guide for instructions).
NOTE: it is recommended to do the pairing in this sequence.
-Release the button.
The headset will now pair with the transmitting device and will be ready
for use. This is indicated by the LED flashing blue every once or twice
every 8 seconds.
NOTE:
If PIN is requested, type 0000.
NOTE:
If pairing is not made within 2 minutes, the headset will go into
standby mode.

3
Power OFF
-Press the ON/OFF/Pairing button for 3 - 5 seconds or until the
LED is flashing red 3 times. Release the button. When the
headset is turned OFF, the LED becomes dark.
Pairing with the same Bluetooth transmitting devices the
following times
Every time you turn the headset ON –and the Bluetooth transmitting
device is turned ON –the headset will automatically be reconnect. The
headset remembers the last 8 paired devices.
When reconnected, the LED flashes once blue quickly every 8 seconds.
NOTE:
If for some reason the headset has not paired –connected within 5
minutes, it will turn itself OFF to save power.
Power ON
Press the ON/OFF/Pairing button for about 3-5 seconds or until the LED
flashes quickly blue 4 times.
Pairing with TosBlue-X
One BH-X may be connected to TosBlue-X. The procedure is
simple.
Pairing for the first time
Important: The pairing must take place within the 2 first minutes
after power On of TosBlue units, and during the ”Pairing Search
Mode”. (Red and blue LED flashing rapidly)
Do this:
- Press the ON/OFF/Pairing button of the headset for 6 - 8
seconds or until the red and blue lights are alternately quickly
flashing.
-Release the button.
The headset will now be pair and will be ready for use indicated by
the LED flashing blue every once or twice every 8 seconds.

4
Connecting the following times
Any time after the TosBlue-X has entered the “Ready Mode” (red
and blue LED flashing slowly),
-you turn the headset ON –and connection takes place
automatically.
Pairing with TosBlue-X2
Two BH-X headsets may be connected to a TosBlue-X2 units at the
same time, so 2 persons may enjoy listening to a TV program
simultaneously.
To pair with TosBlue-X2 the first time
Do this:
-Pair the first headset as described above
-Then turn power OFF
-Pair the second headset as you did for first headset
-Turn ON the second headset –and it will automatically
pair.
Both headsets should now be connected to the TosBlue-X2
unit.
Connecting with TosBlue-X2 the following times:
Any time while the TosBlue-X2 is in “Ready Mode” (more than
2 minutes after power is applied), the headsets may
reconnect.
Do this:
-Turn power ON the first headset. It will connect
-Turn power ON the second headset. It will connect

5
Important NOTE l: If the TosBlue unit is attached to a TV with
included Bluetooth devices, the pairing process may be blocked.
If this happens, enter the pairing process on the BH-X headset
first; thereafter turn on the TV and the TosBlue unit –in this
sequence.
Important NOTE ll: If pairing problem persists after trying above
note, a software hang-up may have occurred.
To reset the software, try this:
Press and hold the a) Power On button and b) the “ –“ buttons
simultaneously for about 8 seconds and until you see the red and
blue light flashing.
Adjusting the volume
You may at any time adjust the volume up or down by use of the 2
volume buttons.
Next track/Previous track
While listening to music from a Bluetooth device supporting AVRCP
(Audio/Video Remote Control Profile), you may maneuver to the “next
track” or the “previous track” using the 2 control buttons on the headset.
Hands-free Call
While connected to a mobile phone, you may make or receive hands-free
phone calls as the headset has built in microphone.
For your convenience, we recommend that you accept the phone call via
the control buttons on the mobile phone.
NOTE:
If you are listening to music when receiving a phone call, the music
will automatically fade out and the conversation fades in. When
completing the phone call, the music will fade back in.

6
Low power warning
When the red LED start flashing twice every 30 seconds and you hear a
“Dong-Dong-Dong”sound, then your headset is ready for recharging.
LED information
Charging
Steady red
OFF/End Charging
No light
During pairing
sequence
Rapid alternately flashing red and blue
Power ON sequence
4 rapid blue flashes
Power OFF sequence
4 rapid blue flashes
ON - connected to a
non –aptx device
Flashing blue quickly once every 8 seconds.
ON –connected to a
aptx device
Flashing blue quickly twice every 8 seconds
ON –in standby –not
connected to a device
Blue flashes quickly twice every 2 seconds
Incoming call
Blue LED flashes quickly
During call
Blue Led flashes once every 2 seconds
Low battery
LED flashes red twice every 30 seconds + a
“Dong-Dong” sound.
Other functions:
LED light OFF function
If you feel the LED light is visually disturbing –and you want to conserve
some power - you may turn the LED light OFF during operation. Do this:
Press the “previous track” and the “next track buttons at the same time
and hold for about 5 seconds. The LED will be turned OFF. Do the same
to turn the LED back ON.
NOTE:
The next time you use the headset, the LED will work normal
again.
Multi-pairing
The headset may connect to 2 devices at the same time, for example a
mobile phone supporting the HFP profile and a device supporting the
A2DP profile. Do this:

7
a) Pair with the A2DP transmitter device
b) Turn the A2DP device OFF
c) Pair with the HFP device –the mobile phone
d) Turn ON the A2DP transmitter device. This device will now pair
automatically.
NOTE:
The devices will remember each other and will automatically
reconnect next time they are turned ON.
Microphone mute
We recommend muting the microphone on the mobile. However,
it is possible to do the mute on the handset. Then do this:
-Press quickly the ON/OFF/Pairing button twice. The
microphone should now be muted.
---0---