Teltonika FMB130 Installation guide

FMB130
Advanced tracker with
flexible inputs configuration
Quick Manual v1.5

Quick Manual v1.5 // FMB130 2
CONTENT
Know your device................................................................................................................................................................................................3
Pinout ...................................................................................................................................................................................................................4
WIRING SCHEME .................................................................................................................................................................................................5
Set up your device ..............................................................................................................................................................................................6
PC Connection (Windows)..................................................................................................................................................................................7
How to install USB drivers (Windows) ..............................................................................................................................................................7
Conguration.......................................................................................................................................................................................................8
Quick SMS conguration................................................................................................................................................................................. 10
Mounting recommendations.......................................................................................................................................................................... 12
Basic characteristics ........................................................................................................................................................................................ 13
LED indications................................................................................................................................................................................................. 13
Electrical characteristics.................................................................................................................................................................................. 16
Safety information .......................................................................................................................................................................................... 18
Certication and Approvals ............................................................................................................................................................................ 19
Warranty ........................................................................................................................................................................................................... 20
Warranty disclaimer ........................................................................................................................................................................................ 20

Quick Manual v1.5 // FMB130 3
KNOW YOUR DEVICE
2X6
SOCKET
STATUS
LED
MICRO SIM
SLOT
BATTERY
SOCKET
NAVIGATE
LED
MICRO
USB
TOP VIEW TOP VIEW (WITHOUT COVER)BOTTOM VIEW (WITHOUT COVER)

Quick Manual v1.5 // FMB130 4
PIN NUMBER PIN NAME DESCRIPTION
1VCC (10-30) V
DC (+) Power supply (+10-30 V DC).
2 DOUT 3
Digital output, channel 3.
Open collector output. Max.
0,5 A DC..
3DIN 3 / AIN 2
Analog input, channel 2.
Input range: 0-30 V DC /
Digital input, channel 3.
4DIN 2-N /
AIN 1
Digital input, channel 2,
Negative input, Analog input,
channel 1, Input range: 0-30
V DC.
5 DIN 1 Digital input, channel 1.
6 INPUT 6 TX EXT (LVCAN – TX).
7 GND (-) Ground pin. (10-30) V DC (―)
8 DOUT 1
Digital output, channel 1.
Open collector output. Max.
0,5 A DC..
9 DOUT 2
Digital output, channel 2.
Open collector output. Max.
0,5 A DC.
10 1WIRE POWER +3,8 V output for 1–Wire
devices.
11 1WIRE DATA Data for 1–Wire devices.
12 INPUT 5 RX EXT (LVCAN - RX).
PINOUT
DOUT2
1WIRE POWER
1WIRE DATA
GND
DOUT1
INPUT 5
DIN3/AIN2
DIN2-N/AIN1
DIN1
DOUT3
+10...30 V DC
INPUT 6
10
9
8
7
11
12
4
3
2
1
5
6
FMB130 2x6 socket pinout

Quick Manual v1.5 // FMB130 5
WIRING SCHEME
BUZZER
30
8586
87a
87
IGNITION
DETECTION
FUEL GAUGE
STARTER
IBUTTON
POWER SUPPLY
10 - 30V DC
ANALOG
LLS SENSOR
CAN-CONTROL
ALARM BUTTON
DOOR SENSOR CENTRAL LOCK
DOUT2
1WIRE POWER
1WIRE DATA
GND
DOUT1
INPUT 5
DIN3/AIN2
DIN2-N/AIN1
DIN1
DOUT3
+10...30 V DC
INPUT 6
10
9
8
7
11
12
4
3
2
1
5
6
AIN2
DIN3
DIN2
DIN2-N

Quick Manual v1.5 // FMB130 6
SET UP YOUR DEVICE
HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY
4
1COVER REMOVAL 3BATTERY CONNECTION 2MICRO-SIM CARD INSERT ATTACHING COVER BACK
Gently remove FMB130
cover using plastic pry
tool from both sides. Then
remove the top cover..
Insert Micro-SIM card as
shown with PIN request
disabled or read our Wiki1
how to enter it later in
Teltonika Congurator2.
Make sure that Micro-
SIM card cut-o corner is
pointing forward to slot.
1 wiki.teltonika-gps.com/view/
FMB130_Security_info
2 wiki.teltonika-gps.com/view/
Teltonika_Congurator
Connect battery as shown to
device. Position the battery
in place where it does not
obstruct other components.
After conguration, see “PC
Connection (Windows)1”,
attach device cover back.
1 Page 7, "PC Connection
(Windows)"

Quick Manual v1.5 // FMB130 7
PC CONNECTION (WINDOWS)
HOW TO INSTALL USB DRIVERS (WINDOWS)
1. Please download COM port drivers from here1.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the conrmation window will appear. Click Finish to complete the
setup.
1 teltonika.lt/downloads/en/FMB130/TeltonikaCOMDriver.zip
1. Power-up FMB130 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED
indications1”.
2. Connect device to computer using Micro-USB cable or Bluetooth connection:
• Using Micro-USB cable
• You will need to install USB drivers, see “How to install USB drivers (Windows)2”
• Using Bluetooth
• FMB130 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device >
Bluetooth. Choose your device named – “FMB130_last_7_imei_digits”, without LE in the end. Enter default password 5555,
press Connect and then select Done.
3. You are now ready to use the device on your computer.
1 wiki.teltonika-gps.com/view/FMB130_LED_status
2 Page 6, "How to install USB drivers"

Quick Manual v1.5 // FMB130 8
MS .NET REQUIREMENTS
Operating system MS .NET Framework version Version Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework 4.6.2 32 and 64 bit www.microsoft.com1
1 dotnet.microsoft.com/en-us/download/dotnet-framework/net462
At rst FMB130 device will have default factory settings set. These settings should be changed according to the users needs. Main
conguration can be performed via Teltonika Congurator1software. Get the latest Congurator version from here2. Congurator
operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
1 wiki.teltonika-gps.com/view/Teltonika_Congurator
2 wiki.teltonika-gps.com/view/Teltonika_Congurator_versions
CONFIGURATION

Quick Manual v1.5 // FMB130 9
Downloaded Congurator will be in compressed archive.
Extract it and launch Congurator.exe. After launch software
language can be changed by clicking 🌐 in the right bottom
corner.
Conguration process begins by pressing on connected device.
FMB130
Various Status window1 tabs display information about GNSS2,
GSM3, I/O4, Maintenance5and etc. FMB130 has one user
editable prole, which can be loaded and saved to the device.
After any modication of conguration the changes need to
be saved to device using Save to device button. Main buttons
oer following functionality:
 Load from device – loads conguration from device.
 Save to device – saves conguration to device.
 Load from le – loads conguration from le.
 Save to le – saves conguration to le.
 Update rmware – updates rmware on device.
 Read records – reads records from the device.
 Reboot device – restarts device.
 Reset conguration – sets device conguration to
default.
Most important congurator section is GPRS – where all
your server and GPRS settings6 can be congured and Data
Acquisition7 – where data acquiring parameters can be
congured. More details about FMB130 conguration using
Congurator can be found in our Wiki8.
After connection to Congurator Status window will be
displayed.
FMB130
1 wiki.teltonika-gps.com/view/FMB130_Status_info
2 wiki.teltonika-gps.com/view/FMB130_Status_info#GNSS_Info
3 wiki.teltonika-gps.com/view/FMB130_Status_info#GSM_Info
4 wiki.teltonika-gps.com/view/FMB130_Status_info#I.2FO_Info
5 wiki.teltonika-gps.com/view/FMB130_Status_info#Maintenance
6 wiki.teltonika-gps.com/index.php?title=FMB130_GPRS_settings
7 wiki.teltonika-gps.com/index.php?title=FMB130_Data_acquisition_
settings
8 wiki.teltonika-gps.com/index.php?title=FMB130_Conguration

Quick Manual v1.5 // FMB130 10
QUICK SMS CONFIGURATION
Default conguration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS SETTINGS:
 2001 – APN
 2002 – APN username (if there are no APN username,
empty eld should be left)
 2003 – APN password (if there are no APN password,
empty eld should be left)
SERVER SETTINGS:
 2004 – Domain
 2005 – Port
 2006 – Data sending protocol (0 – TCP, 1 – UDP)
« setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0»
1 2 3 4 5 6
1
2
3
4
5
6

Quick Manual v1.5 // FMB130 11
DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION: DEVICE MAKES A RECORD ON MOVING
IF ONE OF THESE EVENTS HAPPEN:
SPEED DIFFERENCE
between last coordinate
and current position is
greater than 10 km/h
VEHICLE DRIVES
100 meters
VEHICLE TURNS
10 degrees
PASSES
300 seconds
After successful SMS conguration, FMB130 device will synchronize time and update records to congured server. Time intervals
and default I/O elements can be changed by using Teltonika Congurator1or SMS parameters2.
1 wiki.teltonika-gps.com/view/Teltonika_Congurator
2 wiki.teltonika-gps.com/view/Template:FMB_Device_Family_Parameter_list
VEHICLE MOVEMENT
will be detected by
accelerometer
DEVICE MAKES A
RECORD ON STOP IF:
1 HOUR PASSES
while vehicle is
stationary and
ignition is o
IGNITION
will be detected by
vehicle power voltage
between 13,2 – 30 V
RECORDS SENDING TO
SERVER:
EVERY 120 SECOND
it is sent to the server
If device has made a
record

Quick Manual v1.5 // FMB130 12
MOUNTING RECOMMENDATIONS
CONNECTING WIRES
• Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the
wires.
• The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied
again.
• If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional
isolation should be applied.
• Wires cannot be connected to the board computers or control units.
CONNECTING POWER SOURCE
• Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in
5 to 30 minutes period.
• When module is connected, measure voltage again to make sure it did not decrease.
• It is recommended to connect to the main power cable in the fuse box.
• Use 3A, 125V external fuse.
CONNECTING IGNITION WIRE
• Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
• Check if this is not an ACC wire (when key is in the rst position, most of the vehicle electronics are available).
• Check if power is still available when you turn o any of vehicles devices.
• Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on,
may be chosen.
CONNECTING GROUND WIRE
• Ground wire is connected to the vehicle frame or metal parts that are xed to the frame.
• If the wire is xed with the bolt, the loop must be connected to the end of the wire.
• For better contact scrub paint from the spot where loop is going to be connected.

Quick Manual v1.5 // FMB130 13
BEHAVIOUR MEANING
Permanently
switched on GNSS signal is not received
Blinking every
second Normal mode, GNSS is working
O
GNSS is turned o because:
Device is not working or Device is in
sleep mode
Blinking fast
constantly Device rmware is being ashed
BEHAVIOUR MEANING
Blinking every
second Normal mode
Blinking every two
seconds Sleep mode
Blinking fast for a
short time Modem activity
O Device is not working or Device is in
boot mode
LED INDICATIONS
NAVIGATION LED INDICATIONS
STATUS LED INDICATIONS
BASIC CHARACTERISTICS
MODULE
Name Teltonika TM2500
Technology GSM/GPRS/GNSS/BLUETOOTH
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS, AGPS
Receiver Tracking: 33
Tracking sensitivity -165 dBM
Accuracy < 3 m
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s
CELLUAR
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support SMS (text/data)

Quick Manual v1.5 // FMB130 14
POWER
Input voltage range 10-30 V DC with overvoltage
protection
Back-up battery 170 mAh Li-Ion battery 3.7 V (0.63
Wh)
Internal fuse 3 A, 125 V
Power consumption
At 12V < 2.5 mA (Ultra Deep Sleep1)
At 12V < 5 mA (Deep Sleep2)
At 12V < 5.5 mA (Online Deep
Sleep3)
At 12V < 18,5 mA (GPS Sleep4)
At 12V < 34 mA (nominal with no
load)
BLUETOOTH
Specication 4.0 + LE
Supported
peripherals
Temperature and Humidity
sensor5, Headset6, OBDII dongle7, ,
Inateck Barcode Scanner, Universal
BLE sensors support
1 wiki.teltonika-gps.com/view/FMB130_Sleep_modes#Ultra_Deep_Sleep_
mode
2 wiki.teltonika-gps.com/view/FMB130_Sleep_modes#Deep_Sleep_mode
3 wiki.teltonika-gps.com/view/FMB130_Sleep_modes#Online_Deep_
Sleep_mode
4 wiki.teltonika-gps.com/view/FMB130_Sleep_modes#GPS_Sleep_mode
5 teltonika-gps.com/products/accessories
6 wiki.teltonika-gps.com/view/How_to_connect_Bluetooth_Hands_Free_
adapter_to_FMB_device
7 wiki.teltonika-gps.com/view/How_to_connect_OBD_II_Bluetooth_
Dongle_to_FMB_device
INTERFACE
Digital Inputs 3
Negative Inputs 1 1 (Digital Input 2)
Impulse Inputs 2 (Digital Input 1, Digital Input 2)
Digital Outputs 3
Analog Inputs 2
CAN Adapter inputs 1
1-Wire 1
GNSS antenna Internal High Gain
GSM antenna Internal High Gain
USB 2.0 Micro-USB
LED indication 2 status LED lights
SIM Micro-SIM + eSIM
Memory 128MB internal ash memory
PHYSICAL SPECIFICATION
Dimensions 65 x 56 x 20,6 mm (L x W x H)
Weight 55 g
OPERATING ENVIRONMENT
Operating
temperature
(without battery)
-40 °C to +85 °C

Quick Manual v1.5 // FMB130 15
Storage temperature
(without battery) -40 °C to +85 °C
Operating humidity 5% to 95% non-condensing
Ingress Protection
Rating IP41
Battery charge
temperature 0 °C to +45 °C
Battery discharge
temperature -20 °C to +60 °C
Battery storage
temperature
-20 °C to +45 °C for 1 month
-20 °C to +35 °C for 6 months
FEATURES
Sensors Accelerometer
Scenarios
Green Driving, Over Speeding
detection, Jamming detection,
GNSS Fuel Counter, DOUT Control
Via Call, Excessive Idling detection,
Immobilizer,iButton Read
Notication, Unplug detection,
Towing detection, Crash detection,
Auto Geofence, Manual Geofence,
Trip8
Sleep modes GPS Sleep, Online Deep Sleep,
Deep Sleep, Ultra Deep Sleep9
8 wiki.teltonika-gps.com/view/FMB130_Features_settings
9 wiki.teltonika-gps.com/view/FMB130_Sleep_modes
Conguration and
rmware update
FOTA Web10, FOTA, Teltonika
Congurator11 (USB, Bluetooth),
FMBT mobile application
(Conguration)
SMS Conguration, Events, DOUT
control, Debug
GPRS commands Conguration, DOUT control, Debug
Time
Synchronization GPS, NITZ, NTP
Fuel monitoring
LLS (Analog), LV-CAN20012, ALL-
CAN30013, OBDII dongle14, CAN-
CONTROL15
Ignition detection
Digital Input 1, Accelerometer,
External Power Voltage, Engine RPM
(CAN Adapters, OBDII dongle)
10 wiki.teltonika-gps.com/view/FOTA_WEB
11 wiki.teltonika-gps.com/view/Teltonika_Congurator
12 teltonika-gps.com/products/trackers/can-obd-data/lv-can200
13 teltonika-gps.com/products/trackers/can-obd-data/lv-can200
14 wiki.teltonika-gps.com/view/How_to_connect_OBD_II_Bluetooth_
Dongle_to_FMB_device
15 wiki.teltonika-gps.com/view/How_to_connect_OBD_II_Bluetooth_
Dongle_to_FMB_device

Quick Manual v1.5 // FMB130 16
ELECTRICAL
CHARACTERISTICS
CHARACTERISTIC
DESCRIPTION VALUE
SUPPLY VOLTAGE MIN. TYP. MAX. UNIT
Supply Voltage
(Recommended
Operating Conditions)
+10 +30 V
DIGITAL OUTPUT (OPEN DRAIN GRADE)
Drain current (Digital
Output OFF) 120 µA
Drain current
(Digital Output ON,
Recommended
Operating Conditions)
0.1 0.5 A
Static Drain-Source
resistance (Digital
Output ON)
400 600 mΩ
DIGITAL INPUT
Input resistance (DIN1) 47 kΩ
Input resistance (DIN2) 38.45 kΩ
Input resistance (DIN3) 150 kΩ
Input voltage
(Recommended
Operating Conditions)
0 Supply
voltage V
Input Voltage threshold
(DIN1) 7.5 V
Input Voltage threshold
(DIN2) 2.5 V
Input Voltage threshold
(DIN3) 2.5 V
ANALOG INPUT
Input voltage
(Recommended
Operating Conditions),
Range 1
0 +10 V
Input resistance,
Range 1 38.45 kΩ
Measurement error on
12V, Range 1 0.9 %
Additional error on 12
V, Range 1 108 mV
Measurement error on
30 V, Range 1 0.33 %
CHARACTERISTIC
DESCRIPTION VALUE
SUPPLY VOLTAGE MIN. TYP. MAX. UNIT

Quick Manual v1.5 // FMB130 17
Additional error on 30
V, Range 1 88 mV
Input Voltage
(Recommended
Operating Conditions),
Range 2
0 +30 V
Input resistance,
Range 2 150 kΩ
Measurement error on
12 V, Range 2 0.9 %
Additional error on 12
V, Range 2 108 mV
Measurement error on
30 V, Range 2 0.33 %
Additional error on 30
V, Range 2 88 mV
OUTPUT SUPPLY VOLTAGE 1-WIRE
Supply voltage +4.5 +4.7 V
Output inner resistance 7 Ω
Output current (Uout
> 3.0 V) 30 mA
Short circuit current
(Uout = 0) 75 mA
CHARACTERISTIC
DESCRIPTION VALUE
SUPPLY VOLTAGE MIN. TYP. MAX. UNIT
NEGATIVE INPUT
Input resistance 38.45 kΩ
Input voltage
(Recommended
Operating Conditions)
0Supply
voltage V
Input voltage threshold 0.5 V
Sink current 180 nA

Quick Manual v1.5 // FMB130 18
This message contains information on how to operate FMB130
safely. By following these requirements and recommendations,
you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating
the device!
• The device uses SELV limited power source. The nominal
voltage is +12 V DC. The allowed voltage range is +10…+30
V DC.
• To avoid mechanical damage, it is advised to transport
the device in an impact-proof package. Before usage,
the device should be placed so that its LED indicators are
visible. They show the status of device operation.
• When connecting the 2x6 connector wires to the vehicle,
the appropriate jumpers of the vehicle power supply
should be disconnected.
• Before unmounting the device from the vehicle, the 2x6
connector must be disconnected. The device is designed
to be mounted in a zone of limited access, which is
inaccessible to the operator. All related devices must meet
the requirements of EN 62368-1 standard.
• The device FMB130 is not designed as a navigational
device for boats.
SAFETY INFORMATION Do not disassemble the device. If the device is
damaged, the power supply cables are not isolated
or the isolation is damaged, DO NOT touch the
device before unplugging the power supply.
All wireless data transferring devices produce
interference that may aect other devices which are
placed nearby.
The programming must be performed using a PC
with autonomic power supply.
The device must be rmly fastened in a predened
location.
The device must be connected only by qualied
personnel.
Installation and/or handling during a lightning storm
is prohibited.
The device is susceptible to water and humidity.
CAUTION: Risk of explosion if battery is replaced
by an incorrect type. Dispose of used batteries
according to the instructions.
Battery should not be disposed of with general
household waste. Bring damaged or worn-out
batteries to your local recycling center or dispose
them to battery recycle bin found in stores.

Quick Manual v1.5 // FMB130 19
CERTIFICATION AND APPROVALS
This sign on the package means that it is necessary
to read the User‘s Manual before your start using the
device. Full User‘s Manual version can be found in
our Wiki1.
1 wiki.teltonika-gps.com/index.php?title=FMB920
Hereby, Teltonika declare under our sole
responsibility that the above described product
is in conformity with the relevant Community
harmonization: European Directive 2014/53/EU
(RED).
This sign on the package means that all used
electronic and electric equipment should not be
mixed with general household waste.
CHECK ALL CERTIFICATES
All newest certicates may be found in our Wiki2.
2 wiki.teltonika-gps.com/view/FMB130_Certication_%26_Approvals
The RoHS1 is a directive regulating the manufacture,
import and distribution of Electronics and Electrical
Equipment (EEE) within the EU, which bans from use
10 dierent hazardous materials (to date).

Quick Manual v1.5 // FMB130 20
WARRANTY
We guarantee our products 24-month warranty1period.
All batteries carry a 6-month warranty period.
Post-warranty repair service for products is not provided.
If a product stops operating within this specic warranty time, the product can be:
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fullling the same functionality
• Replaced with a dierent product fullling the same functionality in case of EOL for the original product
1 Additional agreement for an extended warranty period can be agreed upon separately.
WARRANTY DISCLAIMER
• Customers are only allowed to return products as a result of the product being defective, due to order assembly or
manufacturing fault.
• Products are intended to be used by personnel with training and experience.
• Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance
or inadequate installation – not following operating instructions (including failure to heed warnings) or use with equipment
with which it is not intended to be used.
• Warranty does not apply to any consequential damages.
• Warranty is not applicable for supplementary product equipment (i. e. PSU, power cables, antennas) unless the accessory is
defective on arrival.
• More information on what is RMA1
1 wiki.teltonika-gps.com/view/RMA_guidelines