Teltonika FMB110 Installation guide

Quick Manual
v1.0
Advanced tracker
FMB110

2
FMB110 | Wiki
Table of Contents
Know your device .......................................................................... 3
Pinout................................................................................................. 4
Wiring scheme................................................................................... 5
Set up your device......................................................................... 6
How to insert Micro-SIM card.......................................................... 6
PC Connection (Windows)................................................................ 7
How to install USB drivers (Windows)............................................. 7
Configuration (Windows) ................................................................. 7
Mounting recommendations ....................................................... 9
LED indications ............................................................................ 10
Characteristics............................................................................. 10
Basic characteristics ....................................................................... 10
Electrical characteristics ................................................................. 12
Safety information ...................................................................... 13
Certification and Approvals ....................................................... 14

3
FMB110 | Wiki
Know your device
Figure 1 FMB110 device view

4
FMB110 | Wiki
Pinout
Table 1 FMB110 2x6 socket pinout
Pinnumber Pinname Description
1 VCC (10-30)V DC (+) Power supply (+10-30 V DC).
2 AIN 1 Analog input, channel 1. Input range: 0-
30 V DC.
3 AIN 2 / DIN 3 Analog input, channel 2. Input range: 0-
30 V DC / Digital input, channel 3.
4 DIN 2 Digital input, channel 2.
5 DIN 1 Digital input, channel 1.
6 INPUT 6 TX EXT (LVCAN – TX).
7 GND (-) Digital output, channel 1. Open
collector output. Max. 3,3 A DC.
8 DOUT 1 Digital output, channel 1. Open
collector output. Max. 3,3 A DC..
9 DOUT 2 Digital output, channel 2. Open
collector output. Max. 3,3 A DC.
10 1WIRE POWER +3,8 V output for 1–Wire devices.
11 1WIRE DATA Data for 1–Wire devices.
12 INPUT 5 RX EXT (LVCAN - RX).
Figure 2 FMB110 2x6 socket pinout

5
FMB110 | Wiki
Figure 3 FMB110 Wiring scheme
Wiring scheme
1Automotive relay
1

6
FMB110 | Wiki
Set up your device
How to insert Micro-SIM card
1. Gently remove FMB110 cover using plastic pry tool from both
sides.
2. Insert Micro-SIM card as shown with PIN request disabled or
read our Wiki how to enter it later in Configurator. Make sure
that Micro-SIM card cut-off corner is pointing forward to slot.
3. Attach device cover back.
4. Device is ready to be connected.
Figure 4 Cover removal Figure 5 Micro-SIM card insert Figure 6 Attaching cover back Figure 7 Device is ready

7
FMB110 | Wiki
PC Connection (Windows)
1. Power-up FMB110 with DC voltage (10 – 30 V) power supply
using supplied power cable. LED’s should start blinking, see
“LED indications”.
2. Connect device to computer using Micro-USB cable or Blue-
tooth connection:
•Using Micro-USB cable
▬You will need to install USB drivers, see “How to install
USB drivers (Windows)”
•Using Blue-tooth
▬FMB110 Blue-tooth is enabled by default. Turn on Blue-
tooth on your PC, then select Add Blue-tooth or other
device > Blue-tooth. Choose your device named –
“FMBxxx_last_7_imei_digits”, without LE in the end.
Enter default password 5555, press Connect and then
select Done.
3. You are now ready to use the device on your computer.
How to install USB drivers
(Windows)
1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
setup.
Configuration (Windows)
At first FMB110 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator
software. Contact sales manager to get the latest Configurator
version or download it from here.Configurator operates on
Microsoft Windows OS and uses prerequisite MS .NET
Framework. Make sure you have the correct version installed.
Table 2 MS .NET requirements
MS.NETrequirements
Operating
system
MS .NET Framework
version Version Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2 32 and 64 bit www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can
be changed by clicking in the right bottom corner (Figure 8
Language selection).

8
FMB110 | Wiki
Configuration process begins by pressing on connected device
(Figure 9 Device connected via USB).
After connection to Configurator Status window will be displayed
(Figure 10 Configurator Status window).
Various Status window tabs display information about GNSS,
GSM, I/O, Maintenance and etc. FMB110 has one user editable
profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
functionality:
1. Load from device – loads configuration from device.
2. Save to device – saves configuration to device.
3. Load from file – loads configuration from file.
4. Save to file – saves configuration to file.
5. Update firmware – updates firmware on device.
6. Read records – reads records from the device.
7. Reboot device – restarts device.
8. Reset configuration – sets device configuration to
default.
Most important configurator section is GPRS – where all your
server and GPRS settings can be configured and Data Acquisition
–where data acquiring parameters can be configured.
More details about FMB110 configuration using Configurator can
be found in our Wiki.
Figure 9 Device connected via USB
Figure 8 Language selection
Figure 10 Configurator Status window

9
FMB110 | Wiki
Mounting recommendations
•Connecting wires
▬Wires should be connected while the module is not plugged
in.
▬Wires should be fastened to stable wires or other non-
moving parts. Any heat emitting and/or moving objects
should be kept away from the wires.
▬There should be no exposed wires. If factory isolation was
removed while connecting the wires, the isolation material
should be applied.
▬If the wires are placed in the exterior or in places where they
can be damaged or exposed to heat, humidity, dirt, etc.,
additional isolation should be applied and the wires should
not be loose.
▬Wires cannot be connected to the board computers or
control units.
•Connecting power source
▬Be sure that after the car computer goes to sleep mode,
power might be still available on the power wires.
Depending on the car model, this may happen in 5 to 30
minutes period.
▬When the module is connected, measure the voltage again
to make sure it did not decrease.
▬It is recommended to connect to the main power cable in
the fuse box.
▬3 A, 125 V external fuse shall be used.
•Connecting ignition wire
▬Be sure to check if it is a real ignition wire i. e. power does
not disappear after starting the engine.
▬Check if this is not an ACC wire (when key is in the first
position, most of the vehicle electronics are available).
▬Check if power is still available when you turn off any of
vehicles devices.
▬Ignition is connected to the ignition relay output. As
alternative, any other relay, which has power output when
ignition is on, may be chosen.
•Connecting ground wire
▬Ground wire is connected to the vehicle frame or metal
parts that are fixed to the frame.
▬If the wire is fixed with the bolt, the loop must be connected
to the end of the wire.
▬For better contact scrub paint from the spot where loop is
going to be connected.

10
FMB110 | Wiki
LED indications
Table 3 Navigation LED indications
Behaviour Meaning
Permanently switched on GNSS signal is not received
Blinking every second Normal mode, GNSS is working
Off
GNSS is turned off because:
Device is not working or Device is in
sleep mode
Blinking fast constantly Device firmware is being flashed
Table 4 Status LED indications
Behaviour Meaning
Blinking every second Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
Off Device is not working or Device is in
boot mode
Characteristics
Basic characteristics
Table 5 Basic characteristics
Module
Name TM2500
Technology GSM, GPRS, GNSS, BLUE-TOOTH
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Accuracy < 3 m
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s
Cellular
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support SMS (text/data)

11
FMB110 | Wiki
Power
Input voltage range 10 - 30 V DC with overvoltage
protection
Power consumption
At 12V < 5 mA (Ultra Deep Sleep)
At 12V < 6 mA (Deep Sleep)
At 12V < 7 mA (Online Sleep)
At 12V < 17 mA (GPS Sleep)
At 12V < 35 mA (nominal)
Blue-tooth
Specification 4.0 + LE
Supported peripherals Temperature and Humidity sensor,
Headset, OBDII dongle
Interface
Digital Inputs 3
Digital Outputs 2
Analog Inputs 2
LV-CAN Inputs 1
1-Wire 1
GNSS antenna Internal High Gain
GSM antenna Internal High Gain
USB 2.0 Micro-USB
LED indication 2 status LED lights
SIM Micro-SIM + eSIM
Memory 128MB internal flash memory
Physicalspecification
Dimensions 79 x 43 x 12 mm (L x W x H)
Weight 50 g
Operatingenvironment
Operating temperature -25 °C to +55 °C
Storage temperature -40 °C to +70 °C
Operating humidity 5% to 95% non-condensing
Ingress Protection Rating IP41
Features
Sensors Accelerometer
Scenarios
Green Driving, Over Speeding
detection, Jamming detection, GNSS
Fuel Counter, DOUT Control Via Call,
Excessive Idling detection, Immobilizer,
iButton Read Notification, Unplug
detection, Towing detection, Crash
detection, Auto Geofence, Manual
Geofence, Trip
Sleep modes GPS Sleep, Online Deep Sleep, Deep
Sleep, Ultra Deep Sleep
Configuration and firmware update
FOTA Web, FOTA, FMB Configurator
(USB, Blue-tooth), FMBT mobile
application (Configuration)
SMS Configuration, Events, DOUT control,
Debug
GPRS commands Configuration, DOUT control, Debug
Time Synchronization GPS, NITZ, NTP
Fuel monitoring LLS (Analog), LV-CAN200, ALL-CAN300,
ODBII dongle
Ignition detection Digital Input 1, Accelerometer, External
Power Voltage, Engine RPM

12
FMB110 | Wiki
Electrical characteristics
Table 6 Electrical characteristics
Characteristicdescription Value
Min. Typ. Max. Unit
SupplyVoltage
Supply Voltage (Recommended Operating
Conditions) +10 +30 V
DigitalOutput(Open Drain grade)
Drain current (Digital Output OFF) 120 µA
Drain current (Digital Output ON,
Recommended Operating Conditions) 0.1 0.5 A
Static Drain-Source resistance (Digital Output
ON) 400 600 mΩ
DigitalInput
Input resistance (DIN1) 47 kΩ
Input resistance (DIN2) 47 kΩ
Input voltage (Recommended Operating
Conditions) 0 Supply voltage V
Input Voltage threshold (DIN1) 7.5 V
Input Voltage threshold (DIN2) 2.5 V
Analog Input
Input voltage (Recommended Operating
Conditions), Range 1 0 +10 V
Input resistance, Range 1 150 kΩ
Measurement error on 12V, Range 1 0.9 %
Additional error on 12 V, Range 1 108 mV
Measurement error on 30 V, Range 1 0.33 %
Additional error on 30 V, Range 1 88 mV
Input Voltage (Recommended Operating
Conditions), Range 2 0 +30 V
Input resistance, Range 2 150 kΩ
Measurement error on 12 V, Range 2 0.9 %
Additional error on 12 V, Range 2 108 mV
Measurement error on 30 V, Range 2 0.33 %
Additional error on 30 V, Range 2 88 mV
OutputSupplyVoltage 1-Wire
Supply voltage +4.5 +4.7 V
Output inner resistance 7 Ω
Output current (Uout > 3.0 V) 30 mA
Short circuit current (Uout = 0) 75 mA

13
FMB110 | Wiki
Safety information
This message contains information on how to operate FMB110
safely. By following these requirements and recommendations,
you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the
device!
•The device uses SELV limited power source. The nominal
voltage is +12 V DC. The allowed voltage range is +10..+30 V DC.
•To avoid mechanical damage, it is advised to transport the
device in an impact-proof package. Before usage, the device
should be placed so that its LED indicators are visible. They
show the status of device operation.
•When connecting the 2x6 connector wires to the vehicle, the
appropriate jumpers of the vehicle power supply should be
disconnected.
•Before unmounting the device from the vehicle, the 2x6
connector must be disconnected. The device is designed to be
mounted in a zone of limited access, which is inaccessible to the
operator. All related devices must meet the requirements of EN
60950-1 standard.
The device FMB110 is not designed as a navigational device for
boats.
Do not disassemble the device. If the device is
damaged, the power supply cables are not
isolated or the isolation is damaged, DO NOT
touch the device before unplugging the power
supply.
All wireless data transferring devices produce
interference that may affect other devices which
are placed nearby.
The device must be connected only by qualified
personnel.
The device must be firmly fastened in a
predefined location.
The programming must be performed using a PC
with autonomic power supply.
Installation and/or handling during a lightning
storm is prohibited.
The device is susceptible to water and humidity.

14
FMB110 | Wiki
Certification and Approvals
•FMB110 EAC
•FMB110 REACH
•FMB110 Declaration of IMEI assignment
This sign on the package means that it is
necessary to read the User‘s Manual before
your start using the device. Full User‘s
Manual version can be found in our Wiki.
This sign on the package means that all used
electronic and electric equipment should not
be mixed with general household waste.
Hereby, Teltonika declare under our sole
responsibility that the above described
product is in conformity with the relevant
Community harmonization: European
Directive 2014/53/EU (RED).