Teltonika Telematics FMM150 Installation guide

FMM150
Advanced tracker with CAN data
reading feature
Quick Manual v1.0

Quick Manual v1.0 // FMM150 2
Telematics
CONTENT
Know your device ..................................................................................................................................................................................................3
Pinout......................................................................................................................................................................................................................4
Wiring scheme .......................................................................................................................................................................................................5
Set up your device.................................................................................................................................................................................................6
PC Connection (Windows) ....................................................................................................................................................................................7
How to install USB drivers (Windows) ................................................................................................................................................................7
Conguration (Windows)......................................................................................................................................................................................8
Quick SMS conguration ................................................................................................................................................................................... 10
Mounting recommendations............................................................................................................................................................................ 12
Basic characteristics........................................................................................................................................................................................... 13
LED indications ................................................................................................................................................................................................... 13
Electrical characteristics .................................................................................................................................................................................... 17
Safety information ............................................................................................................................................................................................. 19
Certication and Approvals............................................................................................................................................................................... 20
Warranty .............................................................................................................................................................................................................. 21
Warranty disclaimer .......................................................................................................................................................................................... 21

Quick Manual v1.0 // FMM150 3
Telematics
KNOW YOUR DEVICE
2X6
SOCKET
STATUS
LED
CAN
LED
MICRO SIM
SLOT
BATTERY
SOCKET
NAVIGATE
LED
MICRO
USB
TOP VIEW TOP VIEW (WITHOUT COVER)BOTTOM VIEW (WITHOUT COVER)

Quick Manual v1.0 // FMM150 4
Telematics
Pin number Pin name Description
1VCC (10-30) V
DC (+)
Power supply (+10-30
V DC).
2DIN 3 / AIN 2
Analog input, channel
2. Input range: 0-30
V DC / Digital input,
channel 3.
3DIN2-N / AIN1
Digital input, channel 2
/ Analog input, channel
2. Input range: 0-30 V
DC /GND Sense input
4 DIN1 Digital input, channel
1.
5CAN2L CAN LOW, 2nd line
6CAN1L CAN LOW, 1st line
7 GND (-) Ground pin. (10-30) V
DC (―)
8DOUT 1
Digital output, channel
1. Open collector
output. Max. 0,5 A DC.
9DOUT 2
Digital output, channel
2. Open collector
output. Max. 0,5 A DC.
10 1WIRE DATA Data for 1–Wire
devices.
11 CAN2H CAN HIGH, 2nd line
12 CAN1H CAN HIGH, 1st line
PINOUT
10
9
8
7
11
12
4
3
2
1
5
6
DOUT2
1WIRE DATA
CAN2H
GND
DOUT1
CAN1H
DIN2-N/AIN1
DIN1
CAN2L
DIN3/AIN2
+10...30 V DC
CAN1L
FMM150 2x6 socket pinout

Quick Manual v1.0 // FMM150 5
Telematics
WIRING SCHEME
BUZZER LED LIGHTS
30
8586
87a
87
IGNITION
DETECTION
FUEL GAUGE
RELAY
STARTER
IBUTTON
MULTIPLE
TEMPERATURE
SENSORS
CAN BUS
POWER SUPPLY
10 - 30V DC
ANALOG
LLS SENSOR
ALARM BUTTON
DOOR SENSOR
10
9
8
7
11
12
4
3
2
1
5
6
DOUT2
1WIRE DATA
CAN2H
GND
DOUT1
CAN1H
DIN2-N/AIN1
DIN1
CAN2L
DIN3/AIN2
+10...30 V DC
CAN1L
AIN2
DIN3
DIN2-N
DIN2
1WIRE PWR

Quick Manual v1.0 // FMM150 6
Telematics
SET UP YOUR DEVICE
HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY
4
1COVER REMOVAL 3BATTERY CONNECTION 2MICRO-SIM CARD INSERT ATTACHING COVER BACK
Gently remove FMM150
cover using plastic pry tool
from both sides.
Insert Micro-SIM card as
shown with PIN request
disabled or read our Wiki1
how to enter it later in
Teltonika Congurator2.
Make sure that Micro-
SIM card cut-o corner is
pointing forward to slot.
1 wiki.teltonika-gps.com/index.
php?title=FMB140_Security_info
2 wiki.teltonika-gps.com/view/
Teltonika_Congurator
Connect battery as shown to
device. Position the battery
in place where it does not
obstruct other components.
After conguration, see “PC
Connection (Windows)”,
attach device cover back.

Quick Manual v1.0 // FMM150 7
Telematics
PC CONNECTION (WINDOWS)
HOW TO INSTALL USB DRIVERS (WINDOWS)
1. Please download COM port drivers from here1.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the conrmation window will appear. Click Finish to complete the
setup.
1 teltonika-gps.com/downloads/en/fmm150/TeltonikaCOMDriver.zip
1. Power-up FMM150 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see
“LED indications1”.
2. Connect device to computer using Micro-USB cable or Bluetooth connection:
• Using Micro-USB cable
• You will need to install USB drivers, see “How to install USB drivers (Windows)2”
• Using Bluetooth
• FMM150 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device
> Bluetooth. Choose your device named – “FMM150_last_7_imei_digits”, without LE in the end. Enter default password
5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.
1 wiki.teltonika-gps.com/view/FMM150_LED_status
2 Page 7, "How to install USB drivers"

Quick Manual v1.0 // FMM150 8
Telematics
MS .Net requirements
Operating system MS .NET Framework version Version Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework 4.6.2 32 and 64 bit www.microsoft.com1
1 dotnet.microsoft.com/en-us/download/dotnet-framework/net462
At rst FMM150 device will have default factory settings set. These settings should be changed according to the users needs. Main
conguration can be performed via Teltonika Congurator1software. Get the latest Congurator version from here2. Congurator
operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.
1 wiki.teltonika-gps.com/view/Teltonika_Congurator
2 wiki.teltonika-gps.com/view/Teltonika_Congurator_versions
CONFIGURATION (WINDOWS)

Quick Manual v1.0 // FMM150 9
Telematics
Downloaded Congurator will be in compressed archive.
Extract it and launch Congurator.exe. After launch software
language can be changed by clicking 🌐in the right bottom
corner.
Conguration process begins by pressing on connected device.
FMM150
Various Status window1 tabs display information about GNSS2,
GSM3, I/O4, Maintenance5and etc. FMM150 has one user
editable prole, which can be loaded and saved to the device.
After any modication of conguration the changes need to
be saved to device using Save to device button. Main buttons
oer following functionality:
 Load from device – loads conguration from device.
 Save to device – saves conguration to device.
 Load from le – loads conguration from le.
 Save to le – saves conguration to le.
 Update rmware – updates rmware on device.
 Read records – reads records from the device.
 Reboot device – restarts device.
 Reset conguration – sets device conguration to
default.
Most important congurator section is GPRS – where all
your server and GPRS settings6 can be congured and Data
Acquisition7– where data acquiring parameters can be
congured. More details about FMM150 conguration using
Congurator can be found in our Wiki8.
After connection to Congurator Status window will be
displayed.
FMM150
1 wiki.teltonika-gps.com/view/FMM150_Status_info
2 wiki.teltonika-gps.com/view/FMM150_Status_info#GNSS_Info
3 wiki.teltonika-gps.com/view/FMM1501_Status_info#GSM_Info
4 wiki.teltonika-gps.com/view/FMM150_Status_info#I.2FO_Info
5 wiki.teltonika-gps.com/view/FMM150_Status_info#Maintenance
6 wiki.teltonika-gps.com/index.php?title=FMM150_GPRS_settings
7 wiki.teltonika-gps.com/index.php?title=FMM150_Data_acquisition_settings
8 wiki.teltonika-gps.com/index.php?title=FMM150_Conguration

Quick Manual v1.0 // FMM150 10
Telematics
QUICK SMS CONFIGURATION
Default conguration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:
Note: Before SMS text, two space symbols should be inserted.
GPRS SETTINGS:
 2001 – APN
 2002 – APN username (if there are no APN username,
empty eld should be left)
 2003 – APN password (if there are no APN password,
empty eld should be left)
SERVER SETTINGS:
 2004 – Domain
 2005 – Port
 2006 – Data sending protocol (0 – TCP, 1 – UDP)
« setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0»
1 2 3 4 5 6
1
2
3
4
5
6

Quick Manual v1.0 // FMM150 11
Telematics
DEFAULT CONFIGURATION SETTINGS
MOVEMENT AND IGNITION DETECTION: DEVICE MAKES A RECORD ON MOVING
IF ONE OF THESE EVENTS HAPPEN:
SPEED DIFFERENCE
between last coordinate
and current position is
greater than 10 km/h
VEHICLE DRIVES
100 meters
VEHICLE TURNS
10 degrees
PASSES
300 seconds
After successful SMS conguration, FMM150 device will synchronize time and update records to congured server. Time intervals
and default I/O elements can be changed by using Teltonika Congurator1or SMS parameters2.
1 wiki.teltonika-gps.com/view/Teltonika_Congurator
2 wiki.teltonika-gps.com/view/Template:FMB_Device_Family_Parameter_list
VEHICLE MOVEMENT
will be detected by
accelerometer
DEVICE MAKES A
RECORD ON STOP IF:
1 HOUR PASSES
while vehicle is
stationary and
ignition is o
IGNITION
will be detected by
vehicle power voltage
between 13,2 – 30 V
RECORDS SENDING TO
SERVER:
EVERY 120 SECOND
it is sent to the server
If device has made a
record

Quick Manual v1.0 // FMM150 12
Telematics
MOUNTING RECOMMENDATIONS
CONNECTING WIRES
• Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the
wires.
• The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied
again.
• If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional
isolation should be applied.
• Wires cannot be connected to the board computers or control units.
CONNECTING POWER SOURCE
• Be sure that after the car computer falls asleep, power is still available on chosen wire. Depending on car, this may happen in
5 to 30 minutes period.
• When module is connected, measure voltage again to make sure it did not decrease.
• It is recommended to connect to the main power cable in the fuse box.
• Use 3A, 125V external fuse.
CONNECTING IGNITION WIRE
• Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
• Check if this is not an ACC wire (when key is in the rst position, most of the vehicle electronics are available).
• Check if power is still available when you turn o any of vehicles devices.
• Ignition is connected to the ignition relay output. As alternative, any other relay, which has power output when ignition is on,
may be chosen.
CONNECTING GROUND WIRE
• Ground wire is connected to the vehicle frame or metal parts that are xed to the frame.
• If the wire is xed with the bolt, the loop must be connected to the end of the wire.
• For better contact scrub paint from the spot where loop is going to be connected.

Quick Manual v1.0 // FMM150 13
Telematics
Behaviour Meaning
Permanently
switched on GNSS signal is not received
Blinking every
second Normal mode, GNSS is working
O
GNSS is turned o because:
Device is not working or Device is in
sleep mode
Blinking fast
constantly Device rmware is being ashed
Behaviour Meaning
Blinking every
second Normal mode
Blinking every two
seconds Sleep mode
Blinking fast for a
short time Modem activity
O Device is not working or Device is in
boot mode
Behaviour Meaning
Blinking fast
constantly Reading CAN data from vehicle
Permanently
switched on
Wrong program number or wrong
wire connection
O Wrong connection or CAN
processor in sleep mode
LED INDICATIONS
NAVIGATION LED INDICATIONS
STATUS LED INDICATIONS
CAN STATUS LED INDICATIONS
BASIC CHARACTERISTICS
Module
Name FMM150-Q3IB0: Quectel BG95-M3
with Teltonika TM2500
Technology GSM/GPRS/GNSS/BLUETOOTH
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
QZSS, AGPS
Receiver Tracking: 33
Tracking sensitivity -165 dBM
Accuracy < 3 m
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s

Quick Manual v1.0 // FMM150 14
Telematics
Cellular
Technology LTE Cat M1, GSM
2G bands BG95-M3: B2/B3/B5/B8
4G bands
Cat M1: B1/B2/B3/B4/B5/B8/ B12/
B13/B18/B19/ B20/B25/B26/B27/
B28/B66/B85
Cat NB2: B1/B2/B3/B4/B5/B8/ B12/
B13/B18/B19/ B20/B25/B28/B66/
B71/B85
Data transfer
BG95:
LTE: Max. 588Kbps (DL)/
Max.1119Kbps (UL)
GPRS: Max. 107Kbps (DL)/Max.
85.6Kbps (UL))
Transmit power
Class 4 for GSM850/900: 23±2dBm
Class 1 for GSM1800/1900:
20±2dBm
Class 3 for LTE-TDD: 23±2.7dBm
Class 3 for LTE-FDD: 23±2.7dBm
Power
Input voltage range 10-30 V DC with overvoltage
protection
Back-up battery 170 mAh Li-Ion battery 3.7 V (0.63
Wh)
Internal fuse 3 A, 125 V
Power Consumption
At 12V < 6 mA (Ultra Deep Sleep)
At 12V < 8 mA (Deep Sleep)
At 12V < 11 mA (Online Deep Sleep)
At 12V < 20 mA (GPS Sleep)1
At 12V < 35 mA (nominal with no
load)
At 12V < 250 mA Max. (with full
Load/ Peak)
Bluetooth
Specication 4.0 + LE
Supported
peripherals
Temperature and Humidity
sensor2, Headset3, Inateck Barcode
Scanner, Universal BLE sensors
support
Interface
Digital Inputs 3
Negative Inputs 1 (Digital input 2)
Digital Outputs 2
Analog Inputs 2
CAN interfaces 2
1-Wire 1 (1-Wire data)
1 wiki.teltonika-gps.com/view/FMM150_Sleep_modes#GPS_Sleep_mode
2 teltonika.lt/product/bluetooth-sensor/
3 wiki.teltonika.lt/view/How_to_connect_Blue-tooth_Hands_Free_adapter_
to_FMB_device

Quick Manual v1.0 // FMM150 15
Telematics
GNSS antenna Internal High Gain
GSM antenna Internal High Gain
USB 2.0 Micro-USB
LED indication 3 status LED lights
SIM Micro-SIM + eSIM
Memory 128MB internal ash memory
Physical Specification
Dimensions 65 x 56.6 x 20.6 mm (L x W x H)
Weight 55 g
Operating Environment
Operating
temperature
(without battery)
-40 °C to +85 °C
Storage temperature
(without battery) -40 °C to +85 °C
Operating
temperature (with
battery)
-20 °C to +40 °C
Storage temperature
(with battery)
-20 °C to +45 °C for 1 month
-20 °C to +35 °C for 6 months
Operating humidity 5% to 95% non-condensing
Ingress Protection
Rating IP41
Battery charge
temperature 0 °C to +45 °C
Battery storage
temperature
-20 °C to +45 °C for 1 month
-20 °C to +35 °C for 6 months

Quick Manual v1.0 // FMM150 16
Telematics
Features
CAN Data
Fuel Level (Dashboard), Total
fuel consumption, Vehicle speed
(wheel), Vehicle driven distance,
Engine speed (RPM), Accelerator
pedal position
Sensors Accelerometer
Scenarios
Green Driving, Over Speeding
detection, Jamming detection,
GNSS Fuel Counter, DOUT Control
Via Call, Excessive Idling detection,
Immobilizer, iButton Read
Notication, Unplug detection,
Towing detection, Crash detection,
Auto Geofence, Manual Geofence,
Trip4
Sleep modes GPS Sleep, Online Deep Sleep,
Deep Sleep, Ultra Deep Sleep5
Conguration and
rmware update
FOTA Web6, FOTA7, Teltonika
Congurator8 (USB, Bluetooth),
FMBT mobile application9
(Conguration)
4 wiki.teltonika-gps.com/view/FMM150_Accelerometer_Features_settings
5 wiki.teltonika-gps.com/view/FMM150_Sleep_modes
6 wiki.teltonika.lt/view/FOTA_WEB
7 wiki.teltonika.lt/view/FOTA
8 wiki.teltonika.lt/view/Teltonika_Congurator
9 teltonika.lt/product/fmbt-mobile-application/
SMS Conguration, Events, DOUT
control, Debug
GPRS commands Conguration, DOUT control, Debug
Time
Synchronization GPS, NITZ, NTP
Ignition detection Digital Input 1, Accelerometer,
External Power Voltage, Engine

Quick Manual v1.0 // FMM150 17
Telematics
ELECTRICAL
CHARACTERISTICS
Characteristic description Value
Supply voltage Min. Typ. Max. Unit
Supply Voltage
(Recommended
Operating Conditions)
+10 +30 V
Digital output (open drain grade)
Drain current (Digital
Output OFF) 120 µA
Drain current
(Digital Output ON,
Recommended
Operating Conditions)
0.1 0.5 A
Static Drain-Source
resistance (Digital
Output ON)
400 600 mΩ
Digital input
Input resistance (DIN1) 47 kΩ
Input resistance (DIN2) 38.45 kΩ
Input resistance (DIN3) 150 kΩ
Characteristic description Value
Supply voltage Min. Typ. Max. Unit
Input voltage
(Recommended
Operating Conditions)
0 Supply
voltage V
Input Voltage threshold
(DIN1) 7.5 V
Input Voltage threshold
(DIN2) 2.5 V
Input Voltage threshold
(DIN3) 2.5 V
Output Supply Voltage 1-Wire
Supply voltage +4.5 +4.7 V
Output inner resistance 7 Ω
Output current (Uout
> 3.0 V) 30 mA
Short circuit current
(Uout = 0) 75 mA
Negative input

Quick Manual v1.0 // FMM150 18
Telematics
Input resistance 38.45 kΩ
Input voltage
(Recommended
Operating Conditions)
0Supply
voltage V
Input voltage threshold 0.5 V
Characteristic description Value
Supply voltage Min. Typ. Max. Unit
Sink current 180 nA
CAN Interface
Internal terminal
resistors CAN bus (no
internal termination
resistors)
Ω
Dierential input
resistance 19 30 52 kΩ
Recessive output
voltage 2 2.5 3 V
Dierential receiver
threshold voltage 0.5 0.7 0.9 V
Common mode input
voltage -30 30 V

Quick Manual v1.0 // FMM150 19
Telematics
This message contains information on how to operate
FMM150 safely. By following these requirements and
recommendations, you will avoid dangerous situations. You
must read these instructions carefully and follow them strictly
before operating the device!
• The device uses SELV limited power source. The nominal
voltage is +12 V DC. The allowed voltage range is +10...+30
V DC.
• To avoid mechanical damage, it is advised to transport
the device in an impact-proof package. Before usage,
the device should be placed so that its LED indicators are
visible. They show the status of device operation.
• When connecting the 2x6 connector wires to the vehicle,
the appropriate jumpers of the vehicle power supply
should be disconnected.
• Before unmounting the device from the vehicle, the 2x6
connector must be disconnected. The device is designed
to be mounted in a zone of limited access, which is
inaccessible to the operator. All related devices must meet
the requirements of EN 62368-1 standard. The device
FMM150 is not designed as a navigational device for boats.
SAFETY INFORMATION Do not disassemble the device. If the device is
damaged, the power supply cables are not isolated
or the isolation is damaged, DO NOT touch the
device before unplugging the power supply.
All wireless data transferring devices produce
interference that may aect other devices which are
placed nearby.
The programming must be performed using a PC
with autonomic power supply.
The device must be rmly fastened in a predened
location.
The device must be connected only by qualied
personnel.
Installation and/or handling during a lightning storm
is prohibited.
The device is susceptible to water and humidity.
CAUTION: Risk of explosion if battery is replaced
by an incorrect type. Dispose of used batteries
according to the instructions.
Battery should not be disposed of with general
household waste. Bring damaged or worn-out
batteries to your local recycling center or dispose
them to battery recycle bin found in stores.

Quick Manual v1.0 // FMM150 20
Telematics
CERTIFICATION AND APPROVALS
This sign on the package means that it is necessary
to read the User‘s Manual before your start using the
device. Full User‘s Manual version can be found in
our Wiki1.
1 wiki.teltonika-gps.com/index.php?title=FMM150
This sign on the package means that all used
electronic and electric equipment should not be
mixed with general household waste.
CHECK ALL CERTIFICATES
All newest certicates may be found in our Wiki2.
2 wiki.teltonika-gps.com/view/FMM150_Certication_%26_Approvals