Teltonika TST100 User manual

7. SAFETY INFORMATION
This message contains information on how to operate the device
safely. By following these requirements and recommendations,
you will avoid dangerous situations. Please read these instructions
carefully and follow them strictly before operating the device!
Risk of explosion if battery is replaced by an
incorrect type.
Dispose of used batteries according to the
instructions.
Battery should not be disposed of with general
household waste.
Bring damaged or worn-out batteries to your local
recycling center or dispose them to battery recycle
bin found in stores.
Interference
All wireless data transferring devices produce
interference that may aff ect other devices which are
placed nearby.
The device must be connected only by qualifi ed
personnel.
The device must be fi rmly fastened in a
predefi ned location.
The programming must be performed using a PC
with autonomic power supply.
Do not disassemble the device
If the device is damaged, the power supply cables
are not isolated or the isolation is damaged, DO NOT
touch the device before unplugging the power supply
!
!
Installation and/or handling during a lightning
storm is prohibited.
The device is susceptible to water and humidity if
the device housing is not properly closed.
!
4. CHARACTERISTICS
MODULE
Name Teltonika TM2500
Technology GSM, GPRS, GNSS, BLUETOOTH (4.0 + LE)
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Accuracy < 3 m
GNSS receiver start
times Hot < 1s, Warm < 25s, Cold < 35s
CELLULAR
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support SMS (text)
POWER
Input voltage range 8-50 V DC with overvoltage
protection
Back-up battery 170 mAh Li-ion battery 3.7 V
internal back-up battery
INTERFACE
Modifi cations UART
GNSS antenna Internal High Gain
Cellular antenna Internal High Gain
Sensors Accelerometer
Interface 2.0 Micro-USB, Micro-SIM, 128 MB internal fl ash
memory
LED indication 2 status LED lights
Buzzer Internal
PHYSICAL SPECIFICATION
Dimensions 78 x 75 x 70 (L x W x H)
Weight 130g
Ingress Protection Rating IP67
SOFTWARE
Confi guration and
fi rm-ware update
FOTA WEB (cloud-based solution), Teltonika
Confi gurator (USB, Bluetooth)
Features
Jamming detection, Unplug detection, Fall
Down, Auto Geofence, Manual Geofence, Trip
start and stop detection, Permanent link with
server and many more.
Data reading*
Current speed, Average speed, Total mileage,
Scooter temperature, Built-in battery
temperature, Predicted remaining range,
Battery percentage, Current operation mode,
Error codes, Riding time
Scooter control*
Power on/off the engine, Lock/unlock, Lights
on/off /blink, Siren on/off /beep, Set speed limit
(per mode)
Sleep modes GPS Sleep, Online Deep Sleep
Protocols UDP/TCP/SMS
Data sending Main, Duplicate and Backup servers
Security
Confi guration password, SMS login and
password, Authorized GSM numbers list, Alarm
played through a buzzer
Time
Synchronization GNSS, NTP, NITZ
Supported
peripherals
Temperature and humidity sensor, Universal
BLE sensors support, Solebe BT lock and Segway
wired lock support*
* Depends on scooter model
TST100
KICK E-SCOOTER TRACKEREASY
Quick Start Guide
• TST100 CE / RED
• TST100 EAC
• TST100 Ukrainian UCRF
• TST100 RoHS
• TST100 Declaration of IP rating
• Declaration of IMEI assignment
• Declaration of IMEI security
• REACH Regulation Declaration
TELTONIKA gives guarantee for its products for a period
of 24 months. All batteries carry a reduced 6 month
warranty period. If a product fails within mentioned
warranty period the product can be:
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfi lling
the same functionality
• Replaced by an equivalent product if the production
is discontinued.
How to submit a warranty claim
To obtain warranty service, please register Return
Merchandise Authorization (RMA) query in VIP Helpdesk
or contact your sales manager. After gatheringinformation
support engineer will initiate RMA form, which the user
would need to fi ll in. Once the form is confi rmed, it must
be printed and sent with the shipment.
More information can be found at:
https://teltonika-iot-group.com/warranty-repair/
5. WARRANTY AND RETURN POLICIES
6. CERTIFICATIONS AND APPROVALS

1 2 3
1. Remove the top cover.
2. Insert Micro-SIM card as shown with PIN request disabled. Make sure that Micro-SIM card cut-off corner is
pointing forward to slot.
3. Connect the battery.
4. To power up TST100, connect the plug to the E-scooter.
5. Confi gure the device by connecting micro-USB from TST100 to PC
6. After confi guration, disconnect TST100 from PC. Attach the lid and put the screws back in as shown.
7. Device is ready to be used.
PIN NAME JL-F39-Z508JG CABLE CONNECTOR PIN NO. TST100 PCB PIN NO.
VCC (+) (8-50)V DC 1 1
GND (-) 5 2
RX 3 3
TX 4 4
Power Control Wire (PCW) 2 5
3. After you have fi nished confi guring the device, press Save to device button.
4. When confi guration is saved, disconnect the device from USB and reattach the cover.
1. Power-up the device with DC voltage E-scooter or external (8 – 50 V) power supply using supplied power
cable. LED’s should start blinking, see LED behavior description.
2. Connect device to computer using Micro-USB cable or Bluetooth (Device Bluetooth is enabled by default, default
password 5555) connection.
3. You are now ready to use the device on your computer.
1. Connect device to computer using Micro-USB cable and open Teltonika Confi gurator.
2. Confi guration process begins by pressing on connected device:
1. Please download COM port drivers from Teltonika
here:
https://wiki.teltonika-mobility.com/wikibase/images/d/
d0/TeltonikaCOMDriver.zip
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and
eventually the confi rmation window will appear.
Click Finish to complete the setup.
At fi rst the device will have default factory settings set
unless you order pre-confi gured device. These settings
should be changed according to the user’s needs.
Main confi guration can be performed via Teltonika
Confi gurator software. Confi gurator operates on
Microsoft Windows OS and uses prerequisite MS .NET
Framework. Make sure you have the correct version
installed: MS .NET Framework 4.6.2 or newer.
2.CONFIGURE YOUR DEVICE
3. LED INDICATIONS
2.1. PC PREPARATION (WINDOWS)
1.1. PINOUT
2.2. CONFIGURATOR (WINDOWS)
2.3. DEVICE CONNECTION TO CONFIGURATOR (WINDOWS)
2.4. CONFIGURE THE DEVICE
1. SET UP YOUR DEVICE*
Micro-SIM card insertion/removal must be performed when device is powered off – external
voltage and battery are disconnected. Otherwise, Micro-SIM card might be damaged or device
will not detect it.
!
More details about device confi guration using Teltonika Confi gurator can be found in the Teltonika
TELEMEDIC wiki knowledge base https://wiki.teltonika-mobility.com
Note! Always double check GND and PCW PINS!
4 5 6 7
BEHAVIOR MEANING
Blinking every second Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
O ff Device is not working or Device is in boot mode
Permanently switched on GNSS signal is not received
Blinking every second Normal mode, GNSS is working
O ff GNSS is turned off because Device is not working or Device is in sleep mode
Blinking fast constantly Device fi rmware is being fl ashed
*Given instructions are for sharing version of Segway kick e-scooters with exposed cable on the tube.

1 2 3
1. Remove the top cover.
2. Insert Micro-SIM card as shown with PIN request disabled. Make sure that Micro-SIM card cut-off corner is
pointing forward to slot.
3. Connect the battery.
4. To power up TST100, connect the plug to the E-scooter.
5. Confi gure the device by connecting micro-USB from TST100 to PC
6. After confi guration, disconnect TST100 from PC. Attach the lid and put the screws back in as shown.
7. Device is ready to be used.
PIN NAME JL-F39-Z508JG CABLE CONNECTOR PIN NO. TST100 PCB PIN NO.
VCC (+) (8-50)V DC 1 1
GND (-) 5 2
RX 3 3
TX 4 4
Power Control Wire (PCW) 2 5
3. After you have fi nished confi guring the device, press Save to device button.
4. When confi guration is saved, disconnect the device from USB and reattach the cover.
1. Power-up the device with DC voltage E-scooter or external (8 – 50 V) power supply using supplied power
cable. LED’s should start blinking, see LED behavior description.
2. Connect device to computer using Micro-USB cable or Bluetooth (Device Bluetooth is enabled by default, default
password 5555) connection.
3. You are now ready to use the device on your computer.
1. Connect device to computer using Micro-USB cable and open Teltonika Confi gurator.
2. Confi guration process begins by pressing on connected device:
1. Please download COM port drivers from Teltonika
here:
https://wiki.teltonika-mobility.com/wikibase/images/d/
d0/TeltonikaCOMDriver.zip
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and
eventually the confi rmation window will appear.
Click Finish to complete the setup.
At fi rst the device will have default factory settings set
unless you order pre-confi gured device. These settings
should be changed according to the user’s needs.
Main confi guration can be performed via Teltonika
Confi gurator software. Confi gurator operates on
Microsoft Windows OS and uses prerequisite MS .NET
Framework. Make sure you have the correct version
installed: MS .NET Framework 4.6.2 or newer.
2.CONFIGURE YOUR DEVICE
3. LED INDICATIONS
2.1. PC PREPARATION (WINDOWS)
1.1. PINOUT
2.2. CONFIGURATOR (WINDOWS)
2.3. DEVICE CONNECTION TO CONFIGURATOR (WINDOWS)
2.4. CONFIGURE THE DEVICE
1. SET UP YOUR DEVICE*
Micro-SIM card insertion/removal must be performed when device is powered off – external
voltage and battery are disconnected. Otherwise, Micro-SIM card might be damaged or device
will not detect it.
!
More details about device confi guration using Teltonika Confi gurator can be found in the Teltonika
TELEMEDIC wiki knowledge base https://wiki.teltonika-mobility.com
Note! Always double check GND and PCW PINS!
4 5 6 7
BEHAVIOR MEANING
Blinking every second Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
O ff Device is not working or Device is in boot mode
Permanently switched on GNSS signal is not received
Blinking every second Normal mode, GNSS is working
O ff GNSS is turned off because Device is not working or Device is in sleep mode
Blinking fast constantly Device fi rmware is being fl ashed
*Given instructions are for sharing version of Segway kick e-scooters with exposed cable on the tube.

1 2 3
1. Remove the top cover.
2. Insert Micro-SIM card as shown with PIN request disabled. Make sure that Micro-SIM card cut-off corner is
pointing forward to slot.
3. Connect the battery.
4. To power up TST100, connect the plug to the E-scooter.
5. Confi gure the device by connecting micro-USB from TST100 to PC
6. After confi guration, disconnect TST100 from PC. Attach the lid and put the screws back in as shown.
7. Device is ready to be used.
PIN NAME JL-F39-Z508JG CABLE CONNECTOR PIN NO. TST100 PCB PIN NO.
VCC (+) (8-50)V DC 1 1
GND (-) 5 2
RX 3 3
TX 4 4
Power Control Wire (PCW) 2 5
3. After you have fi nished confi guring the device, press Save to device button.
4. When confi guration is saved, disconnect the device from USB and reattach the cover.
1. Power-up the device with DC voltage E-scooter or external (8 – 50 V) power supply using supplied power
cable. LED’s should start blinking, see LED behavior description.
2. Connect device to computer using Micro-USB cable or Bluetooth (Device Bluetooth is enabled by default, default
password 5555) connection.
3. You are now ready to use the device on your computer.
1. Connect device to computer using Micro-USB cable and open Teltonika Confi gurator.
2. Confi guration process begins by pressing on connected device:
1. Please download COM port drivers from Teltonika
here:
https://wiki.teltonika-mobility.com/wikibase/images/d/
d0/TeltonikaCOMDriver.zip
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and
eventually the confi rmation window will appear.
Click Finish to complete the setup.
At fi rst the device will have default factory settings set
unless you order pre-confi gured device. These settings
should be changed according to the user’s needs.
Main confi guration can be performed via Teltonika
Confi gurator software. Confi gurator operates on
Microsoft Windows OS and uses prerequisite MS .NET
Framework. Make sure you have the correct version
installed: MS .NET Framework 4.6.2 or newer.
2.CONFIGURE YOUR DEVICE
3. LED INDICATIONS
2.1. PC PREPARATION (WINDOWS)
1.1. PINOUT
2.2. CONFIGURATOR (WINDOWS)
2.3. DEVICE CONNECTION TO CONFIGURATOR (WINDOWS)
2.4. CONFIGURE THE DEVICE
1. SET UP YOUR DEVICE*
Micro-SIM card insertion/removal must be performed when device is powered off – external
voltage and battery are disconnected. Otherwise, Micro-SIM card might be damaged or device
will not detect it.
!
More details about device confi guration using Teltonika Confi gurator can be found in the Teltonika
TELEMEDIC wiki knowledge base https://wiki.teltonika-mobility.com
Note! Always double check GND and PCW PINS!
4 5 6 7
BEHAVIOR MEANING
Blinking every second Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
O ff Device is not working or Device is in boot mode
Permanently switched on GNSS signal is not received
Blinking every second Normal mode, GNSS is working
O ff GNSS is turned off because Device is not working or Device is in sleep mode
Blinking fast constantly Device fi rmware is being fl ashed
*Given instructions are for sharing version of Segway kick e-scooters with exposed cable on the tube.

7. SAFETY INFORMATION
This message contains information on how to operate the device
safely. By following these requirements and recommendations,
you will avoid dangerous situations. Please read these instructions
carefully and follow them strictly before operating the device!
Risk of explosion if battery is replaced by an
incorrect type.
Dispose of used batteries according to the
instructions.
Battery should not be disposed of with general
household waste.
Bring damaged or worn-out batteries to your local
recycling center or dispose them to battery recycle
bin found in stores.
Interference
All wireless data transferring devices produce
interference that may aff ect other devices which are
placed nearby.
The device must be connected only by qualifi ed
personnel.
The device must be fi rmly fastened in a
predefi ned location.
The programming must be performed using a PC
with autonomic power supply.
Do not disassemble the device
If the device is damaged, the power supply cables
are not isolated or the isolation is damaged, DO NOT
touch the device before unplugging the power supply
!
!
Installation and/or handling during a lightning
storm is prohibited.
The device is susceptible to water and humidity if
the device housing is not properly closed.
!
4. CHARACTERISTICS
MODULE
Name Teltonika TM2500
Technology GSM, GPRS, GNSS, BLUETOOTH (4.0 + LE)
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Accuracy < 3 m
GNSS receiver start
times Hot < 1s, Warm < 25s, Cold < 35s
CELLULAR
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support SMS (text)
POWER
Input voltage range 8-50 V DC with overvoltage
protection
Back-up battery 170 mAh Li-ion battery 3.7 V
internal back-up battery
INTERFACE
Modifi cations UART
GNSS antenna Internal High Gain
Cellular antenna Internal High Gain
Sensors Accelerometer
Interface 2.0 Micro-USB, Micro-SIM, 128 MB internal fl ash
memory
LED indication 2 status LED lights
Buzzer Internal
PHYSICAL SPECIFICATION
Dimensions 78 x 75 x 70 (L x W x H)
Weight 130g
Ingress Protection Rating IP67
SOFTWARE
Confi guration and
fi rm-ware update
FOTA WEB (cloud-based solution), Teltonika
Confi gurator (USB, Bluetooth)
Features
Jamming detection, Unplug detection, Fall
Down, Auto Geofence, Manual Geofence, Trip
start and stop detection, Permanent link with
server and many more.
Data reading*
Current speed, Average speed, Total mileage,
Scooter temperature, Built-in battery
temperature, Predicted remaining range,
Battery percentage, Current operation mode,
Error codes, Riding time
Scooter control*
Power on/off the engine, Lock/unlock, Lights
on/off /blink, Siren on/off /beep, Set speed limit
(per mode)
Sleep modes GPS Sleep, Online Deep Sleep
Protocols UDP/TCP/SMS
Data sending Main, Duplicate and Backup servers
Security
Confi guration password, SMS login and
password, Authorized GSM numbers list, Alarm
played through a buzzer
Time
Synchronization GNSS, NTP, NITZ
Supported
peripherals
Temperature and humidity sensor, Universal
BLE sensors support, Solebe BT lock and Segway
wired lock support*
* Depends on scooter model
TST100
KICK E-SCOOTER TRACKEREASY
Quick Start Guide
• TST100 CE / RED
• TST100 EAC
• TST100 Ukrainian UCRF
• TST100 RoHS
• TST100 Declaration of IP rating
• Declaration of IMEI assignment
• Declaration of IMEI security
• REACH Regulation Declaration
TELTONIKA gives guarantee for its products for a period
of 24 months. All batteries carry a reduced 6 month
warranty period. If a product fails within mentioned
warranty period the product can be:
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfi lling
the same functionality
• Replaced by an equivalent product if the production
is discontinued.
How to submit a warranty claim
To obtain warranty service, please register Return
Merchandise Authorization (RMA) query in VIP Helpdesk
or contact your sales manager. After gatheringinformation
support engineer will initiate RMA form, which the user
would need to fi ll in. Once the form is confi rmed, it must
be printed and sent with the shipment.
More information can be found at:
https://teltonika-iot-group.com/warranty-repair/
5. WARRANTY AND RETURN POLICIES
6. CERTIFICATIONS AND APPROVALS

7. SAFETY INFORMATION
This message contains information on how to operate the device
safely. By following these requirements and recommendations,
you will avoid dangerous situations. Please read these instructions
carefully and follow them strictly before operating the device!
Risk of explosion if battery is replaced by an
incorrect type.
Dispose of used batteries according to the
instructions.
Battery should not be disposed of with general
household waste.
Bring damaged or worn-out batteries to your local
recycling center or dispose them to battery recycle
bin found in stores.
Interference
All wireless data transferring devices produce
interference that may aff ect other devices which are
placed nearby.
The device must be connected only by qualifi ed
personnel.
The device must be fi rmly fastened in a
predefi ned location.
The programming must be performed using a PC
with autonomic power supply.
Do not disassemble the device
If the device is damaged, the power supply cables
are not isolated or the isolation is damaged, DO NOT
touch the device before unplugging the power supply
!
!
Installation and/or handling during a lightning
storm is prohibited.
The device is susceptible to water and humidity if
the device housing is not properly closed.
!
4. CHARACTERISTICS
MODULE
Name Teltonika TM2500
Technology GSM, GPRS, GNSS, BLUETOOTH (4.0 + LE)
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Accuracy < 3 m
GNSS receiver start
times Hot < 1s, Warm < 25s, Cold < 35s
CELLULAR
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support SMS (text)
POWER
Input voltage range 8-50 V DC with overvoltage
protection
Back-up battery 170 mAh Li-ion battery 3.7 V
internal back-up battery
INTERFACE
Modifi cations UART
GNSS antenna Internal High Gain
Cellular antenna Internal High Gain
Sensors Accelerometer
Interface 2.0 Micro-USB, Micro-SIM, 128 MB internal fl ash
memory
LED indication 2 status LED lights
Buzzer Internal
PHYSICAL SPECIFICATION
Dimensions 78 x 75 x 70 (L x W x H)
Weight 130g
Ingress Protection Rating IP67
SOFTWARE
Confi guration and
fi rm-ware update
FOTA WEB (cloud-based solution), Teltonika
Confi gurator (USB, Bluetooth)
Features
Jamming detection, Unplug detection, Fall
Down, Auto Geofence, Manual Geofence, Trip
start and stop detection, Permanent link with
server and many more.
Data reading*
Current speed, Average speed, Total mileage,
Scooter temperature, Built-in battery
temperature, Predicted remaining range,
Battery percentage, Current operation mode,
Error codes, Riding time
Scooter control*
Power on/off the engine, Lock/unlock, Lights
on/off /blink, Siren on/off /beep, Set speed limit
(per mode)
Sleep modes GPS Sleep, Online Deep Sleep
Protocols UDP/TCP/SMS
Data sending Main, Duplicate and Backup servers
Security
Confi guration password, SMS login and
password, Authorized GSM numbers list, Alarm
played through a buzzer
Time
Synchronization GNSS, NTP, NITZ
Supported
peripherals
Temperature and humidity sensor, Universal
BLE sensors support, Solebe BT lock and Segway
wired lock support*
* Depends on scooter model
TST100
KICK E-SCOOTER TRACKEREASY
Quick Start Guide
• TST100 CE / RED
• TST100 EAC
• TST100 Ukrainian UCRF
• TST100 RoHS
• TST100 Declaration of IP rating
• Declaration of IMEI assignment
• Declaration of IMEI security
• REACH Regulation Declaration
TELTONIKA gives guarantee for its products for a period
of 24 months. All batteries carry a reduced 6 month
warranty period. If a product fails within mentioned
warranty period the product can be:
• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product fulfi lling
the same functionality
• Replaced by an equivalent product if the production
is discontinued.
How to submit a warranty claim
To obtain warranty service, please register Return
Merchandise Authorization (RMA) query in VIP Helpdesk
or contact your sales manager. After gatheringinformation
support engineer will initiate RMA form, which the user
would need to fi ll in. Once the form is confi rmed, it must
be printed and sent with the shipment.
More information can be found at:
https://teltonika-iot-group.com/warranty-repair/
5. WARRANTY AND RETURN POLICIES
6. CERTIFICATIONS AND APPROVALS