Teltonika TMT250 Installation guide

Quick Manual
v1.0
Autonomous personal tracker
TMT250

2
TMT250 | Wiki
Table of Contents
Know your device .......................................................................... 3
Set up your device......................................................................... 4
How to insert Micro-SIM card and connect the battery................ 4
PC Connection (Windows)................................................................ 5
How to install USB drivers (Windows)............................................. 5
Configuration (Windows) ................................................................. 5
LED indication scenarios .............................................................. 7
Basic characteristics ..................................................................... 7
Safety information ........................................................................ 9
Certification and Approvals ....................................................... 10
Warranty ...................................................................................... 11
Warranty Disclaimer....................................................................... 11

3
TMT250 | Wiki
Know your device
Figure 1 TMT250 device view

4
TMT250 | Wiki
Set up your device
How to insert Micro-SIM card and
connect the battery
1. Unscrew 4 screws counterclockwise.
2. Remove the cover.
3. Insert Micro-SIM card as shown with PIN request disabled or
read our Wiki how to enter it later with Teltonika
Configurator. Make sure that Micro-SIM card cut-off corner is
pointing forward to slot.
4. Connect the battery as shown to device.
5. Attach device cover back and screw in all screws.
6. Device is ready to be used.
Figure 2 Attaching cover back Figure 7 Device is ready
Figure 4 Micro-SIM card insert Figure 3 Battery connection
Figure 5 Unscrew screws Figure 6 Cover removal

5
TMT250 | Wiki
PC Connection (Windows)
1. Turn on your device by holding the power button for around 5
seconds.
2. Connect your device to computer using Magnetic USB cable or
Blue-tooth connection:
•Using Magnetic USB cable
▬You will need to install USB drivers, see “How to install
USB drivers (Windows)”
•Using Blue-tooth
▬TMT250 Blue-tooth is enabled by default. Turn on Blue-
tooth on your PC, then select Add Blue-tooth or other
device > Blue-tooth. Choose your device named –
“TMT250_last_7_imei_digits”, without LE in the end.
Enter default password 5555, press Connect and then
select Done.
3. You are now ready to use the device on your computer.
How to install USB drivers
(Windows)
1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
setup.
Configuration (Windows)
At first TMT250 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator
software. Get the latest Configurator version from here.
Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct
version installed.
Table 1 MS .NET requirements
MS.NETrequirements
Operating
system
MS .NET Framework
version Version Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2 32 and 64 bit www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can
be changed by clicking in the right bottom corner (Figure 8
Language selection).

6
TMT250 | Wiki
Configuration process begins by pressing on connected device
(Figure 9 Device connected via USB).
After connection to Configurator Status window will be displayed
(Figure 10 Configurator Status window).
Various Status window tabs display information about GNSS,
GSM,I/O, Maintenance and etc. TMT250 has one user editable
profile, which can be loaded and saved to the device. After any
modification of configuration the changes need to be saved to
device using Save to device button. Main buttons offer following
functionality:
1. Load from device – loads configuration from device.
2. Save to device – saves configuration to device.
3. Load from file – loads configuration from file.
4. Save to file – saves configuration to file.
5. Update firmware – updates firmware on device.
6. Read records – reads records from the device.
7. Reboot device – restarts device.
8. Reset configuration – sets device configuration to
default.
Most important configurator section is GPRS – where all your
server and GPRS settings can be configured and Data Acquisition
–where data acquiring parameters can be configured.
More details about TMT250 configuration using Configurator can
be found in our Wiki.
Figure 9 Device connected via USB
Figure 8 Language selection
Figure 10 Configurator Status window

7
TMT250 | Wiki
LED indication scenarios
Table 2 LED indication scenarios
SCENARIO Meaning
GSM error
SIM is not inserted, device can’t
connect to the operator or GSM signal
is being jammed
No GNSS fix Device doesn’t have valid GNSS fix and
is searching for coordinates
GNSS fix Device has valid GNSS fix
Device off Device is turning off
Device on Device is turning on
Alarm key pressed Alarm button is pressed and held
Power key pressed Power key is pressed and held
Charging Device is charging
Charging error Overcurrent, low temperature or high
temperature
Fully charged Device is fully charged
Battery low Battery is almost fully discharged
I am alive Indication used to remind the user
that device is still operational
Note! This table contains only the default scenarios. Additional
scenarios/default ones can be modified using Teltonika
Configurator. User is able to select different indication color (Red,
Green or Blue), frequency of LED blinking and vibration status.
Basic characteristics
Table 3 Basic characteristics
Module
Name
TM2500
Technology
GSM, GPRS, GNSS, BLUE-TOOTH
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU,
SBAS, QZSS, DGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Accuracy < 3 m
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s
Cellular
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900
MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240
kbps), GPRS Mobile Station Class B
Data support SMS (text/data)
Power
Charging voltage 5V DC
Battery 800 mAh Li-Ion battery (3,04 Wh)
Power consumption
1,5 mA (Ultra Deep Sleep)
3,5 mA (Deep Sleep)
4 mA (Online Deep Sleep)
8 mA (GPS Sleep)
44 mA (nominal)

8
TMT250 | Wiki
Blue-tooth
Specification 4.0 + LE
Supported peripherals Temperature and Humidity sensor,
Headset
Interface
Configurable buttons 2
GNSS antenna Internal High Gain
GSM antenna Internal High Gain
USB 2.0 Magnetic USB contact
LED indication 1 RGB LED
SIM Micro-SIM
Memory 128MB internal flash memory
Physicalspecification
Dimensions 44 x 43 x 20 mm (L x W x H)
Weight 40 g
Operatingenvironment
Operating temperature -25 °C to +55 °C
Storage temperature -40 °C to +70 °C
Charging temperature 0 °C to +45 °C
Operating humidity 5% to 95% non-condensing
Ingress Protection Rating IP67
Features
Sensors Accelerometer, Gyroscope
Scenarios
Overspeeding, Man-down, Alarm, Auto
Geofence, Manual Geofence, Action on
call, Movement Event
Sleep modes GPS Sleep, Online Deep Sleep, Deep
Sleep, Ultra Deep Sleep
Configuration and firmware update
FOTA Web, FOTA, FMB Configurator
(USB, Blue-tooth), FMBT mobile
application (Configuration)
SMS Configuration, Events, Debug
GPRS commands Configuration, Debug
Time Synchronization GPS, NITZ, NTP

9
TMT250 | Wiki
Safety information
This message contains information on how to operate TMT250
safely. By following these requirements and recommendations,
you will avoid dangerous situations. You must read these
instructions carefully and follow them strictly before operating the
device!
Use only original batteries. Using uncertified
manufacturer or different type batteries may
cause an explosion.
Use batteries safely. Protect batteries from
moisture, place them in a cool and dry place when
storing. Avoid extensive o
peration at high
temperatures. Do not attempt charging battery
directly from the electrical mains. All utilized
batteries shall comply with IEC 62133.
Power supply circuits used to charge the device
connection must have safeguards, which prevent
power
leakage, short circuits or incorrect
electrical grounding. Any used switches ought to
be installed in a readily accessible location. Power
must be uninterrupted.
Remove device safely. Device must be
disconnected from computer or charger by
unplugging th
e magnetic USB cable from the
device.
In order to prevent device from mechanical
damage it is advisable to transport it in a shock-
resistant packaging. If device stopped working
properly regardless of the settings only a
qualified specialist can help.
Operate the device in suitable conditions. Do not
use the device where mobile connectivity is
forbidden.
Road safety first. Comply with local traffic laws,
always hold you hands on a steering wheel when
using a device. Your safety is of utmost
importance when you drive.
All wireless devices are sensitive to
electromagnetic interference, as a result wireless
devices affect the performance of each other.
Charging precautions. SELV LPS chargers, personal
computers or laptops that device will be
connected to must comply with the requirements
of IEC 60950:2005 standard.

10
TMT250 | Wiki
Certification and Approvals
•TMT250 IP Rating
•TMT250 CE RED
•TMT250 REACH
•TMT250 Declaration of IMEI assignment
This sign on the package means that it is
necessary to read the User‘s Manual before
your start using the device. Full User‘s
Manual version can be found in our Wiki.
This sign on the package means that all used
electronic and electric equipment should not
be mixed with general household waste.
Hereby, Teltonika declare under our sole
responsibility that the above described
product is in conformity with the relevant
Community harmonization: European
Directive 2014/53/EU (RED).