Teltonika TSM232 Installation guide
Quick Manual
v1.1
Iridium Satellite terminal with a
backup battery
TSM232
2
TSM232 | Wiki
Table of Contents
Table of Contents .......................................................................... 2
Know your device .......................................................................... 3
Pinout................................................................................................. 4
Wiring scheme................................................................................... 5
Set up your device......................................................................... 6
How to connect the battery ............................................................. 6
PC Connection (Windows)................................................................ 7
How to install USB drivers (Windows)............................................. 7
Configuration (Windows) ................................................................. 7
Mounting recommendations........................................................... 9
Characteristics............................................................................. 10
Basic characteristics ....................................................................... 10
Electrical characteristics................................................................. 11
Safety information...................................................................... 12
Certification and Approvals ....................................................... 13
Warranty ...................................................................................... 14
Warranty Disclaimer........................................................................14
4
TSM232 | Wiki
Pinout
Table 1 TSM232 6 socket pinout
PIN NUMBER
PIN NAME
DESCRIPTION
1
DOUT1
Digital output, channel 1. Open
collector output. Max. 0,5 A DC
2
RS232-RX
Input for data reception through
RS-232
3
GND
( - ) Ground pin. (10…30) V DC*
4
AIN1
Analog input, channel 1. Input
range: 0-30V/0-10V DC
5
DIN1
Digital input, channel 1
6
RESERVED
7
RS232 –TX
Output for data transmission
through RS-232
8
VCC (6-30) V DC (+)
Power supply (+10-30 V DC).
Figure 2 TSM232 socket pinout
6
TSM232 | Wiki
Set up your device
How to connect the battery
1. Gently remove TSM232 cover using plastic pry tool from both
sides.
2. Connect battery as shown to device. Position the battery in
place where it does not obstruct other components.
3. When battery connected, attach device cover back.
4. Connect External Iridium antenna.
Figure 6 Cover removal
Figure 7 Battery connection
Figure 5 Attaching cover back
Figure 4 Connecting Iridium antenna
7
TSM232 | Wiki
Introduction
TSM232 works as external accessory and no need to configure it.
Following information describes, how to configure main device,
which TSM232 can be connected to.
PC Connection (Windows)
1. Power-up FMB640 device with DC voltage (10 –30 V) power
supply using power wires. LED’s should start blinking.
2. Connect FM device to computer via USB connection:
•Using Micro-USB cable
▬You will need to install USB drivers, see “How to install
USB drivers (Windows)”
3. You are now ready to use the device on your computer.
How to install USB drivers
(Windows)
1. Please download COM port drivers from here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
Setup will continue installing the driver and eventually the
confirmation window will appear. Click Finish to complete the
setup.
Configuration (Windows)
At first FMB640 device will have default factory settings set. These
settings should be changed according to the user's needs. Main
configuration can be performed via Teltonika Configurator
software. Get the latest Configurator version from here.
Configurator operates on Microsoft Windows OS and uses
prerequisite MS .NET Framework. Make sure you have the correct
version installed
.Table 2 MS .NET requirements
MS .NET REQUIREMENTS
Operating
system
MS .NET Framework
version
Version
Links
Windows Vista
Windows 7
Windows 8.1
Windows 10
MS .NET Framework
4.6.2
32 and 64 bit
www.microsoft.com
Downloaded Configurator will be in compressed archive. Extract it
and launch Configurator.exe. After launch software language can
be changed by clicking in the right bottom corner (Figure 8
Language selection).
Figure 8 Language selection
8
TSM232 | Wiki
Configuration process begins by pressing on connected device
(Figure 9 Device connected via USB).
After connection to Configurator Status window will be displayed
(Figure 10 Configurator Status window).
Iridium device can send short burst data (SBD) to server. This
means that some data can be sent from FM device to server
through satellites. In order to get those records, you have to
connect the device to FM6 COM1 or COM2 port. Select COM1 or
COM2 mode Satellite backup mode. Those settings can be found in
RS232/RS485 TAB in the configurator. Baud rate for satellite
devices is 19200 bps. (Figure 11 COM Settings)
Furthermore, TSM232 functionality should be enabled. These
settings can be found in the Features TAB in Short burst data
settings. (Figure 12 SBD Settings)
More details about TSM232 configuration using Configurator can
be found in our Wiki.
Figure 9 Device connected via USB
Figure 10 Configurator Status window
Figure 11 COM Settings
Figure 12 SBD Settings
9
TSM232 | Wiki
Mounting recommendations
•Connecting wires
▬Wires should be connected while the module is not plugged
in.
▬Wires should be fastened to stable wires or other non-
moving parts. Any heat emitting and/or moving objects
should be kept away from the wires.
▬There should be no exposed wires. If factory isolation was
removed while connecting the wires, the isolation material
should be applied.
▬If the wires are placed in the exterior or in places where they
can be damaged or exposed to heat, humidity, dirt, etc.,
additional isolation should be applied and the wires should
not be loose.
▬Wires cannot be connected to the board computers or
control units.
•Connecting power source
▬Be sure that after the car computer goes to sleep mode,
power might be still available on the power wires.
Depending on the car model, this may happen in 5 to 30
minutes period.
▬When the module is connected, measure the voltage again
to make sure it did not decrease.
▬It is recommended to connect to the main power cable in
the fuse box.
▬3 A, 125 V external fuse shall be used.
•Connecting ignition wire
▬Be sure to check if it is a real ignition wire i. e. power does
not disappear after starting the engine.
▬Check if this is not an ACC wire (when key is in the first
position, most of the vehicle electronics are available).
▬Check if power is still available when you turn off any of
vehicles devices.
▬Ignition is connected to the ignition relay output. As
alternative, any other relay, which has power output when
ignition is on, may be chosen.
•Connecting ground wire
▬Ground wire is connected to the vehicle frame or metal
parts that are fixed to the frame.
▬If the wire is fixed with the bolt, the loop must be connected
to the end of the wire.
▬For better contact scrub paint from the spot where loop is
going to be connected.
10
TSM232 | Wiki
Characteristics
Basic characteristics
Table 3 Basic characteristics
MODULE
Name
Iridium 9603 SBD Transceiver
Technology
Iridium satellite transceiver
POWER
Input voltage range
10-30 V DC with overvoltage protection
Back-up battery
Internal Ni-MH backup rechargeable battery 7.2 -
7.5 V 400mAh
Internal fuse
3 A, 125 V
Power consumption
At 12V < 7.13 mA (nominal with no load)
At 12V < 1.0 A Max. (with full Load/Peak)
INTERFACE
Digital Inputs
1
Digital Outputs
1
Analog Inputs
1
RS232
1
Integrated buzzer
1
Antenna
External Iridium antenna
LED indication
2 status LED lights
PHYSICAL SPECIFICATION
Dimensions
64 x 56 x 30 mm (L x W x H)
Weight
210 g
OPERATING ENVIRONMENT
Operating temperature
(without battery)
-25 °C to +55 °C
Storage temperature (without
battery)
-40 °C to +70 °C
Operating humidity
5% to 95% non-condensing
Ingress Protection Rating
IP41
Battery charge temperature
Ambient Temperature 20±5℃
Battery discharge temperature
Ambient Temperature 20±5℃
Battery storage temperature
-20°C to +45°C
FEATURES
Functionalities
Data transferring via Iridium satellite network when
GSM network is unavailable
Smart RS232 communication algorithm
One FMB640/FM63XY message size forwarded to
TSM232 is only 14 bytes
Message contains: Time/Coordinates/Speed/DIN1-
4/DOUT1-2/Event ID
Data sending can be initiated by periodic time
interval or by panic priority event
11
TSM232 | Wiki
Electrical characteristics
Table 4 Electrical characteristics
CHARACTERISTIC DESCRIPTION
VALUE
MIN.
TYP.
MAX.
UNIT
SUPPLY VOLTAGE
Supply Voltage (Recommended Operating
Conditions)
+10
+30
V
DIGITAL OUTPUT (OPEN DRAIN GRADE)
Drain current (Digital Output OFF)
120
µA
Drain current (Digital Output ON,
Recommended Operating Conditions)
0.5
A
Static Drain-Source resistance (Digital Output
ON)
120
mΩ
DIGITAL INPUT
Input resistance (DIN 1)
59.9
kΩ
Input voltage (Recommended Operating
Conditions)
0
60
V
Input Voltage threshold (DIN 1)
7.5
7.7
8
V
ANALOG INPUT
Input voltage (Recommended Operating
Conditions), Range 1
0
+10
V
Input resistance, Range 1
120
kΩ
12
TSM232 | Wiki
Safety information
This message contains information on how to operate TSM232 safely. By
following these requirements and recommendations, you will avoid
dangerous situations. You must read these instructions carefully and
follow them strictly before operating the device!
•The device uses SELV limited power source. The nominal voltage is
+12 V DC. The allowed voltage range is +10…+30 V DC.
•To avoid mechanical damage, it is advised to transport the device in
an impact-proof package. Before usage, the device should be placed
so that its LED indicators are visible. They show the status of device
operation.
•When connecting the 8 connectors wires to the vehicle, the
appropriate jumpers of the vehicle power supply should be
disconnected.
•Before unmounting the device from the vehicle, the 8 connectors
must be disconnected. The device is designed to be mounted in a
zone of limited access, which is inaccessible to the operator. All
related devices must meet the requirements of EN 62368-1 standard.
The device TSM232 is not designed as a navigational device for boats.
Do not disassemble the device. If the device is
damaged, the power supply cables are not
isolated or the isolation is damaged, DO NOT
touch the device before unplugging the power
supply.
All wireless data transferring devices produce
interference that may affect other devices which
are placed nearby.
The device must be connected only by qualified
personnel.
The device must be firmly fastened in a
predefined location.
The programming must be performed using a PC
with autonomic power supply.
Installation and/or handling during a lightning
storm is prohibited.
The device is susceptible to water and humidity.
Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries
according to the instructions.
Battery should not be disposed of with general
household waste. Bring damaged or worn-out
batteries to your local recycling center or dispose
them to battery recycle bin found in stores.
13
TSM232 | Wiki
Certification and Approvals
•TSM232 REACH
•TSM232 CE/RED
This sign on the package means that it is
necessary to read the User‘s Manual before
your start using the device. Full User‘s
Manual version can be found in our Wiki.
This sign on the package means that all used
electronic and electric equipment should not
be mixed with general household waste.
Hereby, Teltonika declare under our sole
responsibility that the above described
product is in conformity with the relevant
Community harmonization: European
Directive 2014/53/EU (RED).
14
TSM232 | Wiki
Warranty
TELTONIKA guarantees its products to be free of any
manufacturing defects for a period of 24 months. With additional
agreement we can agree on a different warranty period, for more
detailed information please contact our sales manager.
Contact us teltonika.lt/company/contacts
If a product should fail within this specific warranty time, the
product can be:
•Repaired
•Replaced with a new product
•Replaced with an equivalent repaired product fulfilling the
same functionality
•TELTONIKA can also repair products that are out of warranty
at an agreed cost.
Warranty Disclaimer
TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS
WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS
THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL
IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY
EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY
ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE,
LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC
LOSS.
More information can be found at teltonika.lt/warranty-repair
Table of contents
