Teltonika RUT723 User manual

WiMAX Outdoor Router
User Manual
Version 1.04
Applies to:
RUT723, RUT725, RUT735 and RUT738
Suitable for RUT7xx

LEGAL NOTICE
Copyright © 2012 TELTONIKA Ltd. All rights reserved. Reproduction, transfer, distribution or
storage of part or all of the contents in this document in any form without the prior written
permission of TELTONIKA Ltd is prohibited. The manufacturer reserves the right to modify the
product and manual for the purpose of technical improvement without prior notice.
Other product and company names mentioned herein may be trademarks or trade names of their
respective owners.
ATTENTION
Before using the device we strongly recommend reading this
user manual first.
Do not rip open the device. Do not touch the device if the
device block is broken.
Device should be serviced only by qualified personel.
All wireless devices for data transferring may be susceptible to
interference, which could affect performance.
The device is water-resistant (IP65) and can be mounted
outdoor, though power adapter must be kept dry.

Table of contents
LEGAL NOTICE............................................................................................................................................................. 2
ATTENTION ................................................................................................................................................................. 2
TABLE OF CONTENTS................................................................................................................................................... 3
SAFETY INFORMATION................................................................................................................................................ 4
DEVICE SERVICE .......................................................................................................................................................... 5
PRODUCT OVERVIEW.................................................................................................................................................. 6
INTRODUCTION................................................................................................................................................................... 6
PACKAGE CONTENTS ............................................................................................................................................................ 6
SYSTEM REQUIREMENTS ....................................................................................................................................................... 6
HARDWARE INSTALLATION ......................................................................................................................................... 7
CONNECTING DEVICE ........................................................................................................................................................... 7
MOUNTING DEVICE ............................................................................................................................................................. 8
WEB GUI OVERVIEW................................................................................................................................................... 9
CONNECTING TO THE WEBUI ................................................................................................................................................ 9
WEBUI STRUCTURE........................................................................................................................................................... 10
STATUS............................................................................................................................................................................ 10
ETHERNET ....................................................................................................................................................................... 11
IP address ................................................................................................................................................................ 11
DHCP server............................................................................................................................................................. 11
FIREWALL ........................................................................................................................................................................ 12
Port forwarding ....................................................................................................................................................... 12
Mac filtering ............................................................................................................................................................ 13
IP filtering ................................................................................................................................................................ 14
Demilitarization zone .............................................................................................................................................. 15
ADMINISTRATION.............................................................................................................................................................. 15
Settings.................................................................................................................................................................... 15
Firmware ................................................................................................................................................................. 16
Password ................................................................................................................................................................. 16
ABOUT............................................................................................................................................................................ 16
TROUBLESHOOTER: ...................................................................................................................................................17
TECHNICAL SPECIFICATIONS:......................................................................................................................................19
ELECTRICAL,MECHANICAL &ENVIRONMENTAL:...................................................................................................................... 19

4
SAFETY INFORMATION
In this section you will be introduced on how to use a WiMAX Outdoor Router safely. You have
to be familiar with the safety requirements before using the device! We suggest you to adhere to
the following recommendations in order to avoid personal injuries and or property damage.
The device is intended for supply from a Limited Power Source
(LPS) that power consumption should not exceed 15VA and
current rating of overcurrent protective device should not
exceed 2A.
The highest transient overvoltage in the output (secondary
circuit) of used PSU shall not exceed 71V peak.
The device can be used with the Personal Computer (first safety
class) or Notebook (second safety class). Associated
equipment: PSU (power supply unit) (LPS) and personal
computer (PC) shall comply with the requirements of standard
EN 60950-1.
Do not mount or serve device during a thunderstorm.
Device is mounted in limited access areas.
To avoid mechanical damages to the device it is recommended
to transport it packed in a damage-proof pack.
Protection in primary circuits of associated PC and PSU (LPS)
against short circuits and earth faults of associated PC shall
be provided as part of the building installation.

5
This automatic two pole protective device disconnects all the associated equipment (fig 1).
To disconnect the device plug off the AC-DC power adapter from the wall outlet or power strip.
The gap between contacts should be no less than 3mm.
1 Figure: Building installation scheme
Device service
Signal level of the device depends on the working environment. In case the device starts working
insufficiently, please refer to qualified personnel in order to repair this product.
There are no exchangeable parts within the device including 2A quick acting fuse.
Device should be serviced only by qualified personel. Opening the device will void the warranty for
this product. We recommend forward it to a repair center or to the manufacturer.
Labels with product information (serial number and MAC address) can be found on the bottom
side of the device as well as on the packaging.

6
PRODUCT OVERVIEW
Introduction
Teltonika RUT723, RUT725, RUT735 and RUT738 are outdoor routers offering high speed data rate
connectivity to the WiMAX networks. Router is compliant with IEEE802.16e-2005 WiMAX Wave 2.
10/100 Base-T interface and integrated DHCP server allow easy connection to any device with
Ethernet cable. Teltonika outdoor WiMAX router is ideal for distant locations. High gain MIMO
antenna improves coverage and pole mounting kit ensures stable signal conditions. Included POE
adapter allows the device to function with only Ethernet cable connected.
Package contents
WiMAX Outdoor Router
WiMAX Outdoor Router
Pole mounting kit
POE Adapter
2 x LAN cable
Waterproof RJ45 connector kit
Quick Start Guide
Note: The provisioning information is provided by your service provider, therefore any questions
regarding connectivity problems should be addressed to it.
Note: If any of the components are missing or damaged, please contact the retailer or reseller
from which this product was purchased.
Note: Using a not IEEE 802.3af-2003 compliant POE adapter with the WiMAX Outdoor Router will
cause damage and void the warranty for this product.
System requirements
Wired network connection.
Windows XP, Windows Vista, Windows 7, MAC OS X, or a Linux-based operating system.
A web browser must have a flash player plug-in (version 10 or higher) in order to access the
Web GUI for network configuration.

7
Hardware installation
Connecting device
Device has included waterproof RJ45 connector. Use it together with LAN cable and assemble as is
shown in the picture below. To connect LAN cable to the router:
1. Plug cable into RJ45 socket
2. Tighten the screw around RJ45 socket
3. Tighten the nut around LAN cable
Device is powered from included POE adapter. Use LAN cables and connect Outdoor WiMAX
Router to POE adapter’s “Data & Power Out” port. Connect “Data In” port to your computer or
switch. Plug POE adapter into AC socket to power the device on. Green light on the bottom left
corner of the Outdoor Router (just above RJ45 socket) indicates that device is powered.

8
Mounting device
Device pole mounting kit contains these elements:
STEP 1
STEP 2
STEP 3
Fix “L” bracket to the router
Assemble pole bracket clamp and
“U” bolt on a pole
Adjust right direction and
tighted the nuts.
Device position and angle of antenna has big impact on performance. By monitoring Status
window in WebUI try to find a location with best signal quality.

9
Web GUI OVERVIEW
In this section you will be briefly introduced to our user interface.
Note: we use an intuitive tool tip system in our web user interface which displays additional data
for the user. To see this data hover your mouse cursor above the field. Also, if the frame of the field
becomes red, it usually means that the data in the field is incorrect, in this case look into red tool
tip for more information.
Connecting to the WebUI
To connect to the configuration web page do the following steps:
1. Type 192.168.0.1 to your favorite internet browser. Skip the step 2 if the password is
disabled.
2. Window asking for authentication will pop up. Enter your username and password (default:
username: user, password: user) and press enter.
3. Status window will appear in a few seconds:
First page of WebUI

10
WebUI structure
Our modern web user interface provides you with all the tools needed within the five main pages:
Status, Ethernet, Firewall, Administration, About.
Status
Status page
The status page consists of 6 properties that define the current state of the WiMAX Outdoor
Router:
1. Uptime –amount of time since the last reboot (or plug in).
2. Signal quality –the quality of a signal in percents (and decibels).
<30% poor
>30% <50% decent
>50% <90% good
>90% very good
Note: signal quality depends on the distance between the device and the base
station, plus other factors: interference with other devices, etc.
3. Signal strength –the strength of the signal in dBm.
4. External IP –IP which was assigned by the base station to your device.
5. MAC address –physical address of the WiMAX connection module.
6. BS MAC address - physical address of the base station.

11
Ethernet
Ethernet settings page allows the user to change the IP address, net mask and DHCP server
settings.
IP address
IP address settings page
IP address –IP address of the router.
Netmask–mask used to divide IP address into subnets.
DHCP server
Dynamic Host Configuration Protocol (DHCP) is a network protocol that enables a server to
automatically assign an IP address to a computer from a defined range of numbers configured for a
given network.
DHCP server form
Enable –check to enable the DHCP server.
First IP address –First IP from the range to be leased.
No. of users –number of IP addresses to be leased.
Lease time –time after the leased IP expires.

12
Firewall
Firewall page lets you configure firewall settings to meet your requirements. It includes port-
forwarding, MAC filtering and IP filtering
Port forwarding
Port forwarding is the process of translating the address and port number of a packet to a new
destination.
Follow these steps to add a port-forwarding rule:
1. Enable –check to enable the Port forwarding.
2. Press the +button.
Port forwarding form
The following port-forwarding rule creation window will pop-up. Choose a rule type (single
port or port range) and fill the fields in a window to define your rule:
Predefined rule –select from a list of most common rules.
Name –the name of the rule that will be visible in the list of your defined rules.
External port from/to –external port range to be redirected to an identical internal
port range.
External port –external port to be redirected to Internal port.
Internal port –port used by the destination device to receive data.
Protocol –protocol in which rule operates.
Destination IP –the address of the device to which all the data coming to the selected
external ports is forwarded to.
New port-forwarding rule windows
3. Press OK button to accept the rule.
4. Press Apply to save the rules to the configuration.

13
Mac filtering
MAC filtering is a security access control method used to determine access to the network by
physical address.
Follow these steps to add a MAC filtering rule:
1. Enable –check to enable the MAC filtering.
2. Press the +button.
Mac filtering form
3. The following MAC filtering rule creation window will pop-up.
New MAC filtering rule window
Name –MAC filtering rule name.
MAC address –physical address that you want to block from connecting to
and/or through the router.
4. Press OK to add the rule.
5. After adding all the rules that you needed, press Apply to save the rules to the
configuration.

14
IP filtering
IP filtering is a security access control method used to determine access to the network by IP
address.
Follow these steps to add an IP filtering rule:
1. Enable –check to enable the IP filtering.
2. Press the +button.
IP filtering form
3. The following IP filtering rule creation window will pop-up.
New IP filtering rule window
Name –IP filtering rule name.
IP address –IP address that you want to block from connecting to and/or
through the router.
4. Press OK to add the rule.
5. After adding all the rules that you needed, press Apply to save the rules to the
configuration.

15
Demilitarization zone
In computer networks, a DMZ (demilitarized zone) is a computer host or small network inserted as
a "neutral zone" between a private network and the outside public network.
DMZ page
To set up DMZ, click the Enablecheckbox and put in IP address of your destination in the
Destination IP text field.
Administration
Administration page allows you to change the language of the WebUI, disable radio connection,
reboot the router, save firmware to your computer (in a binary file format) or update it with the
newer version. In addition, you can set up a new password for WebUI connection.
Settings
Settings page
Language –select a language from the drop down list.
Radio state –disables or enables radio (WiMAX) connection.
Reboot button –click to reboot this device. You will have to wait for a few seconds until it boots up
again.

16
Firmware
Firmware page
To save firmware: click Save firmware to file and at the following dialog browse to the directory
you want to place binary file.
To update firmware:click Select firmware file and at the following dialog window select firmware
file (note: file must be named firmware.bin). To start updating click: Update firmware. This
process usually takes 5 to 10 minutes.
Note:A firmware backup is only suitable for the device from which it was downloaded. If a
firmware backup is uploaded to another router, that device will malfunction.
Password
To set up or change a password check Enable user password and write a new one into two fields
bellow. To disable user password simply uncheck Enable user password checkbox. You must click
Apply if you want to save any of these to configuration.
Note: it is strongly not recommended to disable user password if a router is reachable from Local
area network
About
About page
The About page displays the versions of your firmware and software that are currently running on
your device. This helps you decide whether or not you need to update your firmware.
Note: The last part in the OS version string refers to the sector size (64 kilobytes in this case) of the
flash memory. It is important that the firmware you update is made for the same flash sector size
as the flash memory in the device.

17
Troubleshooter:
Q: I think my router is not working: can not acquire connection and WebUI is not reachable.
A: Check if IP address is set to obtain automatically via DHCP. Follow these steps:
Windows 7:
Go to Control panel ->Network and internet -> Network sharing center -> change adapter
settings.
Right click on a Local Area Connection which uses WiMAX Outdoor Router for connecting to
the internet and click Properties.
Check Internet Protocol IPv4 (TCP/IP) and click Properties.

18
Make sure that Obtain IP address automatically is checked in the General settings.
Click OK.

19
Technical Specifications:
Standard Compliant IEEE 802.16e-2005
Air Interface S-OFDMA
Frequency Band 3.3 –3.6 GHz (RUT735) or 2.5 –2.7 GHz (RUT725)
Channel Bandwidth 3 MHz, 3.5 MHz, 5 MHz, 6 MHz, 7 MHz, 8.75 MHz and 10 MHz
Modulation Adaptive QPSK, 16QAM, 64QAM
MIMO MRC, Matrix A + MRC, Matrix B
Beamforming All I/O Beamforming Items
RF Output Power 2 x 23 dBm @ 3.3-3.6 GHz (RUT735) or
2 x 25 dBm @ 2.5-2.7GHz (RUT725)
RX Sensitivity QPSK1/2: -99 @ 3.5 GHz and 10 MHz BW
16QAM1/2: -93.8 @ 3.5 GHz and 10 MHz BW (RUT735)
QPSK1/2: -99.5 @ 2.5 GHz and 10 MHz BW
16QAM1/2: -94.29 @ 2.5 GHz and 10 MHz BW (RUT725)
Antenna Gain 14 dBi dual-pol MIMO
Antenna Type Panel antenna with pole mounting kit
Handover Hard / Optimized Handover
QoS Mechanism UGS, Real-Time-VR, Non Real-Time-VR, Best Effort, ERT-VR
Authentication EAP-TLS, EAP-TTLS-MSCHAPv2
Encryption 3 CCM-Mode 128-bit AES
Throughput HARQ UL and DL, up to Category 7
40 Mbps Total DL + UL
LEDs Power, LAN and WiMAX Activity
LAN 1 x RJ45 10/100 Base-T Ethernet
POE IEEE 802.3af-2003 Compliant
Electrical, Mechanical & Environmental:
Dimensions (H x W x D) 290mm x 240mm x 45mm
Mounting Pole Diameter 30 –50 mm
Weight 1.3 kg
Power Supply 36 –57VDC
Power Consumption < 6W
Operating Temperature - - 20º to 50º C
Storage Temperature - - 20º to 70º C
IP Rating IP65
Storage Humidity 5% to 95% Non-condensing