Tempur-Pedic SLEEPTRACKER ERGO Manual

STOP
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
STOP
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!
PLEASE READ INSTRUCTIONS
BEFORE SETUP OF NEW TEMPUR-PEDIC® SMARTBASE!

STEP 1 - BASE SETUP
Setup is now complete!
Only 1 processor (Base B) is used
for tandem/split setup.
For help installing the Tempur-Pedic®Sleeptracker®app, information can also be found at :
https://www.sleeptracker.com/getapp/tempur
U.S.: 1-844-309-3598
Canada: 1-800-887-4321
Mexico: 01-722-273-1810
a. Remove bases from packaging. Position bases to align HEAD/FOOT
ends the same direction. Note A/B position for the following steps.*
b. Locate printed materials (Base B only)*
c. Install legs
d. Connect power to base(s)
e. Insert remote batteries
f. Place units on their side with bottom towards each other for ease of
connections in step 2.*
STEP 2 SYNC CORD INSTALL (BASE A&B)
STEP 4 SLEEPTRACKER®PROCESSOR SETUP (BASE A ONLY)
STEP 5 SLEEPTRACKER®PROCESSOR SETUP (BASE B ONLY)
STEP 6 SLEEPTRACKER®APP SETUP (BASE B ONLY)
a. Disconnect male Battery
Backup Box Cable from female
Sleeptracker®Smart Cable.
a. Disconnect Sleeptracker®Sensor
Cable from Base A Sleeptracker®
Processor.
a. Connect Base A Sleeptracker®
Sensor Cable to Base B
Sleeptracker®Processor.
a. Test all functions on remote.
b. Connect male Sync Cord to
female Sleeptracker®Smart
Cable.
b. Route Sleeptracker®Sensor
cable through rubber conduit
and under Base A and B frames.
b. Route Base A Sleeptracker®Sensor
Cable through rubber conduit.
b. For Customer APP setup,
provide APP Setup Card from
printed materials (Base B card
only*).
c. Connect male Battery Backup
Box cable to female Sync Cord.
Discard additional sync cord,
only 1 is required.
d. Position bases back on their
legs to complete the remaining
steps. Assemble mattress
retainer bars and connecting
straps.
c. Disconnect Base A Sleeptracker®
Processor from USB Extension
Cable.
c. Call Tempur-Pedic Customer
Service for delivery conrmation.
ERGO EXTENDTM
+ SLEEPTRACKER®SYSTEM
SLEEPTRACKER®ERGOTM AND ERGO EXTENDTM TWIN LONG/SPLIT CA KING 2 UNIT SETUP
REFER TO IMAGES BELOW FOR STEPS 2-6 FOR SLEEPTRACKER®SETUP
Control box
USB
Extension
Cable
USB Ports Underbed Light
USB Ports
Massage
Motor
Sleeptracker®
Sensor
HEAD END
*Split Unit setup reference. Base A is
on right side.
Sleeptracker®
Smart Cable Underbed
Light Battery Backup Box Head Motor
APP Setup
Card
Sync Cord Connecting
Strap
Foot
Motor Massage
Motor
FOOT END
Sleeptracker®
Processor
ERGOTM
+ SLEEPTRACKER®SYSTEM
Underbed
Light
STEP 3 SLEEPTRACKER®SENSOR INSTAL (BASE A&B)
a. Remove Sleeptracker® Sensor
from twist ties.
b. Insert Sleeptracker®Sensor into
pocket.
c. Secure pocket to velcro strip
under head deck.