Tempur-Pedic ERGO PROSMART User manual

OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE
Tempur-Pedic Customer Service U.S. : 1-844-309-3597 | Canada : 1-800-887-4321 | Mexico: 01-722-273-1810
Service à la clientèle Tempur-Pedic É-U. : 1-844-309-3597 | Canada : 1-800-887-4321 | México: 01-722-273-1810
Servicio al Cliente Tempur-Pedic É-U. : 1-844-309-3597 | Canada : 1-800-887-4321 | México: 01-722-273-1810
MANUAL DEL PROPIETARIO
TEMPUR ERGO PROSMARTTM

table of contents
Safety Precautions and Usage Statements ......................................................1-4
Parts List ...................................................................................... 5
Base Overview ................................................................................ 6
Quick Reference Guide ..........................................................................7
Installation Guide ............................................................................8-10
Remote Control .............................................................................11-13
USB Charging .................................................................................14
SoundScapeTM Setup ............................................................................15
Connecting Strap ..............................................................................16
Syncing Two Bases.............................................................................17
Headboard Brackets (Not Included) .............................................................18
Emergency Battery Backup Strap ...............................................................19
Troubleshooting ..............................................................................20
Warranty ...................................................................................21-22

table des matières
Consignes de sécurité et directives d’utilisation ..............................................23-26
Liste des pièces .............................................................................. 27
Aperçu de la base ........................................................................... 28
Guide de référence rapide .................................................................... 29
Guide d’installation ........................................................................30-32
Télécommande ............................................................................33-35
Recharge USB ................................................................................36
Configuration SoundScapeTM.................................................................... 37
Attaches de raccordement ................................................................... 38
Synchronisation de deux bases ................................................................ 39
Fixations de tête de lit (non incluses) .......................................................... 40
Sangle des piles de secours .................................................................... 41
Dépannage ...................................................................................42
Garantie.................................................................................. 43-44

tabla de contenidos
Precauciones de Seguridad. .................................................................45-48
Lista de las Partes............................................................................. 49
Diagrama de la Base ..........................................................................50
Diagrama de Conexiones. .......................................................................51
Instalación de la Base ......................................................................52-53
Control Remoto ............................................................................54-56
Carga USB ....................................................................................58
Configuración de SoundScapeTM .................................................................59
Correas de Conexión ...........................................................................60
Sincronización de Dos Bases. ................................................................... 61
Guía de Instalación de Soportes de la Cabecera (Opcional) ........................................62
Correa de Respaldo de la Batería ...............................................................63
Solución de Problemas. ........................................................................64
Garantía....................................................................................65-66

1
safety precautions and usage statements
Attention: Important Safety Disclaimers
Read all instructions before using your TEMPUR ERGO PROSMARTTM Powered by Sleeptracker-AI®adjustable base.
SAVE THESE INSTRUCTIONS.
WARNING
To reduce the risk of shock, burns, fire or injury:
Always unplug the base from the electrical outlet before servicing any
part of the base. To reduce risk of electric shock, unplug the base before
cleaning. To safely disconnect, ensure the base is in a flat position with all
motors o, and unplug from power source.
Keep the power cord away from heated surfaces. Never operate the base
when the air openings are blocked. Keep air openings free of lint, hair and
the like. Do not drop or insert any object into any opening.
Discontinue use of the bed base and contact a qualified service center if: it
has a damaged cord or plug, is not working properly, or has been dropped
into water.
Only use this bed base for its intended use as described in this manual.
Do not use accessories/attachments that are not recommended by the
manufacturer.
Close supervision is required when the bed base is used by or near children,
convalescents or disabled persons.
Outlet Safety:
For optimal safety and operation, plug bed base into a
surge protector (not included).
The bed base should only be plugged directly into a wall outlet or surge
protector (recommended). Improper connection of the equipment can result
in the risk of electrical shock, electrical fire or faulty operation of this bed
base. If the plug does not fit your outlet, contact a qualified electrician to
install a suitable outlet. Unauthorized modification or failure to use a wall
outlet or surge protector could void the electrical portion of your warranty.
Warranty Warning:
Do not open or tamper with control box, motors, or remote (with the
exception of battery compartments). The warranty will be void if the internal
workings of these components are tampered with. For complete warranty
information refer to the warranty information section on pages 21-22.
In-Home Use and Hospital Disclaimer:
The TEMPUR ERGO PROSMARTTM Powered by Sleeptracker-AI®bed base is
designed solely for in-home use. This base was not designed as a hospital
bed and is not designed to meet hospital standards.
Do not use this base with TENT TYPE oxygen therapy equipment or
near explosive gases.
Children and Pets:
Children and pets can be crushed or killed if they become entrapped in
moving parts of the bed. Before you reposition the base, check to be sure
children and pets are not near or under the base. Do not teach children to
operate the remote. Engage child lockout on the remote before leaving the
room. (See page 13) Store the remote where children can't find it. Children
should not operate this product without adult supervision. To avoid injury,
children and pets should not be allowed to play on or under the bed.
Immediately dispose of all packaging materials as they may pose a
smothering risk to children and pets.
Safety Features:
Manual operation – If something gets caught in the platform when flattened,
you can manually raise the platform up by lifting at both the head and foot
to relieve pressure and allow for release.
Child-lockout – This remote control is programmed with a child-lock safety
feature. Information on activation and deactivation of this feature can be
found on the Remote Control page(s) and on the back of your remote
control.
Emergency stop – Stop the motion of the platform by pressing any button
on the remote control or by pushing the button on the Battery Backup Box
located underneath the base.
Power outage – Use the “Emergency Battery Backup Box” as a temporary
power source to get the base to a desired position. Instructions on how
to operate the Battery Backup Box are on the Emergency Battery Backup
page(s).
Power Ratings:
INPUT: AC 100–240V 50/60 HZ 2.0A
OUTPUT: DC 29V 2.0A
WATTS: 58W

2
Product Ratings:
The lift motors are not designed to operate continuously for more than two
[2] minutes in an eighteen [18] minute time period or approximately 10% duty
cycle. Attempting to circumvent or exceed this rating will shorten the life
expectancy of the product and may void the warranty.
The massage motors are not designed to operate continuously for more
that 30 minutes at a time. Please allow the massaging system to rest for 30
minutes after automatic massage shut o before restarting.
Weight Limits:
The recommended weight limits on the TEMPUR ERGOTM PROSMART +
SLEEPTRACKER-AI®SYSTEM are:
Twin Long / Full / Queen / King / Split CA King / CA King: 850 pounds.
Maximum weight the bed can support per person is 350 pounds with the
weight evenly distributed across the head and foot sections. This product
is not designed to support or lift this amount of weight in the head or foot
sections alone. NOTE: Exceeding the recommended weight restrictions could
damage your TEMPUR ERGOTM PROSMART + SLEEPTRACKER-AI®SYSTEM
and void your warranty. For best performance, you should enter and exit the
TEMPUR ERGOTM PROSMART + SLEEPTRACKER-AI®SYSTEM while it is in the
flat or fully lowered position.
TEMPUR ERGOTM PROSMART + SLEEPTRACKER-AI®SYSTEM fits easily inside
bed frames, furniture beds and platform beds that are certified to hold a
minimum of 900 pounds. If using this adjustable base without the legs
and placing directly on a bed frame or platform bed, cross-bed supports
(slats) are strongly recommended to ensure TEMPUR ERGOTM PROSMART +
SLEEPTRACKER-AI®SYSTEM maintains stability during operation.
Acoustics:
In normal base operation the wheels, which allow the bed to maintain its
distance from the wall, will make contact with the steel platform supports of
the base creating a contact noise. When entering, exiting or shifting weight
on the base, this contact noise may be audible as the wheels make contact.
This is normal.
Fabric Care:
To prolong the life of your fabric, protect from direct sunlight whenever
possible. For spot cleaning, wipe area with a light damp sponge or vacuum
with a soft brush attachment to remove particles. Keep at a minimum of
30cm (12 inches) away from direct heat sources.
For deeper cleaning, blot liquid spills with a clean dry cloth. Wipe with a clean
cloth dampened with warm water. Do not wet excessively. A soft bristle brush
may be used to remove ingrained soil. Avoid scratching by gentle brushing.
Wipe with a clean cloth dampened with warm water to remove residues after
brushing. Dry in shade away from direct heat.
If persistent marks remain visible after cleaning, seek professional advice.
safety precautions and usage statements
Exceeding this weight restriction could damage the bed
and/or cause injury and will void the warranty.
FCC Compliance:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
CAN ICES-3 (B)/NMB-3(B)

3
Tempur®Sleeptracker-AI®System
For Tempur Ergo ProSmartTM
System Components
Tempur®Sleeptracker-AI®Sleep Monitoring System Model STS-60 / STS-60A:
- One Tempur®Sleeptracker-AI®Processor Unit
- One or two Tempur®Sleeptracker-AI®Sensors*
Safety and Warranty Information
*Note: the number of sensor units included depends on the particular Tempur
ErgoTM PROSMART + Sleeptracker-AI®System size purchased.
Specifications
Tempur®Sleeptracker-AI®Sleep Monitoring System Model STS-60 / STS-60A:
- Input Power: 5V DC, 1.5A
WLAN:
IEEE802.11a/b/g/n/ac
Wi-Fi frequency range:
2.4 GHz ISM Bands 2.412-2.472 GHz
5.15-5.25 GHz (FCC UNII-low band) for US/Canada and Europe
5.25-5.35 GHz (FCC UNII-middle band) for US/Canada and Europe
5.47-5.725 GHz for Europe 5.725-5.825 GHz (FCC UNII-high band) for US/
Canada
Wi-Fi AP channel:
802.11b:
USA, Canada and Taiwan – 1 ~ 11
Most European Countries – 1 ~ 13
802.11g:
USA and Canada – 1 ~ 11
Most European Countries – 1 ~ 13
802.11n:
USA and Canada – 1 ~ 11
Most European Countries – 1 ~ 13 802.11a:
USA – 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136,
140, 149, 153, 157, 161, 165
Output Power (Board Level Limit):
2.4G
Min Typ Max Unit
11b (11Mbps) @EVM<35% 14 16 18 dBM
11g (54Mbps) @EVM≦-27 dB 12 14 16 dBM
11n (HT20 MCS7) @EVM≦-28 dB 11 13 15 dBM
11n (HT40 MCS7) @EVM≦-28 dB 10 12 14 dBM
5G
Min Typ Max Unit
11a (54Mbps) @EVM≦-27 dB 11 13 15 dBm
11n (HT20 MCS7) @EVM≦-28 dB 8 10 15 dBm
11n (HT40 MCS7) @EVM≦-28 dB 8 10 12 dBm
11ac (VHT20 MCS8) @EVM≦-30 dB 8 10 12 dBm
11ac (VHT40 MCS9) @EVM≦-32 dB 7 9 11 dBm
11ac (VHT80 MCS9) @EVM≦-32 dB 6 8 10 dBm
Bluetooth Standard:
BT4.2+Enhanced Data Rate (EDR)
Bluetooth 5 support
Bluetooth frequency range:
2402MHz~2483MHz
Output Power:
Min Typ Max Unit
BDR 0 2 4 dBm
EDR -4 -1 1 dBm
Low Energy 0 2 4 dBm
Certifications:
- FCC Part 15B, FCC Part 15C
- ISED ICES-3(B)/NMB-3(B), RSS-Gen, RSS-102, RSS-210
© 2023 Tempur Sealy International, Inc.
All rights reserved. Tempur-Pedic is a registered trademark of Tempur Sealy
International, Inc. TEMPUR ERGOTM PROSMART is a trademark of Tempur
Sealy International, Inc.
© 2005–2023 Fullpower Technologies, Inc.
All rights reserved. U.S. and international patents granted and pending.
Sleeptracker-AI®is a trademark of Fullpower Technologies, Inc., registered in
the U.S. and other countries.
For assistance visit our web site: www.sleeptracker.com
Services and app availability are subject to change at any time, may not be
available in all areas and may require separate subscriptions.
This product is not a medical device and should not be used to diagnose or
treat any medical condition.
Designed in Santa Cruz, California
Made in China
safety precautions and usage statements

4
safety precautions and usage statements
System Requirements:
• Mobile device running iOS or Android
• Existing Wi-Fi network
Tempur®Sleeptracker-AI®App from Fullpower Technologies, available on the
Apple App Store or on Google Play. Requires Wi-Fi connection to your home
network, and Internet access via a router or modem.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.
and other countries. App Store is a service mark of Apple Inc., registered in
the U.S. and other countries. iOS is a trademark or registered trademark of
Cisco in the U.S. and other countries and is used under license.
Google Play, Android and the Google Play logo are trademarks of Google Inc.
100–240 V AC 50/60 Hz
FCC ID: 2AF2O-STS60
IC: 20700-STS60
Tempur-Pedic North America, Inc.
1000 Tempur Way
Lexington, KY 40511
Tempur-Pedic Canada
145 Milner Ave.
Scarborough, Ontario M1S 3R1
FCC Certification Statement
This equipment complies with Part 15 of the FCC Rules. Operation of this
equipment is subject to the following two conditions: (1) the equipment may
not cause harmful interference, and (2) the equipment must accept any
interference that might cause undesired operation.
Important: Any changes or modifications not expressly approved by Tempur
Sealy International (”Tempur”) could void the electromagnetic compatibility
compliance and negate your authority to operate this equipment.
This equipment was tested for FCC compliance under conditions that
included the use of Tempur peripheral devices and Tempur cables and
connectors between system components. It is important that you use Tempur
cables and connectors between system components to reduce the possibility
of causing interference to radios, television sets, and other electronic devices.
You can obtain proper Tempur cables and connectors through an Tempur-
authorized dealer.
Responsible party (contact for FCC matters only):
Tempur-Pedic North America, Inc.
1000 Tempur Way
Lexington, KY 40511
Tempur®Sleeptracker-AI®Sleep Monitoring System Model STS-60 / STS-60A:
FCC ID: 2AF2O-STS60
ISED Statement of Compliance
This device complies with ISED license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. This device
complies with ICES-003 Class B specifications of Industry Canada.
Responsible party (contact for ISED matters only):
1390658 Ontario Inc (Tempur Canada)
145 Milner Ave.
Scarborough, Ontario
M1S 3R1
Tempur®Sleeptracker-AI®Sleep Monitoring System Model STS-60 / STS-60A:
IC: 20700-STS60.
Exposure to Radio Frequency Energy
This equipment complies with radiation exposure limits set forth in the FCC’s
KDB 447498 and ISED RSS-102 standard for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of
20cm (about 8 inches) between the radiator and your body. This equipment
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Pacemaker Notice
If you use a medical device such as a pacemaker or implantable cardioverter-
defibrillator (ICD), please consult your physician before using this product.

5
parts list
A) B)* C)
D) E) **
)‡* )
All electronics and components that need to be installed are
located in boxes under the base or attached to the frame.
A) Wireless Remote Control (1)
AAA Batteries (2)
B) Mattress Retainer Bar (1)*
C) Legs (6)
D) Power Cord (1)
E) Power Supply (1)
F) Battery Backup Strap (1) **
(9 Volt alkaline batteries not included)
G) Connecting Strap ‡*
Miscellaneous Parts (not included):
H) Surge Protector (1)
I) 9 Volt alkaline batteries (2)
Before discarding the packing materials, ensure all the parts are accounted for.
A
D
G
B
E
C
F
* These items are attached to the base for shipping purposes.
Carefully remove from base and set aside.
** Leave connected to the Power Supply.
‡ Only included in Twin Long and Cal King Split
*

6
base overview
Foot Motor
Head Motor
Lumbar
Motor
Tempur®
Sleeptracker-AI®
Processor
Control
Box
USB Charger
USB
Charger
Massage
Transducers
Massage
Transducers
Underbed Light
Underbed Light
Underbed
Light
Tempur®
Sleeptracker-AI®Sensor
Soundbar
Tempur®
Sleeptracker-AI®Sensor
To access all the features of your smart base, please download the Tempur-Pedic Sleeptracker-AI®app and setup using
the QR code found on the back of the remote.

7
Not to scale. For illustration purposes only. Read all instructions before beginning installation.
quick reference guide
Remote
Control
Download the
App today
Battery
Backup Strap
Tempur®
Sleeptracker-AI®
Processor
USB Extension
Underbed Lighting
USB Charger
Massage Transducer
Splitter Cable
Massage
Transducers
LED Brand Badge
Soundbar
Speaker
Communication Line
Audio Cable
Lumbar Motor
Foot Motor
Head Motor
Control Box
Aux Out
Input Cable Power Supply Power Cord
Tempur®
Sleeptracker-AI®Sensor

8
installation guide
STEP 1
STEP 4
STEP 2
Always use two people when setting up the base.
Place the bed base box in a desired location with the bottom
of the box facing up.
Remove the binding straps and packing materials, making
sure not to puncture the box with any sharp objects.
Remove the bed base from the box. Unfold the bed making
sure to keep the bottom of the bed facing upwards. Remove
all accessories and interior packaging and identify items
included in parts list above. Remove the clear protective
sheet from the soundbar.
STEP 3
To sync two bases see detailed installation
instructions on pages 16-17.
To install Headboard Brackets (sold separately)
see instructions on page 18.
It is recommended to leave the battery
backup strap attached to the power
supply for use when needed. 2 9V
alkaline batteries (not included) will be
required for its use.
Legs are shipped fully assembled. To install the legs, check
to make sure all segments are assembled together tightly.
Alternative heights in 3" increments can be achieved by
removing leg segments from the top of the leg accessory.
Thread the leg into the frame, and tighten by hand. Do not over
tighten.

9
installation guide
STEP 7
STEP 8
STEP 9
STEP 10
Carefully flip the base over on to its legs. Important: Two
people are required to move the bed base. Do not drag
across the floor. Do not rest frame on its side, excessive
pressure may damage the legs.
Plug the Power Cord into a power source. A surge protector is
recommended.
Ensure that batteries are correctly installed in the remote.
Quickly test remote functions to verify proper setup before
placing mattress on base. Return the base to a FLAT position
before placing the mattress on top.
To install the mattress retainer bar, insert each end of the bar
into the holes at the foot of the platform.
STEP 5
STEP 6
Uncoil Input Cable (connected to Control
Box’s power port) and plug into Power
Supply.
Uncoil the Power Cord and connect to
the Power Supply. Place Power Supply
on the ground and extend from the
base. Ensure that the Power Supply and
all attached cords are directed toward
the desired surge protector.

10
installation guide
STEP 11
STEP 12
STEP 13
Using the remote, move the head of
the base to its full upright position.
Confirm that the LED on the black
Tempur®Sleeptracker-AI®processor
is blinking green. This may take up
to 90 seconds after connecting
power to the base. This indicates
that the processor is powered up
and ready to connect to a WiFi
network.
or
To complete the Smart Base setup, you will need to
download the Tempur®Sleeptracker-AI®App and follow the
in-app prompts. Once the app is connected, it will allow
access to the full functionality of your new Tempur Ergo
ProSmartTM Base.
Setup is now complete! Test all functions on remote.
The customer should scan the
QR code on the remote control
packaging or on the rear side label
of the remote control to set up the
Tempur®Sleeptracker-AI®App.
IMPORTANT!: For your safety, read the owner’s manual carefully
and completely before operating this product. Electric shock
may occur if electrical components are not installed or operated
according to these guidelines.

11
Remote control arrives paired to the adjustable base.
Two (2) AAA batteries are required to operate the remote.
remote control
ADJUST
Head Position Adjustments
Use to raise and lower the head section of your
adjustable base.
Foot Position Adjustments
Use to raise and lower the foot section of your
adjustable base.
Lumbar Adjustments
Use to increase or decrease lumbar support.
PRESET
Zero-G®‡
Adjusts your legs to relieve pressure o the lower back.
Flat *
One-Touch Flat lowers head and foot to flat position
and turns o massage (if running).
TV in Bed Preset Position ‡
Brings head and foot into position for viewing TV.
QuietMode™ Preset Position ‡
Help relieve snoring for you or your partner with the
push of a button, gently tilting the mattress position to
help reduce snoring.
Favorite 1 & 2 Preset Position ‡
Reprogrammable Preset Positions.
Underbed LED lighting *
Press to turn on/o underbed LED lighting. Press
and hold for three (3) seconds to turn o LED brand
badge.
* Not user programmable.
‡ Can be reprogrammed to user desired position.
The Zero-G®, TV in Bed, Anti-Snore, and Favorite 1 in bed presets
can be re-programmed to any position chosen by the user.
Simply adjust the bed to the desired position, then press and
hold any of the 4 buttons down until the remote backlight flashes
twice. The button is now re-programmed.
To restore the buttons to their original positions, press and hold
the One-touch Flat and Zero-G®buttons simultaneously for 5
seconds. The remote backlight will flash twice to indicate the
original positions have been restored.

12
MASSAGE
Head Zone Massage Intensity
Cycles Head Massage through 3 intensity levels when
pressed while in massage mode (Low > Med > High >
O) Adjusts Head Massage bass level output through 3
levels when pressed while in SoundScapeTM mode (Low >
Med > High)
Foot Zone Massage Intensity
Cycles Foot Massage through 3 intensity levels while in
massage mode (Low > Med > High > O)
Adjusts Foot Massage bass level output through 3 levels
when pressed while in SoundScapeTM mode (Low > Med >
High)
Massage / SoundScapeTM* Mode Control**
Cycles massage wave modes when pressed while in
massage mode (1 > 2 > 3 > O). Intensity massage
default is low. Once activated, massage will automatically
shut o after 30 minutes.
*Press and hold for 3 seconds to switch from Massage to
SoundScapeTM mode or vice versa. During mode switch,
LED 1-2-3 will flash for transition to SoundScapeTM mode,
followed by verbal cue from soundbar 'Sound Mode' or
'Massage Mode'. Default mode is massage mode.
Adjusts Head and Foot Massage bass level output
through 3 levels when pressed while in SoundScapeTM
mode (Low > Med > High)
remote control
Remote control arrives paired to the adjustable base.
Two (2) AAA batteries are required to operate the remote.
28 Hz Frequency Setting (Body Relax)**
Changes current massage frequency output to 28Hz at
current intensity levels when pressed while in massage
mode. If massage is o, turns on both head/foot
massage zones at low intensity, 28Hz frequency, when
pressed while in massage mode.
40 Hz Frequency Setting (Mind Relax)**
Changes current massage frequency output to 40Hz at
current intensity levels when pressed while in massage
mode. If massage is o, turns on both head/foot
massage zones at low intensity, 40Hz frequency, when
pressed while in massage mode.
** For more frequency options and benefits related to
massage, download and access additional functionality
in the Tempur®Sleeptracker-AI®App.

13
Child Lock Feature
Remote Pairing
Activate Child Lock
Deactivate Child Lock
remote control
Test all remote functions. If the remote buttons do not impact the
adjustable base movements, please repeat the process again or call
customer service: U.S. 1-800-499-1965 | Canada 1-800-268-4414
STEP 1
STEP 2
The original remote that comes in the box is already paired to the
adjustable base. No further action is required. In the event that the
remote is not paired with the base, follow the steps below. Children and pets can be crushed or killed in moving parts of the bed!
For safety purposes, the child lock function locks the remote control
to prevent any accidental button presses and bed movements.
Engage child lock on the remote control before leaving the room.
STEP 3
Remove rear cover of the remote control by sliding it down to expose
the PAIR button. Unplug the Power Cord from your power outlet.
Wait 1 minute, then plug it back in to your power outlet. Soundbar
will provide verbal cue 'Bluetooth Mode' to indicate it is ready for
pairing. Perform Step 2 within 10 seconds, while the control box
light is flashing.
Power Cord
Power Supply
Press and hold the PAIR button on the back of the
remote. The PAIR button will illuminate and start
to flash. When the PAIR button stops flashing, the
LED light on the control box will stop flashing.
Soundbar will provide verbal cue 'Connected' to
indicate the remote has paired successfully to the
control box. Release the PAIR button.
Press/hold dedicated Child Lock button for three (3)
seconds.
The remote LED will flash twice to confirm activation.
When any button is pressed on the remote while
in child lock mode, the LED illuminates for two (2)
seconds or while button is pressed.
*Child Lock feature will be deactivated when batteries
are removed.
Press/hold dedicated Child Lock button and the
Underbed Lighting button together for three (3)
seconds.
The remote LED will flash once to indicate the remote
is no longer in Child Lock. The remote and adjustable
base will work normally.
+
WARNING

14
The Type-A USB connector is a
standard USB port, used for standard
cable connection interface for personal
computers and consumer electronics
devices.
The Type-C USB connector is a smaller
USB port.
TYPE-A CONNECTOR (STANDARD USB) TYPE-C CONNECTOR
USB Charging
The USB charger is configured with 2 connectors, Type-A and Type-C connector.

15
SoundScapeTM Setup
Connect any smart device with Bluetooth®capability to wirelessly stream music.
STEP 1 STEP 2
OPTIONAL
Locate Bluetooth®settings on the smart device. Select the Bluetooth®
ID that begins with "Tempur ProSmart xxxxx". For multiple unit
setups, the specific Bluetooth®ID can be found on the tag or on the
soundbar itself located underneath the head deck.
Once connected, use any music
player on the smart device to
wirelessly stream music.
Use the smart device to control
volume level. To further customize
volume levels, see OPTIONAL
section below.
To adjust bass level output from the massage motors while
in music mode:
Press Head and Foot Zone Massage Intensity buttons
to adjust intensity of the massage transducers (amount
of sensation) while in music mode (Low > Med >
High) to control each zone separately. Press Massage
/ SoundScapeTM Mode Control button to adjust both
head and foot zones together.
To switch devices:
Turn o Bluetooth®on active device OR select the active device in
your Bluetooth®settings and press “forget this device”. You may
now pair another device.
To switch between SoundScapeTM mode and Massage
mode:
Press and hold mode button on the remote control for three (3)
seconds. Audio cue from the soundbar will announce the current
mode.
To sync two audio systems (TL or CKS):
See page 17.
For assistance setting up a Bluetooth®connection or
operating music player, refer to your smart device's owners
manual or contact the manufacturer directly.

16
connecting strap
With the bases in their desired
location, slightly loosen both
legs to allow the strap to fit on
the leg bolt, between the leg
washer and frame.
Slide side (a) of the Connecting Strap onto leg bolt. Swing the
strap and connect side (b) to the leg bolt. Secure the strap by
shifting to the left.
Re-tighten legs. Do not over tighten. Use the remaining strap
and repeat on other end of the base.
STEP 2
STEP 1
STEP 3
a b
If any split setup is being installed, plastic Connecting Straps are provided (one per base) to secure the
bases together.