Tempur-Pedic 99300728-b User manual

99300728-b EDR10679 5/06
Serial No.
OWNERS MANUAL

CONTENTS
Advisory ............................................................................................................ 4-5
Acoustics .............................................................................................................. 6
Installation ....................................................................................................... 7-12
Tempur-Ergo Hand Control ............................................................................... 13
Hand Control Programming ......................................................................... 14-18
Accessories ........................................................................................................ 19
Troubleshooting ................................................................................................. 20
1-2-20 Warranty............................................................................................. 21-22
Copyright © 2006 Tempur-Pedic, Inc.
Copyright © 2006 Leggett & Platt, Inc.
All Rights Reserved
Tempur-Pedic
®
Owners Manual
22
1-2-20 WARRANTY
Repairs to or replacement of an adjustable
bed or its components under the terms of
this limited warranty will apply to the original
warranty period and will not serve to extend
such period.
The decision to repair or to replace defective
parts under this warranty shall be made, or
cause to be made, by L&P at its option and
in its sole discretion.
Repair or replacement shall be the sole
remedy of the purchaser. There shall be no
liability on the part of L&P for any special,
indirect, incidental, or consequential
damages or for any other damage, claim, or
loss not expressly covered by the terms of
this warranty.
This limited warranty does not include
reimbursement for inconvenience, removal,
installation, setup time, loss of use, shipping,
or any other costs or expenses. Leggett &
Platt or its service technicians shall not be
responsible for moving furniture, removing
headboards & footboards or any other items
in order to perform service on the adjustable
bed.
It is the sole responsibility of the purchaser
to provide adequate space and accessibility
to the adjustable bed. In the event that the
technician is unable to perform service due
to lack of accessibility, the service call will be
billed to the purchaser and the service will
have to be rescheduled.
L&P makes no other warranty whatever,
express or implied, and all implied
warranties of merchantability and fitness
for a particular purpose are disclaimed by
L&P and excluded from this agreement.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation or
exclusion may not apply to every purchaser.
This warranty gives the purchaser specific
legal rights, and the purchaser may also
have other rights, which may vary from state
to state. This warranty is valid in all 50
states, Puerto Rico, and Canada.
WARRANTY INFORMATION
Leggett & Platt
Adjustable Bed Customer Service Center
PO Box 668
Lexington, NC 27293
800-888-3078
Warranty Service E-mail: [email protected]
Please do not contact retail dealer or any other service personnel.
www.lpadjustablebeds.com

Tempur-Pedic
®
Owners Manual
4
ADVISORY
ELECTRICAL GROUNDING
This product is equipped with a polarized,
grounded electrical power cord. The
power cord will only fit into a grounded,
electrical surge protection device (not
included) or a grounded electrical outlet.
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
This Tempur-Pedic® adjustable bed has been quality engineered with design features to
assure comfort and safety when operated properly.
WARRANTY WARNING
Do not open any control boxes, motors or
hand control devices (with the exception
of the hand control and power down box
battery compartments). The product
warranty will be void if these components
are tampered with. Do not attempt to alter
component wiring or adjust or modify the
structure of the product in any way or the
warranty will be void. Any repair or
replacement of adjustable bed parts must
be performed by authorized personnel.
LUBRICATION
This product is designed to be
maintenance free. The lift motors are
permanently lubricated and sealed—no
additional lubrication is required. Do not
apply lubricant to lift motor lead screws or
any nylon nuts or the bed may
inadvertently creep downward from the
elevated position.
PRODUCT RATINGS
The bed lift motors are not designed for
continuous use. Reliable operation and full
life expectancy will be realized as long as
the lift motors do not operate any more
than five (5) minutes over a thirty (30)
minute period, or approximately 15% duty
cycle. Note: massage equipped beds are
not designed for continuous, extended
massage operation. Massage systems are
rated for a maximum of 2 hours of use
within any 6 hour period. Any attempt to
circumvent or exceed product ratings will
shorten the life expectancy of the product
and may void the warranty.
The recommended weight restrictions for
Tempur-Pedic® adjustable beds are as
follows: Twin-300 lbs (136.07kg), Full-375
lbs (170.09kg) and Queen-425 lbs
(192.77kg). The bed will structurally
support the recommended weights
distributed evenly across the head and
foot sections. This product is not designed
to support or lift this amount in the head or
foot sections alone. Note: exceeding the
recommended weight restrictions could
damage the adjustable bed and void the
warranty.
For best performance, consumers should
enter and exit the adjustable bed with the
bed in the flat (horizontal) position. DO NOT
SIT ON THE HEAD OR FOOT SECTIONS
WHILE IN THE RAISED POSITION.
IMPORTANT INFORMATION
FOR OPTIMUM ADJUSTABLE BED
OPERATION, USE A GROUNDED,
ELECTRICAL SURGE PROTECTION
DEVICE (NOT INCLUDED). FAILURE TO
USE A SURGE PROTECTION DEVICE
COULD COMPROMISE SAFETY OR
CAUSE PRODUCT MALFUNCTION.
Tempur-Pedic
®
Owners Manual
21
1-2-20 WARRANTY
FULL 1 YEAR WARRANTY
This adjustable bed is warranted against
defects in the workmanship or materials for
a period of one (1) year from the warranty
commencement date. Upon notice during
the first year after the warranty
commencement date, L&P will repair or
replace (at no cost to the purchaser) any
defective adjustable bed part, and L&P will
pay all authorized labor and transportation
costs associated with the repair or
replacement of any parts found to be
defective.
2 YEAR LIMITED WARRANTY
During the second year from the warranty
commencement date, upon receipt of notice,
L&P will replace any adjustable bed part
found to be defective. This limited two (2)
year warranty shall not apply unless the
defective part is returned to L&P within ten
(10) days of purchaser’s receipt of the
replacement part. Purchaser shall pay all
service and transportation costs related to
the replacement of the defective part.
20 YEAR LIMITED WARRANTY
Upon notice during the third through the
twentieth years from the warranty
commencement date, L&P will replace, upon
terms and conditions set forth in this
paragraph, any mechanical bed part found to
be defective. Electronics, electrical
components, drive motors and massage
motors are excluded. Purchaser shall pay
1/18 of the then current replacement cost of
the defective part multiplied by the number
of years after two (2) years from the
Leggett & Platt, Incorporated (“L&P”) warrants this adjustable bed to the consumer who is the
original purchaser (the “purchaser”), subject to the terms and conditions set forth herein. This
warranty begins on the “warranty commencement date” which is the date of purchase for new
unused beds and the date of manufacture for beds that have been used as floor or display
models. Thus, on a floor model bed, the warranty is a portion of the limited 20 year warranty.
warranty commencement date, and L&P
shall bear the remainder of the cost of the
replacement part. This twenty (20) year
warranty shall not apply unless the defective
part is returned to L&P within ten (10) days of
purchaser’s receipt of the replacement part.
Purchaser shall pay all service and
transportation costs related to the
replacement of the defective part. After the
twentieth year, purchaser shall bear the
entire cost of repair and replacement of all
parts and materials, including labor and
transportation.
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any
damage caused by the purchaser; (b) if there
has been any repair or replacement of
adjustable bed parts by an unauthorized
person; (c) if the adjustable bed has been
mishandled (whether in transit or by other
means), subjected to physical or electrical
abuse or misuse, or otherwise operated in
any manner inconsistent with the operation
and maintenance procedures outlined in the
Owners Manual and this warranty; (d) to
damage to mattresses, fabric, cables,
electrical cords or items supplied by dealers.
Contact the dealer for warranty information
on these items; (e) if there has been any
modification of the adjustable bed without
prior written consent by L&P; (f) to costs for
unnecessary service calls, including costs for
in-home service calls solely for the purpose
of educating the consumer about the
adjustable bed or finding an unsatisfactory
power connection; (g) if the recommended
weight restrictions are not followed (300-
Twin; 375-Full; 425-Queen), the warranty will
be void.
Continued on back of page...

Tempur-Pedic
®
Owners Manual
5
LOCKING CASTER
DETAIL
LOCK
ADVISORY
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
This Tempur-Pedic® adjustable bed has been quality engineered with design features to
assure comfort and safety when operated properly.
IMPORTANT INFORMATION
SMALL CHILDREN / PETS WARNING
After the bed is unboxed, immediately
dispose of packaging material as it can
smother small children and pets. To avoid
injury, children or pets should not be
allowed to play under or on the bed.
Children should not operate this bed
without adult supervision.
HOSPITAL USE DISCLAIMER
This bed is designed for in-home use
only. It is not approved for hospital use
and does not comply with hospital
standards. Do not use this bed with tent
type oxygen therapy equipment, or use
near explosive gases.
PACEMAKER WARNING
This product produces a vibrating
sensation. It is possible that individuals
with heart-assist pacemakers may
experience a sensation similar to exercise.
Consult physician for complete
information.
SERVICE REQUIREMENTS
Service technicians are not responsible for
moving furniture, removing headboards
and footboards or any items required to
perform maintenance on your adjustable
bed. In the event the technician is unable
to perform service due to lack of
accessibility, the service call will be billed
to the purchaser and the service will have
to be rescheduled.
FCC COMPLIANCE
Electrical components are rated for 110/
120 voltage, 60Hz, 3.9 amp. Components
meet Class B digital device rating (Part 15,
FCC rules) for residential use. Tempur-
Pedic®adjustable beds generate, use and
may radiate radio frequency energy. Radio
communication may be affected if not
installed and operated as recommended in
this manual.
Radio frequency = 310MHz.
LOCKING CASTER SAFETY FEATURE
Tempur-Pedic®adjustable beds are
equipped with locking casters to prohibit
the bed from movement. For best results,
place rubber caster cups under locking
casters when the bed is located on smooth
or hard surface flooring—it is possible for
locking caster equipped beds to slide
without the use of rubber caster cups.
To activate locking casters, push down on
the lock tab. To disengage the locking
mechanism, push up on the lock tab (see
illustration below).
Tempur-Pedic
®
Owners Manual
20
TROUBLESHOOTING
In the event the Tempur-Pedic® adjustable bed fails to operate, investigate the symptoms
and possible solutions provided in the chart below:
SYMPTOM
• Verify power cord is plugged into a working,
grounded electrical outlet. A grounded,
electrical surge protection device is recommended.
Test outlet by plugging in another working appliance.
• Program the hand control (see Hand Control
Programming Section).
• Unplug power cord, wait 30 seconds and plug in to
reset electronic components.
• Electrical circuit breaker may be tripped. Check
electrical service breaker box to verify.
• Defective surge protection device or electrical outlet.
Test outlet by plugging in another working appliance.
• Replace batteries in the hand control.
• Bed mechanism may be obstructed. Elevate bed and
check for obstruction. Remove obstruction.
• Head section may be too close to the wall.
• Headboard may be too close the edge of the mattress.
Verify a 1.5” (38.1mm) to 2” (50.8mm) distance
between headboard brackets and mattress. Adjust if
required.
• Verify headboard brackets were removed during
installation. Remove headboard brackets if still
attached to the underneath side of bed.
• If bed is located on hard surface flooring, place carpet
pieces or rubber caster cups under each leg or caster
of the bed. (See accessory sheet, included with this
product, for rubber caster cup order information.)
• Elevate the head or foot section a short distance (with
the hand control) to realign the lift/lower mechanisms
with the bed support platform.
• Verify that bed is not positioned against a wall,
nightstand, or other object that may cause vibration or
noise.
• If adjustable bed is installed over a bed frame, verify
massage motors are not causing bed frame (or bed
frame components) to vibrate.
• Verify that headboard attachment hardware is
tightened firmly (if used).
Excessive massage motor noise.
Head or foot section will elevate, but will not
return to the horizontal (flat) position.
Hand control will not illuminate.
No features of the adjustable bed will activate.
Hand control illuminates and appears to be
operable, but will not activate bed.
SOLUTION

Tempur-Pedic
®
Owners Manual
6
ACOUSTICS
LIFTING/LOWERING MECHANISMS
The lift/lower feature will emit a minimal
humming sound during operation. This is
normal.
During operation, the lift arm wheels make
contact with the platform support of the
bed. This applies slight tension on the
moving components and resonance is
reduced to a minimum level. If excessive
noise or vibration is experienced, reverse
the movement action (up or down) of the
bed with the hand control. This should
realign the bed’s activating mechanisms to
the proper operational position.
“Rubbing” noises may occur during lifting/
lowering due to friction between the
mattress and the basecover foundation.
This should go away after a breaking-in
period. If it continues, apply talc powder
between the two surfaces.
MASSAGE OPERATION
The massage feature will emit a minimal
tone during operation. This is normal.
When the massage level is increased,
motor resonance will intensify accordingly.
LOCATION ENVIRONMENT
The level of sound experienced during
operation is directly related to the location
environment. For example, when a bed is
located on a hardwood floor with the
massage feature in operation, a vibrating
tone will be audible. To minimize this
resonance, place a piece of carpet—or
optional rubber caster cups—under each
leg or caster of the bed. Refer to the
Accessories section of this manual for
rubber caster cup order information.
It is possible to experience vibration or
noise from the headboard brackets,
headboards or footboards if mounting
bolts are not firmly tightened.
Tempur-Pedic
®
Owners Manual
19
4B1209
ACCESSORIES
4B2101
4B2100
3” 4”
Tempur-Pedic®OPTIONAL EQUIPMENT
Contact customer service toll free (800-888-3078) to order the accessories indicated in the
chart below.
ACCESSORY DESCRIPTION
1” Bed Riser Kit (5” Legs - set of 4) 4B2100
3” Bed Riser Kit (7” Legs - set of 4) 4B2101
Swing-away Hinges 4B1209
Rubber Caster Cups (set of 4) 4B1034
CODE
5”
7”
4B1034

Tempur-Pedic
®
Owners Manual
7
MATTRESS
RETAINER
INSTALLATION
1. Before discarding any packing materials,
check the adjustable bed shipping carton
and verify the following items are included:
• (1) Mattress Retainer
• (1) Mattress Retainer Hardware Kit
• (4) Bed Legs
• (4) Locking Leg Casters
• (2) Headboard Bracket Assemblies
• (1) Headboard Bracket Hardware Kit
• (1) Hand Control
• (1) Owners Manual
• (1) Registration Card
For installation and setup, complete the numbered procedure indicated below and on the
following pages:
HEADBOARD BRACKET
HARDWARE KIT
(hardware: 16 pieces)
LEG
(4 pieces)
LOCKING
LEG CASTER
(4 pieces)
MATTRESS RETAINER
HARDWARE KIT
(hardware: 16 pieces)
HEADBOARD BRACKET ASSEMBLIES
Queen size shown—twin size (or smaller) headboard
brackets are not equipped with angle brace.
(4 pieces, 2 assemblies)
ANGLE BRACE
TEMPUR-ERGO
HAND CONTROL
Tempur-Pedic
®
Owners Manual
18
TEMPUR-ERGO PROGRAMMING separating 2 beds
STEP 1
Locate the power down box for bed 1 and
press the learn button for 1 second and
release (FIGURE 13).
The six step procedure below is required to separate 2 hand controls from operating 2 beds.
One hand control per bed operation will result. Before beginning, make certain the beds are
plugged into a working grounded electrical outlet.
STEP 2
On hand control 1 simultaneously press
and hold the position 1 and off buttons
(FIGURE 14). The transmission indicator
light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
STEP 3
Repeat Step 1 and Step 2 with hand control 1.
Note: wait 90 seconds before proceeding to
Step 4.
STEP 4
Locate the power down box for bed 2 and
press the learn button for 1 second and
release (FIGURE 13).
STEP 6
Repeat Step 4 and Step 5 with hand
control 2.
Independent hand control operation is
now restored (hand control 1 operating
bed 1; hand control 2 operating bed 2).
HAND
CONTROL 1
BED 1
HAND
CONTROL 2
BED 2
STEP 5
On hand control 2, simultaneously press and
hold the position 1 and the off buttons. The
transmission indicator light will flash slowly
and then flash rapidly. Continue to hold for 5
seconds and then release the buttons
(FIGURE 14).
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
NOTE
FIGURE 14
OFF
BUTTON
TRANSMISSION
INDICATOR
LIGHT
POSITION 1
BUTTON
POWER
DOWN BOX
LEARN
BUTTON
FIGURE 13: Power down box learn button.

Tempur-Pedic
®
Owners Manual
8
INSTALLATION
2. Carefully lift the bed base frame from the
shipping carton, keeping the unit top-side-
down.
3. Install (4) legs into the base frame. Simply
screw each leg into a tapped hole at each
corner of the base frame (FIGURE 1). Insert
casters into the bottom of each bed leg.
4. Remove and extend out power cord from
the protective packaging.
POWER CORDS MUST NOT INTERFERE
WITH ANY ADJUSTABLE BED
MECHANISMS. 6. Remove the plastic packaging from the bed
base frame. Carefully rotate the base frame
over to position the bed top-side-up.
7. Plug power cord into a working, grounded
electrical outlet. Note: an electrical surge
protection device is recommended (not
included).
8. Install batteries in hand control (4-AAA size,
included). Briefly activate all functions of
the bed with the hand control to verify all
features are in working order. If bed does
not operate, refer to the Hand Control
Programming instructions beginning on
page 14.
9. Return bed to the level position.
FIGURE 1: Leg and caster installation.
LEGS – SCREW INTO
TAPPED HOLE AT
EACH CORNER
CASTERS – PRESS-FIT
INTO BOTTOM OF LEGS
5. Install (2) 9 volt batteries into the power
down box (FIGURES 2 and 3).
FIGURE 2: Power down box battery compartment door
removal.
FIGURE 3: Power down box battery installation and battery
compartment door reinstallation.
PRESS IN (SLIGHTLY) AND
PUSH DOWN TO REMOVE
BATTERY COMPARTMENT
DOOR
POWER DOWN BOX
BATTERY COMPARTMENT DOOR
BATTERY ORIENTATION IS
INDICATED INSIDE BATTERY
COMPARTMENT
DOOR INSTALLATION:
PRESS COMPARTMENT DOOR
AGAINST THE BATTERY ENDS, TABS
SLIDE DOOR UP AND IN
TO ENGAGE THE DOOR TABS
Tempur-Pedic
®
Owners Manual
17
TEMPUR-ERGO PROGRAMMING 2 hand controls - 2 beds
STEP 1
Locate the power down box for bed 1 and
press the learn button for 1 second and
release (FIGURE 13).
The six step procedure below is required to program 2 hand controls to operate 2 beds. Before
beginning, make certain the beds are plugged into a working grounded electrical outlet.
STEP 2
On hand control 1, simultaneously press
and hold the position 1 and off buttons
(FIGURE 14). The transmission indicator
light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
STEP 3
Repeat Step 1 and Step 2 with hand control 2.
STEP 4
Locate the power down box for bed 2 and
press the learn button for 1 second and
release (FIGURE 13).
STEP 6
Repeat Step 4 and Step 5 with hand
control 2.
Two hand controls are now programmed
to operate two beds.
STEP 5
On hand control 1, simultaneously press
and hold the position 1 and the off buttons
(FIGURE 14). The transmission indicator
light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
NOTE
POWER
DOWN BOX
LEARN
BUTTON
FIGURE 13: Power down box learn button.
FIGURE 14
OFF
BUTTON
TRANSMISSION
INDICATOR
LIGHT
POSITION 1
BUTTON
HAND
CONTROL 1
BED 1
HAND
CONTROL 2
BED 2

Tempur-Pedic
®
Owners Manual
9
10. Install mattress retainer as follows:
a. Locate (1) mattress retainer and (1)
mattress retainer hardware kit (bag).
b. Install (1) cupped washer, (1) spacer
and (1) flat washer on (4) mattress
retainer bolts (FIGURE 4).
MATTRESS RETAINER HARDWARE
KIT CONTAINS:
(4) MATTRESS RETAINER BOLTS - A
(4) FLAT WASHERS - B
(4) SPACERS - C
(4) CUPPED WASHERS - D
CUPPED
WASHER
FLAT
WASHER
SPACER
MATTRESS
RETAINER
BOLT
assemble as
shown:
A
B
C
D
FIGURE4: Standard mattress retainer hardware.
Note: if adjustable bed is to be set up
without a headboard, basic installation is
now complete. If headboard is to be
installed, proceed to step 11.
DO NOT USE POWER SCREWDRIVER TO
INSTALL MATTRESS RETAINER.
DO NODO NO
DO NODO NO
DO NOTT
TT
T
OO
OO
OVERTIGHTEN MAVERTIGHTEN MA
VERTIGHTEN MAVERTIGHTEN MA
VERTIGHTEN MATTRESS RETTTRESS RET
TTRESS RETTTRESS RET
TTRESS RETAINERAINER
AINERAINER
AINER
HARDHARD
HARDHARD
HARDWW
WW
WARE!ARE!
ARE!ARE!
ARE!
NOTE
FIGURE 6: Standard mattress retainer installed.
c. Install the mattress retainer bolts
(loosely) into the (4) threaded lugs in
the top side of the bed base at the foot
section (FIGURE 5).
d. Slide each U-shaped end of the
mattress retainer around the mattress
retainer bolts. Position the retainer
ends with the cupped washers on top
(FIGURE 5).
INSTALLATION
FLAT WASHERS FIT
BETWEEN THE BED
BASE FRAME AND THE
MATTRESS RETAINER
(2) THREADED LUGS IN
EACH SIDE OF THE
BED FOOT SECTION
STANDARD
MATTRESS
RETAINER
FIGURE 5: Standard mattress retainer installation.
CUPPED
WASHERS
e. Tighten screws to complete mattress
retainer installation (FIGURE 6).
Tempur-Pedic
®
Owners Manual
16
TEMPUR-ERGO PROGRAMMING 1 hand control - 2 beds
STEP 1
Locate the power down box for bed 1 and
press the learn button for 1 second and
release (FIGURE 13).
The three step procedure below is required to program 1 hand control to operate 2 beds.
Before beginning, make certain the beds are plugged into a working grounded electrical
outlet.
STEP 2
On the hand control simultaneously press
and hold the position 1 and off buttons
(FIGURE 14). The transmission indicator
light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
STEP 3
Repeat Step 1 and Step 2 with bed 2.
One hand control is now programmed to
operate two beds.
BED 2
BED 1
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
NOTE
FIGURE 14
OFF
BUTTON
TRANSMISSION
INDICATOR
LIGHT
POSITION 1
BUTTON
POWER
DOWN BOX
LEARN
BUTTON
FIGURE 13: Power down box learn button.

Tempur-Pedic
®
Owners Manual
10
HEADBOARD BRACKET INSTALLATION
When attaching (2) twin size units to a king
size headboard, use a swing hinge kit (see
accessories page) to connect the twin
units.
INSTALLATION
3 inches MAX.
FIGURE 7: headboard cross member location must not
exceed 3 inches (76.2mm) from the top of the mattress.
FAILURE TO FOLLOW HEADBOARD
BRACKET INSTALLATION INSTRUCTIONS
MAY CAUSE HEADBOARD BRACKET
INTERFERENCE WITH BASE FOAM DURING
ADJUSTABLE BED OPERATION. BASE
FOAM OR BASE COVER DAMAGE COULD
RESULT.
NOTE
IN ORDER TO AVOID A PERSON OR PET
BEING CAUGHT IN THE SPACE
REFERENCED BELOW WHILE THE BED IS IN
MOTION, THE BOTTOM OF THE
HEADBOARD CROSS MEMBER MUST BE
POSITIONED SO THAT THERE IS NO MORE
THAN 3 INCHES (76.2mm) BETWEEN THE
HEADBOARD AND THE TOP OF THE
MATTRESS (FIGURE 7).
DO NODO NO
DO NODO NO
DO NOT EXT EX
T EXT EX
T EXCEEDCEED
CEEDCEED
CEED
3 INCHES (76.23 INCHES (76.2
3 INCHES (76.23 INCHES (76.2
3 INCHES (76.2mmmm
mmmm
mm).).
).).
). FAILURE TO FOLLOW
THIS INSTRUCTION COULD RESULT IN
SERIOUS PERSONAL INJURY OR DEATH.
Tempur-Pedic
®
Owners Manual
15
TEMPUR-ERGO PROGRAMMING 2 hand controls - 1 bed
The three step procedure below is required to program 2 hand controls to operate 1 bed.
Before beginning, make certain the bed is plugged into a working grounded electrical
outlet.
STEP 2
On hand control 1, simultaneously press
and hold the position 1 and off buttons
(FIGURE 14). The transmission indicator
light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
STEP 3
Repeat Step 1 and Step 2 with hand
control 2.
Two hand controls are now programmed
to operate one bed.
STEP 1
Locate the power down box for the bed
and press the learn button for 1 second
and release (FIGURE 13).
IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
NOTE
HAND
CONTROL 1
HAND
CONTROL 2
FIGURE 14
OFF
BUTTON
TRANSMISSION
INDICATOR
LIGHT
POSITION 1
BUTTON
LEARN
BUTTON
POWER
DOWN BOX
LEARN
BUTTON
FIGURE 13: Power down box learn button.

Tempur-Pedic
®
Owners Manual
11
FIGURE 8: Headboard bracket hardware.
HEADBOARD BRACKET
HARDWARE KIT CONTAINS:
(4) 3 INCH CARRIAGE BOLTS - A
(4) 1 INCH HEX HEAD BOLTS - B
(8) NUTS - C
C
A
B
INSTALLATION
11. Install headboard brackets to the bed base
frame per the following instructions:
a. Raise the head section of the bed (with
hand control) to gain access to the bed
base frame.
b. Slide one headboard bracket channel
onto one side of the bed base frame.
Using (2) carriage bolts/nuts (FIGURE
8) attach channel to base frame
(FIGURE 9). Hand tighten bolts/nuts
(loosely) to allow adjustment of the
headboard bracket channels. Repeat
procedure to install the other
headboard bracket channel to the
other side.
QUEEN SIZE HEADBOARD BRACKET
ASSEMBLIES ARE SHOWN. TWIN SIZE
HEADBOARD BRACKETS (OR SMALLER)
ARE NOT EQUIPPED WITH ANGLE BRACE
(FIGURES 9 and 10).
NOTE
FIGURE 9: Headboard bracket channel installation (one each
side of the head section of the bed).
SLIDE HEADBOARD
BRACKET CHANNEL OVER
THE BED BASE FRAME
EXTENSION
USE (2) 3 INCH CARRIAGE BOLTS AND
NUTS TO ATTACH EACH BRACKET
CHANNEL TO BED BASE FRAME
EXTENSION
ANGLE
BRACE
c. Attach one headboard bracket flange
to one of the bracket channels with (2)
hex head bolts/nuts. (FIGURE 10)
Tighten bolts. Repeat procedure to
attach the other headboard bracket
flange.
FIGURE 10: Headboard bracket flange installation (attach one
flange to each of the headboard bracket channels).
USE (2) 1 INCH HEX HEAD
BOLTS AND NUTS (TIGHTEN)
TO ATTACH HEADBOARD
BRACKET FLANGE TO EACH
BRACKET CHANNEL
ANGLE
BRACE
Tempur-Pedic
®
Owners Manual
14
STEP 1
Locate the receiver unit (power down box)
for the bed and press the learn button for
1 second and release (FIGURE 13).
The two step procedure below is required to program 1 hand control to operate 1 bed.
Before beginning, make certain the bed is plugged into a working grounded electrical
outlet.
STEP 2
On the hand control, simultaneously press
and hold the position 1 and off buttons
(FIGURE 14). The transmission indicator
light will flash slowly and then flash
rapidly. Continue to hold for 5 seconds and
then release the buttons.
One hand control is now programmed to
operate one bed. IF PROGRAMMING FAILS, INITIATE THE
PROGRAMMING PROCEDURE A SECOND
TIME.
NOTE
TEMPUR-ERGO PROGRAMMING 1 hand control - 1 bed
FIGURE 14
OFF
BUTTON
TRANSMISSION
INDICATOR
LIGHT
POSITION 1
BUTTON
POWER
DOWN BOX
LEARN
BUTTON
FIGURE 13: Power down box learn button.

Tempur-Pedic
®
Owners Manual
12
d. Slide headboard bracket assemblies (in
or out) to achieve a distance of 1.5
inches (38.1mm) to 2 inches (50.8mm)
between the edge of the bed base and
headboard bracket flange assemblies
(FIGURE 11).
e. Firmly tighten the 3 inch carriage bolts
of both headboard bracket channels.
f. Measure the distance (center-to-
center) between the mounting holes in
the headboard.
g. Measure the center-to-center distance
between the mounting slots of the
headboard bracket flanges (FIGURE 12).
h. If bracket flange adjustment is required
to accept the headboard, remove the 1
inch headboard bracket flange bolts
and move flanges
side-to-side for
the adjustment
(FIGURE 12).
Reinstall bolts
and tighten.
i. Install headboard.
12. Install mattress on
the adjustable bed
base.
Typical Tempur-Pedic®
adjustable bed
installation is now
complete.
INSTALLATION
FIGURE 11: Headboard bracket position from the edge of the
bed base frame.
1.5 to 2 inches
SLIDE BRACKET
ASSEMBLIES IN OR
OUT TO ACHIEVE
POSITION
FIGURE 12: Headboard bracket measurement and adjustment to accept headboard.
MEASURE FLANGE SLOTS
CENTER-TO-CENTER TO CHECK
HEADBOARD HOLE LOCATION
REMOVE 1 INCH BOLTS AND RELOCATE
FLANGES TO ACHIEVE CENTER-TO-CENTER
DISTANCE REQUIRED FOR HEADBOARD
MOUNTING HOLES
Tempur-Pedic
®
Owners Manual
13
TEMPUR-ERGO HAND CONTROL
HAND CONTROL REQUIRES FOUR (4) AAA SIZE BATTERIES. TO CONSERVE
BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY
BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.
NOTE
TRANSMISSION INDICATOR
LIGHT
Verifies a button is being pressed
and data is being sent to the bed. FOOT BUTTON
Press to select the foot section of
the bed for adjustment. Then raise
or lower the foot section by
pressing the up/down button.
CUSTOM BUTTON
Press to return the bed to the
custom programmed position.
UP/DOWN BUTTONS
After selecting any position or
function, adjust the position or
intensity by pressing the up/down
buttons.
MASSAGE OFF BUTTON
Press and hold to turn off last
selected massage function.
FOOT MASSAGE BUTTON
Press to activate the foot massage.
Adjust the massage intensity by
pressing the up/down buttons.
WAVE MASSAGE BUTTON
After activating the head and/or
foot massage motors, press and
hold the wave massage button to
the activate the wave feature.
Adjust the wave speed by
pressing the up/down buttons.
HEAD MASSAGE BUTTON
Press to activate the head
massage. Adjust the massage
intensity by pressing the up/down
buttons.
FLAT BUTTON
Press and release to return the bed
to the flat position. This button will
also turn off the massagers.
HEAD BUTTON
Press to select the head section of
the bed for adjustment. Then raise
or lower the head section by
pressing the up/down button.
SET BUTTON
Press to capture any position or
function (massage or wave) of the
bed as a programmed position.
Press the custom button to return
the bed to the custom
programmed position.
POSITION BUTTONS
The adjustable bed is equipped
with 3 factory preset positions.
Press and release a button and the
bed will automatically move to the
preset position. To stop the bed
while in motion, press and hold
any button until the bed stops.