Tempur-Pedic TEMPUR-ERGO PLUS User manual

CUSTOMER SERVICE: 1–800–821–6621
Adjusting Your
TEMPUR-Ergo™Plus
Adjustable Base
To adjust the Head section, press the HEAD UP
button (1) or HEAD DOWN button (2). Keep pressing
the respective button until the desired height is
reached.
To adjust the Leg section, press the LEG UP button
(3) or LEG DOWN button (4). Keep pressing the
respective button until the desired height is reached.
Press and hold the FLAT button (5) for 3 seconds,
and the bed frame will automatically move into its
complete at position.
56
CUSTOMER SERVICE: 1–800–821–6621
Change From a
Single System to a
Tandem System
This function will pair the remotes from two
adjustable bases, allowing each remote to control
both bases in unison.
Pair Remote 1 to Base 2 by pressing and holding the
Learn Button on the Control Box. It will blink three (3)
times when ready.
Press the Learn Button two (2) times. This will select
the second remote channel. The LED will turn off.
Press any button on the new remote. The LED on
the Control Box will blink two (2) times and return on
once programmed.
Pair Remote 2 to Base 1 by repeating the process
above.
Patents Pending Rev 101013
Quick Start
Guide
TEMPUR-Ergo™Plus
Adjustable Base
CUSTOMER SERVICE: 1–800–821–6621
© 2013 Tempur-Pedic Management, LLC. All rights reserved.
NOTE: Ensure all obstructions are clear of the
adjustable base’s undercarriage when lifting
or lowering the base’s head and leg sections
to avoid risk of pinching or damage.
NOTE: Each remote must be programmed to
the opposite control box.
1. HEAD UP (HU)
3. LEG UP (LU)
6. MEMORY PRESET 1
2. HEAD DOWN (HD)
7. MEMORY PRESET 2
5. FLAT (F)
4. LEG DOWN (LD)

CUSTOMER SERVICE: 1–800–821–6621
Setting Up Your
TEMPUR-Ergo™ Plus
Adjustable Base
Use this quick start guide to set up
and operate your TEMPUR-Ergo™Plus
Adjustable Base right away. Refer to the
User Guide for more detailed information.
Decide where you want your new TEMPUR-Ergo
Plus Adjustable Base. Make sure there is an
electrical outlet nearby.
Carefully lift the TEMPUR-Ergo Plus Adjustable Base
out of the shipping carton, keeping the unit topside
down. For safety reasons, this should be performed
by two people.
Remove the remote control and (2) AA batteries
from the accessory pack, remove the cover from the
remote control’s battery compartment, and install the
(2) AA batteries into the remote.
Install (2) 9-Volt batteries into the battery
compartment of the power supply.
2 3 4
CUSTOMER SERVICE: 1–800–821–6621 CUSTOMER SERVICE: 1–800–821–6621
NOTE: To avoid damage
to the base, always open
the carton while the bed
is in the flat position.
Attach TEMPUR-Ergo Plus Legs: Open the
accessories box, take out the (4) legs, and thread
them in a clockwise direction into the pre-threaded
holes in the frame.
NOTE: Hand tighten the legs securely to the
frame. DO NOT over tighten. Make sure the
legs are screwed completely into the frame.
Legs that are not securely attached may
become unsafe. DO NOT unscrew a leg to
compensate for an uneven floor.
NOTE: Locking casters are available for
aftermarket purchase. In order to prevent the
movement of this product, all four casters
should be in the locked position.
Carefully ip the TEMPUR-Ergo Plus Adjustable
Base over to the topside up position.
NOTE: Make sure to lift the base off the
ground before flipping over. DO NOT use legs
as a leverage point to ensure that they do
not break.
Route the control box cable to your preferred side
of the bed.
Connect the power cord from the power supply to
the surge protector (not included).
Proper handling
!
Turn bed over without leaning against the
installed legs.
DO NOT
lean the bed against the
installed legs to flip it over.
ATTENTION ! Improper handling
!
Installing the
Mattress
Retainer Bar
Remove Mattress Retainer Bar and Retainer Bar
Plates from frame. Install in upright position.
Line up the Retainer Bar Plate over the Mattress
Retainer Bar so the threaded holes are lined up.
Start with the right side and insert two (2) Retainer
Bar Bolts through the holes of the Retainer Bar
Plate through the opening in the Mattress Retainer
Bar to the base. Do not over tighten.
Place the mattress on the base.
Ensure the power switch on the surge protector is
in the “on” position and that it is plugged into the
wall outlet. Check the system for functionality with
the mattress in place.