Tempur-Pedic Split CA King User manual

COMPLETE REFERENCE GUIDE
®
© 2009 Tempur-Pedic Management, Inc. 1713 Jaggie Fox Way, Lexington, KY 40511. All Rights Reserved.
U.S. Patent No. 7,321,811 and other patents pending
TPNA-CRG-TAES-0509

®
2 3
SERIAL NUMBER:
Table of Contents
SAFETY PRECAUTIONS .............................................................................................. 4
COMMONLY ASKED QUESTIONSAND ANSWERS .................................................... 8
SPECIFICATIONS......................................................................................................... 9
INSTALLATION ......................................................................................................... 10
OPERATION
WIRELESS REMOTE CONTROL PROGRAMMING ............................................... 15
WIRELESS REMOTE CONTROL FEATURES ......................................................... 16
OPERATING INSTRUCTIONS .............................................................................. 17
TROUBLESHOOTING................................................................................................ 18
®
20-YEAR LIMITED WARRANTY
TEMPUR-PEDIC NORTH AMERICA, INC. (“TEMPUR-PEDIC”) GUARANTEES THAT WE WILL, AT TEMPUR-PEDIC’S OPTION,
REPLACE OR REPAIR PURCHASER’S TEMPUR ADVANCED ERGO SYSTEM™IF IT IS DEFECTIVE DUE TO FAULTY WORKMANSHIP OR
MATERIALS, SUBJECT TO THE LIMITATIONS DESCRIBED IN THIS WARRANTY.
YEAR 1 - FULL COVERAGE OF PARTS AND LABOR
Your TEMPUR®Advanced Ergo System™is warranted against defects in the workmanship or materials for a period of one (1) year from the warranty
commencement date. Electronics, electrical components, drive motors and massage motors are included. Upon notice during the first year from the
warranty commencement date, Tempur-Pedic will send replacement parts (at no cost to the purchaser) for any defective part to the purchaser, and
Tempur-Pedic will pay all authorized labor and transportation costs associated with the repair or replacement of any parts Tempur-Pedic determines
to be defective. This one (1) year warranty shall not apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15 days of
purchaser’s receipt of replacement part.
YEARS 2 AND 3 – FULL COVERAGE OF PARTS ONLY
Upon notice during the years two and three (2 - 3) from the warranty commencement date, Tempur-Pedic will offer replacement parts for any
defective part to the purchaser. Electronics, electrical components, drive motors and massage motors are included. This two (2) year warranty shall not
apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15 days of purchaser’s receipt of replacement part. Purchaser shall
bear all service, transportation, labor, and shipping costs related to the delivery and/or replacement of the defective part.
YEARS 4 THROUGH 20 – PRORATED COVERAGE OF PARTS ONLY
Upon notice during the fourth through the twentieth (4 – 20) years from the warranty commencement date, Tempur-Pedic will offer replacement
parts (upon terms and conditions set forth in this paragraph) for any mechanical bed part found to be defective. Electronics, electrical components,
drive motors and massage motors are excluded. Purchaser shall pay 1/17th of the then current replacement cost of the defective part multiplied
by the number of years after three (3) years from the warranty commencement date, and Tempur-Pedic shall bear the remainder of the cost of the
replacement part. This seventeen (17) year warranty shall not apply if purchaser does not return any and all defective parts to Tempur-Pedic within 15
days of purchaser’s receipt of replacement part. Purchaser shall bear all service, transportation, labor, and shipping costs related to the delivery and/
or replacement of the defective part. After the 20th year, purchaser shall bear the entire cost of repair and replacement of all parts and materials,
including labor and transportation.
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any damage caused by the purchaser; (b) if there has been any unauthorized repair or replacement of the unit’s
parts; (c) if the unit has been mishandled (whether in transit or by other means), subjected to physical or electrical abuse or misuse, or otherwise
operated in any way inconsistent with the operation and maintenance procedures outlined in the Complete Reference Guide, this warranty, and any
other applicable document published or approved by Tempur-Pedic; (d) to damage to mattresses, fabric, cables, electrical cords or items supplied by
Resellers. Contact the Reseller or relevant party for warranty information on these items.; (e) if there has been any unnecessary service calls, including
costs for in-home service calls solely for the purpose of educating the consumer about the unit for finding an unsatisfactory power connection; (g) if
the recommended weight restrictions are not followed (Twin, Twin Long, Split/Dual Queen, Split/Dual CA King – 300 lbs.; Double, Double Long – 375
lbs.; Queen – 425 lbs.), the warranty will be void.
Repairs to or replacement of the TEMPUR Advanced Ergo System or its components under the terms of this limited warranty will apply to the original
warranty period and will not serve to extend such period.
The decision to repair or to replace defective parts under this warranty shall be made, or case to be made, by Tempur-Pedic at its option and in its sole
discretion.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE PURCHASER. THERE SHALL BE NO LIABILITY ON THE PART OF TEMPUR-PEDIC
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR FOR ANY OTHER DAMAGE, CLAIM, OR LOSS NOT EXPRESSLY
COVERED BY THE TERMS OF THIS WARRANTY. THIS LIMITED WARRANTY DOES NOT INCLUDE REIMBURSEMENT FOR INCONVENIENCE, REMOVAL,
INSTALLATION, SETUP TIME, LOSS OF USE, SHIPPING, OR ANY OTHER COSTS OR EXPENSES. TEMPUR-PEDIC MAKES NO OTHER WARRANTY
WHATSOEVER, EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED BY TEMPUR-PEDIC AND EXCLUDED FROM THIS AGREEMENT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
every purchaser. This warranty gives the purchaser specific legal rights, and the purchaser may also have other rights, which may vary from state to
state. This warranty is valid in all 50 states, Puerto Rico, and Canada. This warranty is valid only for the original purchaser of the product. An original
purchaser is one who purchases the product directly from Tempur-Pedic North America, Inc. or an authorized Reseller of Tempur-Pedic North America,
Inc. If you are not the original purchaser of this product, you take it “as is” and “with all faults.” If you did not purchase this TEMPUR Advanced Ergo
System directly from Tempur-Pedic North America, Inc., we will require proof of purchase from you demonstrating that you are the original purchaser
and eligible to make a valid claim under this warranty. This warranty begins on the “warranty commencement date” which is the date of purchase for
new unused units, and the date of manufacture for units that have been used as floor or display models. Thus, on a floor model unit, the warranty is a
portion of the limited 20-year warranty. If original proof of purchase is not provided by purchaser, Tempur-Pedic reserves the right to determine if the
unit is not covered by this warranty or to use the manufacturing date as the warranty commencement date. This limited warranty gives you specific
legal rights. You may also have other rights that vary from state to state.
If you experience any trouble with your TEMPUR Advanced Ergo System during the warranty period, please consult the troubleshooting section of your
Reference Guide. If problems persist after following these instructions, please call: 1-800-979-1457
PLEASE RETAIN THIS WARRANTY AND YOUR ORIGINAL PROOF OF PURCHASE FOR AT LEAST 20 YEARS FROM THE DATE OF PURCHASE.
2
Customer Service: 1–800–979–1457

®
Safety Precautions
SAFETY PRECAUTIONS
WARNING!
IMPORTANT SAFETY
INSTRUCTIONS.
PLEASE
READ THESE
INSTRUCTIONS
THOROUGHLY BEFORE
USING THIS PRODUCT.
SAVE THESE INSTRUCTIONS!
Your TEMPUR®Advanced Ergo System™has been
designed to provide you with the reliable operation and
durability you expect. This product has been inspected and
tested prior to shipment.
When using an electrical furnishing, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR
TEMPUR®ADVANCED ERGO SYSTEM™
DANGER:
To reduce the risk of electric shock
Always unplug this furnishing from the electrical outletUÊ
before cleaning.
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons:
Unplug from outlet before putting on or taking off parts.UÊ
Close supervision is necessary when this furnishing isUÊ
used by, or near children, invalids, or disabled persons.
Use this furnishing only for its intended use as describedUÊ
in these instructions. Do not use attachments not
recommended by the manufacturer.
Never operate this furnishing if it has a damaged cordUÊ
or plug, if it is not working properly, if it has been
dropped or damage, or dropped into the water. Return
the furnishing to a service center for examination and repair.
Keep the cord away from heated surfaces.UÊ
Never operate the furnishing with the air openings blocked.UÊ
Keep the air openings free of lint, hair and the like.
Never drop or insert any object into any opening.UÊ
Do not use outdoors.UÊ
Do not operate where aerosol (spray) products areUÊ
being used or where oxygen is being administered.
To disconnect, turn all controls to the off position, thenUÊ
remove plug from outlet.
WARNING:
Risk of Injury — Keep children away from extended
foot support (or other similar parts).
WARNING!
Risk of electric shock — Connect this furnishing to a
properly grounded outlet only. See Grounding instructions.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction
or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric
shock. This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that
is properly installed and grounded in accordance with all
local codes and ordinances.
DANGER
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with
a qualified electrician or serviceman if you are In doubt
as to whether the product is properly grounded. Do not
modify the plug provided with the product — if it will not
fit the outlet, have a proper outlet installed by a qualified
electrician.
SAVE THESE INSTRUCTIONS!
GROUNDING SAFETY
This product is for use on a nominal 120-volt circuit, and
has a grounding plug that looks like the plug illustrated
in sketch A (see Figure). A temporary adapter that looks
like the adapter illustrated in sketches B and C able to
be used to connect this plug to a 2-pole receptacle as
shown in sketch B if a properly grounded outlet is not
available. The temporary adapter should be used only until
a properly grounded outlet (sketch A) can be installed by
a qualified electrician. The green colored rigid ear, lug, or
the like extending from the adapter must be connected to
a permanent ground such as a properly grounded outlet
box cover. Whenever the adapter is used, it must be held
in place by a metal screw.
This product is for use on a circuit having a nominal
rating more than 120 volts and is factory equipped with
a specific electric cord and plug to permit connection to
a proper electric circuit. Make sure that the product is
connected to an outlet having the same configuration as
the plug. No adapter should be used with this product. If
the product must be reconnected for use on a different
type of electric circuit, the reconnection should be made
by qualified service personnel.
Unauthorized modifications could void the electrical
portion of your warranty. Failure to use a properly
grounded outlet for this product or modification of the
plug will compromise this important grounding safety
feature and may result in electrical shock, electrical fire, or
faulty operation of the product.
FOR BEST RESULTS, YOUR ERGO SYSTEM SHOULD BE
PLUGGED INTO A SURGE PROTECTOR (not included).
WARRANTY PRECAUTION!
Do not open control box, motors or wireless remote
control (with the exception of the battery compartments).
The warranty is void if these units are tampered with.
Any repair or replacement of Ergo System parts must be
performed by an authorized person.
IN-HOME USE AND HOSPITAL DISCLAIMER
Your Ergo System is strictly designed for in-home use
only. It is NOT designed for hospital use and is NOT
designed to meet hospital standards. DO NOT USE this
bed with TENT TYPE oxygen therapy equipment or near
explosive gases.
WARNING:
DO NOT USE NEAR PEOPLE USING OR WEARING
MEDICAL DEVICES. FOR HOUSEHOLD / RESIDENTIAL USE
ONLY. DO NOT USE OUTDOORS.
This product conforms to UL STD 962
4
Customer Service: 1–800–979–1457
5
Customer Service: 1–800–979–1457

®
Safety Precautions
IMPORTANT SAFETY FEATURES
Use this furnishing only for its intended use as described
in these instructions. Do not use attachments not
recommended by the manufacturer.
If there is an overload weight condition on the head
or foot mechanism, the control unit will automatically
stop all functions. Once the excess weight is removed,
the control unit will automatically allow all functions to
resume operation after 30 seconds.
For your safety, this Ergo System is equipped with special
locking casters. In order to prevent the movement of this
product, all six casters should be in the locked position.
This can be accomplished by pushing down the locking
latch on the caster. To resume mobility of the product, lift
the locking latch up. You are strongly encouraged to place
rubber caster cups or carpet squares under the casters
in addition to locking them in place if the product is
positioned on a hard surface floor such as hardwood, tile
or linoleum. Although the casters are locked and will not
roll, they may slide.
CONSUMERS WITH PACEMAKERS
As with any product that produces a vibrating motion
(optional), it is possible that some pacemakers may
interpret this motion as a false sense of movement
and/or exercise. This may or may not affect your pacemaker.
If you have any concerns, please consult your physician.
For information on disabling the vibrating motors, please
contact customer service by calling 1-800-979-1457.
USER-SERVICEABLE PARTS
This product is specifically designed to have no
maintenance by you, the user. Therefore, you are
encouraged not to open any motors, alter the wiring, or
adjust, modify or change the structure of the product, as
it will void the warranty.
POWER RATINGS:
MODEL NO: SY-66D
INPUT: AC 100V/110V- 50/60HZ, 1AMP
OUTPUT: DC 24V-3A
FUSE: 1A250V(MAX 1.5A)
The input transformer voltage is AC120V (1 Amp) 60HZ,
and the output voltage is DC24V (3 Amp). When there is
a short-circuit, a fuse on the transformer will be blown in
order to protect the electrical equipment (Fuse: 1A~1.5A.).
Should the above situation occur, the customer should
seek professional assistance by calling a licensed electrician
or by contacting customer service at 1-800-979-1457.
SMALL CHILDREN AND
PETS WARNING
After your Ergo System has been unboxed, immediately
dispose of packaging as it can smother small children
and pets. To avoid injury, children and pets should not
be allowed to play on or under the bed. Children should
not operate this product without adult supervision. Close
supervision is necessary when this furnishing is used by, or
near children, invalids, or disabled persons.
SAVE THESE INSTRUCTIONS!
Your Ergo System has been designed to provide
you with the reliable operation and durability you
expect. This product has been inspected and tested
prior to shipment.
RADIO FREQUENCY IS 433.92 MHZ.
FCC COMPLIANCE
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
To comply with the FCC RF exposure compliance
requirements, no change to the antenna or
the device is permitted. Any change to the
antenna or the device could result in the device
exceeding the RF exposure requirements and
void user’s authority to operate the device.
PRODUCT RATINGS
The lift motors in your Ergo System are NOT designed for
continuous use. Reliable operation and full life expectancy
will be attained as long as the lift motors do not operate
more than two (2) minutes over a eighteen (18) minute
period, or approximately 10% duty cycle. Any attempt
to circumvent or exceed this rating will shorten the life
expectancy of this product and may void the warranty. The
recommended weight restrictions on our Ergo Systems
are as follows: Twin, Twin Long, Split/Dual Queen, Split/
Dual CA King – 300 lbs.; Double, Double Long – 375 lbs.;
Queen – 425 lbs. This Ergo System will structurally support
the recommended weight distributed evenly across the
head and foot sections. This product is not designed to
support or lift this amount of weight in the head or foot
sections alone.
NOTE: Exceeding the recommended weight
restrictions could damage your Ergo System and
void your warranty.
For best performance, you should enter and exit the Ergo
System while it is in the flat or fully lowered position.
INTENDED USAGE
The electric adjustable bed should be installed with
the head board bracket and/or the head of the
frame should be positioned close to a wall.
6
Customer Service: 1–800–979–1457
7
Customer Service: 1–800–979–1457

®
Commonly asked Questions and Answers
Q&A / Specifications
Measurements are approximate and based on standard leg with caster.
D
D
DD
D
D
E
F
D
E
EE
EE
F
FF
FF
EE
F
F
No Leg
(rest on frame)
D) To Frame 0” 2 1/2” 4 1/8” 6 5/8” 6 1/8” 8 3/4” 7 1/2” 10 1/2”
E) To Base 1” 3 1/2” 5 1/8” 7 5/8” 7 1/8” 9 3/4” 8 1/2” 11 1/2”
F) To Mattress 8 3/4” 11 1/4” 12 7/8” 15 3/8” 14 7/8” 17 1/2” 16 1/4” 19 1/4”
Caster Only Standard Leg
(without caster)
Standard Leg
(with caster)
8” Riser Leg
(without caster)
10” Riser Leg
(without caster)
8” Riser Leg
(with caster)
10” Riser Leg
(with caster)
C
B
15 3/8”
7 3/4”
54 3/8”
27 3/16”
27 3/16”
39 3/8”
21 1/4”
69˚
61”
A
6 5/8”
39˚
Bed Type A. Frame
width
B. Base
Width
C. Base
Length
Weight
Twin 33 1/2” 37 1/2” 74 1/4” 168 lbs.
Twin Long 33 1/2” 37 1/2” 79” 172 lbs.
Double 48 3/4” 53 1/4” 75” 218 lbs.
Double Long 48 3/4” 53 1/4” 79” 224 lbs.
Queen 48 3/4” 58 1/4” 79” 234 lbs.
Split Queen 26 1/4” 29 1/2” 79” 136 lbs.
Split CA King 33 1/2” 35 3/4” 82 3/4” 159 lbs.
Specifications
WHAT IS THE HEIGHT OF THE ERGO SYSTEM BASE?
With standard legs and casters installed, the overall
height is approximately 15 3/4” floor to the bottom
of the mattress. The distance between the floor and
the bottom edge of the base, with standard legs and
casters installed, is approximately 7 5/8”. See chart on
page 9 for other options.
WHY CAN’T IREADJUST THE ERGO SYSTEM BASE
IMMEDIATELY AFTER I USE THE FLAT BUTTON TO
RETURN IT TO THE FLAT POSITION?
All functions are temporarily disabled for approximately
20 seconds to allow the Ergo System base to complete
the “FLAT” cycle and reset. The “FLAT” cycle can be
interrupted at any time by selecting the “HEAD” or
“FOOT” up or down keys.
IS IT POSSIBLE TO RAISE THE HEIGHT OF THE
ERGO SYSTEM BASE?
Yes, you can add up to 4” to the overall height of the
Ergo System by ordering the riser leg set. These include 6
replacement legs with casters, and come with either an
overall height of approximately 8” or 10”. Please note
that the riser leg set replaces the standard leg set that
comes with the Ergo System. They are not used together.
DOESTHE ERGO SYSTEM BASE COME WITH
FOOTBOARD ATTACHMENTS?
No, you cannot attach a footboard directly to the Ergo
System base. However, you can use a “freestanding”
bed including headboard, footboard and side rails
by placing the complete Ergo System within the
assembled bed. It may be easiest to assemble the bed
around the Ergo System. You should measure the
inside dimensions of the assembled bed to be sure the
Ergo System will fit. One of our riser leg sets may be
required in some cases.
WILL THE ERGO SYSTEM FIT INSIDE EXISTING
FURNITURE?
The Ergo System is designed to fit into most
“freestanding” beds. We always recommend you
measure the inside dimensions of the assembled bed
to be sure the Ergo System will fit. Please refer to the
specifications on page 9 for exact dimensions of the base.
One of our riser leg sets may be required in some cases.
WHERE ISTHE SERIAL NUMBER ON THE ERGO
SYSTEM BASE?
The serial number can be found on the law tag
attached to the cover, the power down box under the
base and on the frame right below the foot end of the
base. It may be easier to see by lifting the foot slightly
if possible. The serial number is also located on the
Complete Reference Guide (owner’s manual) shipped
with the base.
WHAT IS THE LIFT CAPACITY OF THE ERGO SYSTEM?
Please see the chart below for Tempur-Pedic’s
recommended and approved “total people weight” limits
per the available mattress and Ergo Base combinations.
Total People Weight
Product Single Base Dual Bases
OriginalBed ≤500 lbs. 500 lbs. - 1000 lbs.
AdvantageBed ≤500 lbs. 500 lbs. - 1000 lbs.
ClassicBed ≤500 lbs. 500 lbs. - 1000 lbs.
DeluxeBed ≤500 lbs. 500 lbs. - 1000 lbs.
BellaFina Bed ≤500 lbs. 500 lbs. - 1000 lbs.
RhapsodyBed ≤500 lbs. 500 lbs. - 1000 lbs.
CelebrityBed ≤400 lbs. 400 lbs. - 800 lbs.
AlluraBed ≤400 lbs. 400 lbs. - 800 lbs.
BellaSonna Bed Not Available Not Available
GrandBed Not Available Not Available
WHO DO ICALL FOR SERVICE OR SUPPORT IF NEEDED?
Service and technical support is available by calling
our dedicated customer service group at 1-800-979-
1457. An owner’s manual is included with each base
including other information for making claims.
IS AN EXTENDED WARRANTY AVAILABLE?
No.
DO I GET A FULL WARRANTY IF I PURCHASE A
FLOOR MODEL?
Yes. However, your warranty start date is the date of
manufacture which is clearly marked on the law tag
attached to the base (not your actual purchase date).
WHAT ARE THE ELECTRICAL REQUIREMENTS OF
THE ERGO SYSTEM BASE?
During normal operation, the base will typically draw
1.0 Amp of electricity from a normal AC wall outlet.
The power supply has a 1.5 Amp fuse installed to
prevent damage to the unit should a power surge
occur. It is highly recommended that the customer use
a power surge protector (not included with the base).
DOES THE UNIT HAVE AC OR DC MOTORS?
The lift motors used on the Ergo System base are DC
motors. The base’s power supply converts the AC
power from the wall outlet to DC power.
8
Customer Service: 1–800–979–1457
9
Customer Service: 1–800–979–1457

A.
B.*
E.
H.*
K.
C.
F.*
I.
L.
D.
G.
J.
M.
®
Installation
Before discarding any packing materials, check your
TEMPUR®Advanced Ergo System™carton and verify the
following items in the parts list are included:
PARTS LIST
A. Wireless Remote Control (1) and
Four (4) AAA Batteries
B. Mattress Retainer Bar (1)*
C. Bed Leg with Caster (6)
D. Inner Headboard Bracket (2)
E. Outer Headboard Bracket (2)
F. Retainer Bar Bolt (4)*
G. Bracket Bolt (6)
H. Retainer Bar Plate (2)*
I. 5/16 Inch Washer (12)
J. 5/16 Inch Locking Nut (6)
K. Allen Wrench (1)
L. Wrench (1)
M. 9-Volt Batteries (2)
*Attached to base for shipping
Installation Instructions STEP 1
Carefully lift your Ergo System out of the shipping
carton, keeping the unit top side down. For safety
reasons, this should be performed by 2 people.
STEP 2
Attach Ergo System Legs:
Open the accessories box, take out the 6 legs, and
thread them in a clockwise direction into the
pre-threaded holes in the frame.
NOTE: Hand tighten the legs securely to the
frame. Do NOT over tighten. Make sure the legs
are screwed completely into the frame. Legs that
are not securely attached may become unsafe.
DO NOT unscrew a leg to compensate for an
uneven floor.
NOTE: Your Ergo System is equipped with
special locking casters. In order to prevent the
movement of this product, all six casters should
be in the locked position. You are strongly
encouraged to place rubber caster cups or
carpet squares (not provided)
under the casters in addition
to locking them in place.
Although the casters lock and
will not roll, they may slide.
STEP 3
Remove and extend the power cord from the frame.
WARNING! POWER CORDS MUST NOT INTERFERE
WITH ANY ERGO SYSTEM MECHANISMS.
STEP 4
Remove and extend Power Down Box from frame.
Install 9-Volt Batteries.
STEP 5
Carefully flip the Ergo System over to the “topside
up” position and remove the plastic packaging from
the product.
10
Customer Service: 1–800–979–1457
11
Customer Service: 1–800–979–1457

®
Installation
remove the Retainer Bar Plates (H) and Mattress
Retainer Bar. Keep all parts for final installation.
STEP 10
Install the Mattress Retainer Bar (B):
Using the Retainer Bar Bolts (F), Retainer Bar Plates
(H) and the Allen Wrench (K), fasten the Mattress
Retainer Bar upright to the foot of the Ergo System
frame.
NOTE: Use ONLY a manual Allen Wrench to
install the Retainer Bar Bolts. DO NOT use a
power tool to tighten the bolts. DO NOT over
tighten the mattress retainer hardware!
NOTE: If the Ergo System is to be set up without
a headboard, simply place your Tempur-Pedic
mattress onto the frame. Installation is now
complete. If a headboard is to be installed,
proceed to the next page.
NOTE: If the Ergo System is to be used with a
complete headboard, footboard and side rail
combination, assemble the furniture around the
Ergo System base. DO NOT attach the furniture
to the Ergo System base. DO NOT use slats.
STEP 6
Plug the power cord into a grounded electrical outlet.
NOTE: An electrical surge protection unit is
recommended (not included).
STEP 7
Install the batteries in your wireless remote control
(if not already installed). Briefly activate all functions
on the wireless remote control to verify that all of the
features are operational. If your Ergo System does
NOT operate, please refer to the Troubleshooting
section beginning on page 14 of this manual.
STEP 8
Return your Ergo System to the flat position by
pressing and holding the Flat button until the red LED
Signature Light illuminates and the Ergo System base
begins to move.
STEP 9
Detach the Mattress Retainer Bar (B):
For shipping purposes the Mattress Retainer Bar
comes installed upside down. Using the Allen
Wrench (K) loosen the Retainer Bar Bolts (F) and
NOTE: This step is only needed if using a headboard
ONLY. Not headboard, footboard and side rails.
NOTE: Failure to follow the proper headboard
bracket installation instructions may result in
damage to your Ergo System.
WARNING: The bottom of the headboard cross member
must be positioned so that there is no more than 3
inches between the bottom of the headboard and the
top of the mattress. Failure to follow this instruction
could result in serious injury or death to a person or
pet caught between the mattress and the headboard.
STEP 1
Assemble the Headboard Bracket:
STEP 1A
Use the wireless remote to raise the head of the bed
in order to gain access to the Ergo System frame.
STEP 1B
Place the Inner Headboard Bracket (D) into the
C-channel frame, making sure the bracket opening and
the C-channel opening are facing each other. This will
create a box shape. This step does not require you to
loosen or remove any bolts on the delivered bed frame.
Place the Bracket Bolt (G) with a 5/16 inch washer (I)
through the predrilled hole in the C-channel frame
and pass it through the Inner Headboard Bracket.
Adding the 5/16 inch washer (I) and 5/16 inch nut (J),
hand tighten the bolt in place using the supplied
wrenches (K and L).
Repeat for the other side of the frame.
STEP 1C
Place the open side of the Outer Headboard Bracket
(E) onto the exposed square tube of the Inner
Headboard Bracket (D). This will create a tight fit
between (D) and (E).
HEADBOARD INSTALLATION
12
Customer Service: 1–800–979–1457
13
Customer Service: 1–800–979–1457

®
Operation
Place Bracket Bolts (G) with a 5/16 inch washer (I)
through the Outer Headboard Bracket (E) and into
the Inner Headboard Bracket (D). Use 5/16 inch
washers (I) and 5/16 inch nuts (J) and hand tighten to
allow for adjustment.
Repeat on the other side.
STEP 1D
Ensure the Headboard Bracket is assembled with a
distance of 1.5 (38.1 mm) to 2 inches (50.8 mm)
between the edge of the Ergo System and the
headboard bracket assemblies.
STEP 2
Attach your headboard to the Headboard Brackets
following the steps below:
STEP 2A
Measure the center-to-center distance of the
mounting holes in your headboard.
STEP 2B
Measure the center-to-center distance of the
mounting holes in the Headboard Bracket Assemblies.
STEP 2C
If the Headboard Brackets require adjustment, loosen
the bolts that are holding the Outer Headboard
Brackets and move them so that the mounting holes
on the Outer Headboard Bracket align with the
mounting holes on your headboard. Reinstall the
bolts on the Outer Headboard Bracket and firmly
tighten.
STEP 2D
Place your headboard bolts through the mounting
holes on both the Outer Headboard Bracket and your
headboard. Firmly tighten.
STEP 3
Place your Tempur-Pedic mattress on top of your Ergo
System Base.
WARNING: Verify the space between the
headboard cross member and the top of the
mattress is no more than 3 inches.
Your TEMPUR®Advanced Ergo System™installation is now
complete. Refer to the Wireless Remote Control Guide
on the following pages or the supplied Quick Reference
Guide for additional usage instructions.
Wireless Remote Control Programming
ONE WIRELESS REMOTE CONTROL AND ONE ERGO SYSTEM
NOTE: Only replacement wireless remote
controls require user programming. You can
program up to two remotes per base.
STEP 1
Place four AAA batteries into the Wireless Remote
Control.
STEP 2
Ensure the Ergo System base is plugged into a
functioning outlet.
STEP 3
Locate the Emergency Power Down Box under the
Ergo System base and install two (2) new 9-volt
batteries.
STEP 4
Lightly press the learn button for three (3) seconds.
STEP 5
When the Green LED light illuminates, the RF
frequency code setting function will be activated.
Note: The LED light is located on the side of the
plastic housing and is only visible when lit. If a new
signal is not received, it will reset itself to normal
mode in 10 seconds.
STEP 6
Press any button on the wireless remote control. The
Green LED light will blink once it receives a remote
signal. Note: the bed will not respond for 10 seconds
during the remote learn process.
STEP 7
When the Green LED light on the Emergency Power
Down Box turns off, you have completed the learning
process of the RF frequency code.
NOTE: The remote programming procedure
may also be performed using the learn
button on the PLC.
ONE WIRELESS REMOTE CONTROL AND TWO ERGO SYSTEMS
STEP 1
On your first Ergo System, follow the directions for one
(1) wireless remote control and one (1) Ergo System.
STEP 2
Once you have completed the programming of your first
Ergo System, repeat the same directions for the second
Ergo System using the same wireless remote control.
14
Customer Service: 1–800–979–1457
15
Customer Service: 1–800–979–1457

®
Operation
Operating Instructions
HEAD AND FOOT ADJUSTMENTS(A, B)
UÊ `ÕÃÌÃÊÌiÊi>`Ê>`ÊÌÊÃiVÌÃÊÌÊÌiÊ`iÃÀi`Ê
positions. Press until the red LED Signature Light
illuminates and desired position is achieved.
BED “FLAT” BUTTON (C)
UÊ /ÊiÛiÊÌiÊÀ}Ê-ÞÃÌiÊÌÊÌiÊ>ÌÊ«ÃÌ]Ê
press until the red LED Signature Light illuminates.
NOTE: The “FLAT” cycle can be interrupted and
cancelled by pressing the head or foot adjustment
buttons (Aor B). If the “FLAT” command is not
interrupted, all functions are temporarily disabled for
approximately 30 seconds to allow the Ergo System to
reset after the “FLAT” cycle has been completed.
MEMORY BUTTONS(D)
UÊÊ 9ÕÀÊ/*1,®Advanced Ergo System™can store up to
four (4) Memory positions.
UÊ /Ê-iÌÊ>ÊiÀÞÊ*ÃÌ\ÊÊ7iÊÊ`iÃÀi`Ê«ÃÌ]Ê
press and hold Memory button until the LED Signature
Light flashes 3 times to signal Memory position is stored.
UÊ /Ê,iV>Ê>ÊiÀÞÊ*ÃÌ\ÊÊ*ÀiÃÃÊ>`Ê`ÊÌiÊ
corresponding Memory button until the red LED
Signature Light illuminates.* Do not hold for more than
five (5) seconds, otherwise a new Memory position
could be set. If the LED Signature Light begins to flash,
you are reprogramming the Memory position.
HEAD AND FOOT MASSAGE ADJUSTMENTS(E, F)
UÊ /ÕÀÃÊÊÌiÊi>`Ê>`ÊÌÊ>ÃÃ>}iÊÕÌÃÊ
(starting at intensity 5 of 10).
UÊ -ÜÞÊVÀi>ÃiÃÊÀÊ`iVÀi>ÃiÃÊ>ÃÃ>}iÊÌiÃÌÞ°Ê
To increase Massage Intensity, press the (+) button.
To decrease Massage Intensity, press the (-) button.
Wireless Remote Control Features
READ ADVISORY INFORMATION IN THE SAFETY PRECAUTIONSSECTION OF THISGUIDE CAREFULLY BEFORE
USING THIS PRODUCT. THE POTENTIAL FOR ELECTRIC SHOCK EXISTS IF ELECTRICAL COMPONENTS ARE NOT
INSTALLED OR OPERATED PROPERLY.
NOTE: An unintentional touch to any button that does not illuminate the red LED Signature Light on the
wireless remote control will cause the keys to light up without performing the associated function. Press
the appropriate wireless remote control button until the red LED Signature Light illuminates to activate
the desired function. This feature was installed to prevent any undesired movement should the wireless
remote control be dropped, etc.
C. RETURN ALL SECTIONS
TO THE FLAT POSITION
E. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
HEAD SECTION OF THE BASE
G. STOPALL MASSAGE FEATURES
B. RAISE (+) / LOWER (-)
FOOT SECTION OF THE BASE
D. PROGRAM UPTO 4
MEMORY POSITIONS
F. INCREASE (+) / REDUCE (-)
MASSAGE INTENSITY ON
FOOT SECTION OF THE BASE
H. SELECT 1 OF 4 MASSAGE
WAVE SPEEDS
MASSAGE STOP(G)
UÊ *ÀiÃÃÊ>`Ê`Ê-/"*ÊLÕÌÌÊÕÌÊÌiÊÀi`ÊÊ-}>ÌÕÀiÊ}ÌÊ
illuminates and the Massage feature stops. The Massage
feature is designed to automatically shut off after 30 minutes
of continuous use. The unit will reset after 5 minutes, and
the Massage feature will again be available for use.
UÊ 9ÕÊ1-/ÊÃÌ«Ê>ÃÃ>}iÊÌÀÃÊi>VÊÌiÊLivÀiÊ
switching between wave speeds/types.
WAVE MASSAGE SPEED ADJUSTMENTS(H)
UÊ vÊÌiÊ>ÃÃ>}iÊvi>ÌÕÀiÊÃÊvv]Ê«ÀiÃÃÊ>ÞÊ7>ÛiÊ-«ii`Ê
button to initiate the Wave Massage feature. Each button
represents the amount of time the massage spends in
each section (head or foot) before switching. If the Wave
Massage feature is already on, you must first stop the
massage by pressing the STOP button (G), and then press
the desired Wave Speed; otherwise the Wave Massage
feature will not start.
NOTE: If the massage motors are operating and
the “FLAT” button (C) is pressed, the massage
motors will stop operating during the lowering
of the Ergo System. To then resume massage
operation, press the Head and/or Foot Massage
Adjustments (E, F) or select a Wave Speed.
ADDITIONAL WIRELESS REMOTE CONTROL FEATURES
UÊ /Ê>`ÊÊÌiÊÛÃLÌÞÊvÊÌiÊ7ÀiiÃÃÊ,iÌiÊVÌÀÊÊÜÊ
light environments, the buttons are backlit and will light up
when a button is pressed.
UÊ 9ÕÊ>ÀiÊ>LiÊÌÊVÌÀÊÞÕÀÊÀ}Ê-ÞÃÌiÊÜÌÊÌiÊ7ÀiiÃÃÊ
Remote control without pointing the Wireless Remote
control directly at the receiver (best transmission range is
within 9 feet or 3 meters).
A. RAISE (+) / LOWER (-) HEAD
SECTION OF THE BASE
LED SIGNATURE LIGHT
16
Customer Service: 1–800–979–1457
17
Customer Service: 1–800–979–1457

®
Troubleshooting
Troubleshooting
In the event that your TEMPUR®Advanced Ergo System™fails to operate properly, investigate the symptoms and possible
solutions provided in the chart below:
SYMPTOM SOLUTION
Wireless remote control LED Signature Light illuminates
and appears to be operable but will not activate the
Ergo System.
UÊ 6iÀvÞÊÌ>ÌÊÌiÊ«ÜiÀÊVÀ`ÊÃÊ«Õ}}i`ÊÌÊ>ÊÜÀ}]Ê
grounded electrical outlet. A grounded, electrical
surge protection device is recommended. Test the
outlet by plugging in another working appliance.
No features of the
TEMPUR Advanced Ergo System
will activate.
UÊ 6iÀvÞÊÌiÊ,i`ÊÊ}ÌÊÊÌiÊ*ÊVÌÀÊLÝÊ
is lit – if not the unit is not receiving power.
UÊ *À}À>ÊÌiÊÜÀiiÃÃÊÀiÌiÊVÌÀÊÃiiÊÌiÊ
Wireless Remote Control Guide, included with
this product, for programming procedures). Make
certain the Power Down Box is easily accessible.
Relocate the Power Down Box if necessary.
UÊ 1«Õ}ÊÌiÊ«ÜiÀÊVÀ`]ÊÜ>ÌÊ{xÊÃiV`ÃÊ>`Ê«Õ}Ê
the power cord back in to reset the electronic
components.
UÊ 9ÕÀÊÃÕÀ}iÊ«ÀÌiVÌÊ`iÛViÊ>`ÉÀÊiiVÌÀV>ÊVÀVÕÌÊ
breaker may be tripped. Check both to verify.
UÊ 9ÕÀÊÃÕÀ}iÊ«ÀÌiVÌÊ`iÛViÊ>`ÉÀÊiiVÌÀV>ÊÕÌiÌÊ
may be defective. Test the outlet by plugging in
another working appliance.
Wireless Remote Control LED Signature Light
will not illuminate.
UÊ ,i«>ViÊÌiÊL>ÌÌiÀiÃÊÊÌiÊ7ÀiiÃÃÊ,iÌiÊÌÀ°Ê
The unit requires four (4) AAA batteries.
UÊ ÃÕÀiÊÌiÊL>ÌÌiÀiÃÊ>ÀiÊÃÌ>i`ÊVÀÀiVÌÞ°
Head and/or Foot section will elevate but will
not return to the horizontal (flat) position.
UÊ /iÊÀ}Ê-ÞÃÌiÊ>ÞÊLiÊLÃÌÀÕVÌi`°ÊiÛ>ÌiÊ>`Ê
check for an obstruction. Remove the obstruction.
UÊ /iÊi>`ÊÃiVÌÊ>ÞÊLiÊÌÊVÃiÊÌÊÌiÊÜ>°Ê
UÊ /iÊi>`L>À`Ê>ÞÊLiÊÌÊVÃiÊÌiÊi`}iÊvÊ
the mattress. Verify that a 1.5” (38.1mm) to 2”
(50.8mm) distance is between the headboard
brackets and the mattress. Adjust if required.
SYMPTOM SOLUTION
Head or Foot lift function has minor
interference during operation.
UÊ iVÊL>ÌÌiÀiÃÊÊ7ÀiiÃÃÊ,iÌiÊÌÀ]ÊÀi«>ViÊ
with four (4) new AAA batteries if necessary.
UÊ >iÊÃÕÀiÊÌ>ÌÊÞÕÊ>ÀiÊvÜ}ÊÌiÊ`ÕÌÞÊVÞViÊ
of the motors (do not operate more than two (2)
minutes over a eighteen (18) minute period, or
approximately 10% duty cycle).
UÊ *ÀiÃÃÊÌiÊvÌÊLÕÌÌÃÊõÕ>ÀiÞÊEÊ>VVÕÀ>ÌiÞ°
UÊ 7ÀiiÃÃÊ,iÌiÊÌÀÊ>ÞÊLiÊiÝ«iÀiV}Ê
common Radio Frequency Interference from other
radio transmitting devices. Wait several seconds,
and then try pressing appropriate button again. See
FCC Compliance Statement on page 5 of this guide.
Excessive massage motor noise.
UÊ vÊÌiÊLi`ÊÃÊV>Ìi`ÊÊ>À`ÊÃÕÀv>ViÊyÀ}]Ê«>ViÊ
carpet pieces or rubber pieces (not included) under
each leg or caster of your Ergo System.
UÊ 1Ã}ÊÌiÊÜÀiiÃÃÊÀiÌiÊVÌÀ]ÊiiÛ>ÌiÊÌiÊi>`Ê
or foot section a short distance to realign the lift/
lower mechanisms with the bed support platform.
UÊ 6iÀvÞÊÌ>ÌÊÞÕÀÊÀ}Ê-ÞÃÌiÊÃÊÌÊ«ÃÌi`Ê>}>ÃÌÊ
a wall, nightstand, or other object that may cause
the vibration or noise.
UÊ vÊÌiÊÀ}Ê-ÞÃÌiÊÃÊÃÌ>i`ÊÛiÀÊ>ÊLi`ÊvÀ>i]ÊÛiÀvÞÊ
that the massage motors are not causing the bed
frame (or bed frame components) to vibrate.
UÊ 6iÀvÞÊÌ>ÌÊÌiÊi>`L>À`Ê>ÌÌ>ViÌÊ>À`Ü>ÀiÊÃÊ
properly tightened (if used).
A clicking noise is heard under the
bed when raising or lowering.
UÊ /ÃÊÃÊÀ>°Ê/iÊvÌÊÌÀÊÀi>ÞÃʺVV»ÊÜiÊ
they are engaged. No action is required.
Massage motor over heats or stops
UÊ vÊÌiÊÛLÀ>ÌÊÌÀÊÛiÀÊi>ÌÃ]ÊÌiÊ
thermoprotection will turn the motor off. Wait 15
minutes, turn the MASSAGE ON back on. If it does
not come on, turn it off and report the situation to
customer service.
18
Customer Service: 1–800–979–1457
19
Customer Service: 1–800–979–1457

®
Emergency Power Down Cycle
NOTE: In the event that your Ergo System loses
power, there is an Emergency Power Down Box.
This box only functions if there is not power at
the PLC Control Box.
STEP 1
Place two (2) new 9-volt batteries into the Emergency
Power Down Box.
STEP 2
Press the large Red Button until the Red LED lights up
on the Emergency Power Down Box.
STEP 3
Continue to press the Red Button until the base fully
lowers to the flat position. Ensure hands and arms are
not in the path of moving parts.
NOTE: Lowering using this method is much
slower than the standard process.
FOR TECHNICAL SUPPORT OR SERVICE,
PLEASE CHOOSE FROM THE FOLLOWING NUMBERS:
QUESTIONS ABOUT YOUR ERGO SYSTEM BASE:
1-800-979-1457
QUESTIONS ABOUT YOUR TEMPUR-PEDIC MATTRESS
OR TO ORDER ERGO SYSTEM ACCESSORIES:
1-800-821-6621
OR VISIT WWW.TEMPURPEDIC.COM
20