Tenda Fast Ethernet 100Base-TX User manual

Fast Ethernet 100Base-TX
PCI Adapter
User’s Guide
This RSET8139.EXE setup program can configuration an
d
diagnostics PCI adapters. It is in the root directory of the
Driver Diskette that comes with the package. It is used to set
the PCI adapter’s parameter, such as Operating mode, Media
type, Full-duplex, Boot ROM address and Wake On LAN
statrs, on board test…etc.
Run Rset8139.exe setup program. Insert the driver diskette
into floppy driver of the host PC. Then at the DOS prompt,
type the following and press Enter：
A:\>RSET8139 <Enter>
Boot ROM Installation
The optional BootRoM allows you to connect a workstation
Without disk driver to your network Ssystem.
Installation procedure
1.Plug the BootROM into the BootROM socket.
2.Run the RSET8139.EXE to change the configuration to
enable the BootROM at available address.
3.Refer to your Network Operating System installation
guide for detail.(Make image file)
If you need BootROM.please call your dealer for
assistance.When installing the BootROM into the socket.
Please make sure that the BootROM IC mark is in the same
direction as the other ICs on the adapter.Also,see to it that
all the IC legs are in the right holes of the Socket.
Supported Network Drivers
Novell Netware v3.12,4.0,5.0(included Client/Server
drivers)
Microsoft Windows NT V 3.5X,V4.0
Microsoft Windows 95/95 OSR2/98
Microsoft windows 2000
Packet Drivers for FTPTCP/IP,NCSATCP/IP
All products or brand names mentioned are trademarks or
registered trademarks of their respective companies.
Appendix
10Base-T Twisted-pair Cable
The RJ-45 connector used on 10Base-T Ethernet networks is
the 8-pin RJ-45 modular phone jack. The cable used is
0.4~0.6mm round-wire UTP or STP wire cable similar to
that used for ordinary telephone voice transmission.
PinNumber Assignment
1 TransmitData(+)
2Transmit Data(-)
3Receive Data(+)
6Receive Data(-)
4,5,.7,8 Received
10Base-T Phone Jack connector
®

Boot ROM Size……….32K,64K byte EPROM.
Bus Access Method……Bus Master.
Temperature……………0C to 55C(Std Operating)
32F to 104F
Humidity……………….10% to 90% non
Condensing
Dimensions…………….4.72”x2.36”Non-Bracket
(120.1mmx60mm)
Hardware Jnstallation
The section describes the procedure for installing the
adapter.Follow the steps listed below to installThe PCI LAN
adaplter.
1.Power off your PC and remove its cover.
2.Select an empty PCI slot and insert the adapter
Note:If your card support Wake On LAN.Please
Connect the cable to the mother-board.And read the
manual of the mother board to know about how to set up
the Wake On LAN function.
3.Connect your adapter to the network using RJ-45.
4.Power on the PC
5.Rim doagmpstocs RSET8139.EXE program to check
th adapter of hardware configuration,See the section on
“Diagnostic/setup program”for more information.
6.Installation the software driver.Refer to the Software
Drivers section.
Diagnostics/Setup Program
Before running RSET8139.EXE program ,you
Should remove network drivers first,of the
System could be hung up.
Full-Duplex Ethernet for 20Mbps and 200Mbps
throughput.
Automatic configuration through the PCI BIOS.
Programmable PCI burst size.
Provides 32-bit Bus Mastering data transfers.
Diapnostic LINK, Active LEDs for quick
troubleshooting.
Support 32K, 64K EPROMs for remote
BootROM.
Sipport flow control.
(Option)Support Wake On LAN function.
(Option)supportACPI, PCI power management.
LED Indicatiors
The adapter provides two LED indicators for monitoring
network conditions. This section describes the function
of each LED.
Refer to Figure 2
Figure 2 LED indicators
100/10:100/10 Link
Active:Active
Specifications
Standards…………..IEEE802.3,802.3U
Bus Type…………...PCI-Bus Revision2.1
N
etwork Interface….10Base-T and 100Baes-TX.
Full-Duplex…………20Mbps and 200Mbps.
I/O Address…………Automatiocally determined
byPCIBIOS.
Interrupt(IRO)……….INTA ON PCI slot pin
assignment
The 100Base-TX PCI is a 32-bit 10/100Mbps Fast Ethernet
Adapter.It supports IEEE 802.3 10Base-T IEEE 802.3u
100Base-TX,and combines two transmission rate(10/100)
on one RJ-45 connector. This Adapter supports bus
mastering architecture,and both transmission rate offer Full-
Duplex function to connect to Switching Hub.Extensive
driver support for commonly used network operating
systems is available.
Unpacking Information
This product package should contain:
One 10/100Mbps Fast Ethernet Adapter.
One 3.5”Setup & Drivers Diskette Disk.
This User’s Guide.
Product Description
The 100Base-TX has one RJ-45 connector and two LED
Indicators as shown in Figure land Figurt 2.
Figure 1 PCI Fast Ethernet Adapter
Complete compatibility with the 10Base-TX and
100base-TX standards.
Automatically senses media type.