Tennant SweepSmart S20 ELECTRIC Training manual

IB 9006221 (01--2010) 1
INSTRUCTION BULLETIN
No. 9006221
Machine: S20
Published: 01--2010
Rev. 00
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 9006023
SYNOPSIS:
This kit contains the parts needed to install a vacuum wand kit on S20 machines.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 1 hour)
PREPARATION:
1. Park the machine on a clean level surface,
turn off the machine, remove the key, and set
the parking brake.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, turn off
machine, and remove key.
INSTALLATION:
1. Cut the perforated section from the interior of
the hopper cover. Refer to Fig. 1.
FIG. 1
2. Place the vacuum wand adapter onto the front
of the hopper and mark the locations for the
four 0.375” holes and the 2.087” hole onto
the hopper. Refer to Fig. 2 and Fig. 3.
FIG. 2
3. Place the vacuum wand door into the hopper
and mark the locations for the two 0.276”
holes onto the hopper. Refer to Fig. 3.
4. Use a hole saw to cut a 2.087” hole into the
hopper. Refer to Fig. 3.
5. Drill four 0.375” holes into the hopper. Refer
to Fig. 3.
6. Drill two 0.276” holes into the hopper. Refer to
Fig. 3.

IB 9006221 (01--2010)2
FIG. 3

IB 9006221 (01--2010) 3
FIG. 4
7. Drill two 0.0118” holes into the filter cover.
Refer to Fig. 4.
8. Use four hex screws (10), four flat washers
(11), and four hex nuts (12) to install the
vacuum wand adapter (1) and vacuum wand
seal (1) onto the hopper. Refer to Fig. 5.
1
5
10
11 12
Hopper
FIG. 5
9. Install the vacuum wand door gasket (2) onto
the vacuum wand door. Refer to Fig. 6.
11 12
10
2
3
FIG. 6
10. Use two hex screws (10), two flat washers
(11), and two hex nuts (12) to install the
vacuum wand door onto the hopper. Refer to
Fig. 6.

IB 9006221 (01--2010)4
11. Use a plastic pan screw (7) to install each clip
(6) onto the filter cover. Refer to Fig. 7.
6
7
7
6
Filter
cover
FIG. 7
12. Install the trim molding (8) around the edges
of the square hole in the hopper cover. Refer
to Fig. 8 and Fig. 10.
FIG. 8
13. Install the appropriate warning label (13) onto
the vacuum wand (5). Refer to Fig. 10.
14. Stow the vacuum hose (12) into the storage
area in the hopper cover and secure the
vacuum wand (5) into the clips (6) on the filter
cover. Refer to Fig. 9 and Fig. 10.
FIG. 9
15. Using the vacuum wand: Refer to the
Operators Manual for instructions how to use
the vacuum wand.

IB 9006221 (01--2010) 5
Plastic Hopper
Steel Hopper
11
35
6
7
6
7
8
9
10 10
10
11
11
12
1212
2
4
5
Install appropriate
warning label (13) on
to vacuum wand
FIG. 10

IB 9006221 (01--2010)6
Bill of Materials for Wand Kit, Vacuum, CI [S20] -- 9006023
Ref.
Tennant
Part No. Description Qty.
o9006023 )Wand Kit, Vacuum, CI [S20] 1
Y1 1052620 Adapter Wldt, Wand, Vacuum 1
Y2 1047635 Gasket, Door, Wand, Vacuum 1
Y3 1047632 Door Wldt, Wand, Vacuum 1
Y4 9006909 Wand, Vacuum, W/ Label, NA [S20] 1
Y49006910 Wand, Vacuum, W/ Label, CE [S20] 1
Y4 9006911 Wand, Vacuum, W/ Label, JP [S20] 1
Y5 55965 )Seal, Rbr, 0.06, Tube, Vacuum Wand 1
Y6 67004 Clip, Grip, Finger, 1.00--1.88D,White Vyl 2
Y7 360973 Screw, Pan, 12--16 X 0.50, F/ Plstc 2
Y8C460140 Molding, Trim, Pvc, .08--.11, Bulk 37” 1
Y9 54009 Hose Assy, W/2Cuff, 2.0D 120L 2.0/2.0 1
Y10 08716 )Screw, Hex, M6 X 1.00 X 20, SS 6
Y11 32490 Washer, Flat, 0.25, Std 6
Y12 08708 Nut, Hex, Lock, M6 X 1.00, NL 6
Y13 377099 Label, Warning [Do Not Propel W/ Vacuum] 1
Y13 1011280 Label, Warning, Ce [Do Not Propel] 1
Y13 1011279 Label, Warning [Do Not Propel], TJ 1
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452