Terraplasma Medical Plasma care User manual

Instructions for Use
plasma care®
plasma care® spacer

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 2/38
Table of contents
1Imprint.............................................................................................................................................. 4
1.1 Imprint ..................................................................................................................................... 4
1.2 Disclaimer ............................................................................................................................... 4
1.3 Information on the document ............................................................................................. 4
2Notes and symbols......................................................................................................................... 5
2.1 Read and abide by the manual ......................................................................................... 5
2.2 Symbols................................................................................................................................... 5
2.3 Warning and safety notes .................................................................................................... 7
2.3.1 Starting-up the medical device ...................................................................................... 7
2.3.2 Treatment and operation................................................................................................. 8
2.3.3 Cleaning, maintenance and servicing ........................................................................ 10
2.3.4 Medical device malfunction ......................................................................................... 11
2.3.5 Unexpected events ........................................................................................................ 12
2.3.6 Performance characteristics.......................................................................................... 12
3Intended Use, Indications for Use, Side Effects, Complications, and Contraindications .... 13
3.1 Intended use........................................................................................................................ 13
3.2 plasma care® is adjunctive therapy ................................................................................ 13
3.3 Indications for Use ............................................................................................................... 13
3.4 Side effects / Contraindications........................................................................................ 13
4Operator and Patient Profiles ..................................................................................................... 14
4.1 Operator............................................................................................................................... 14
4.2 Patient Profile ....................................................................................................................... 14
5Delivery contents ......................................................................................................................... 15
6Description of the plasma care®............................................................................................... 16
6.1 plasma care® components............................................................................................... 16
6.2 plasma care® user interface ............................................................................................. 16
6.3 plasma care® spacer......................................................................................................... 16
6.4 User interface....................................................................................................................... 17
7Starting the plasma care®.......................................................................................................... 19
8Treatment...................................................................................................................................... 21
8.1 Performing a treatment with the plasma care® ............................................................. 21
8.2 Attaching and removing the spacer................................................................................ 23
8.2.1 Attaching the spacer ..................................................................................................... 23
8.2.2 Removing the spacer ..................................................................................................... 24
8.3 Treating wounds with the plasma care® ......................................................................... 24
Adjunctive use of the plasma care® for decontamination .............................................. 24
8.3.1................................................................................................................................................ 24
8.3.2 Techniques for larger wounds........................................................................................ 25

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 3/38
9Cleaning, maintenance and servicing ..................................................................................... 25
9.1 Cleaning and maintenance.............................................................................................. 25
9.1.1 Cleaning of the plasma care® and docking station ................................................. 25
9.1.2 Cleaning of the plasma source unit ............................................................................. 26
9.1.3 Storage ............................................................................................................................. 28
9.2 Service .................................................................................................................................. 29
10 Orientation, training and support.......................................................................................... 30
10.1 Orientation ........................................................................................................................... 30
10.2 Training ................................................................................................................................. 30
10.3 Service and support ............................................................................................................ 30
10.4 Troubleshooting ................................................................................................................... 30
11 Environmental conditions....................................................................................................... 31
11.1 Operating conditions.......................................................................................................... 31
11.2 Storage conditions .............................................................................................................. 31
11.3 Transport conditions ............................................................................................................ 32
12 Service life ................................................................................................................................ 32
13 Disposal..................................................................................................................................... 33
14 Device Labeling ..................................................................................................................... 34
15 Technical specification .......................................................................................................... 34
16 Ordering replacements and single-use products ............................................................... 35
17 EMC........................................................................................................................................... 36
18 FCC Certification..................................................................................................................... 37

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 4/38
1Imprint
1.1 Imprint
© 2019 terraplasma medical GmbH. All rights reserved. This document may not be reproduced
in part or fully in any form (print, photocopy or by any other method) for any purpose but per-
sonal use without written consent from terraplasma medical GmbH. Nor may this document be
processed, multiplied or distributed using electronic systems. The terraplasma medical GmbH
reserves the right to change this document or amend it by addition at any time without previ-
ous notice. For misprints and damages resulting thereof terraplasma medical GmbH is exempt
from liability. Other brand and product labels, as well as product logos that are mentioned in
this manual are brands of the respective licence holders and are hereby accredited.
terraplasma medical GmbH
Parkring 32
85748 Garching b. München
Germany
Tel: [phone]
E-Mail: [e-mail]
1.2 Disclaimer
The terraplasma medical GmbH is not liable for damage that results from the disregard of this
instruction for use, in particular of the safety and warning notes herein. In such cases the war-
ranty expires.
1.3 Information on the document
Type manual plasma care®
Author terraplasma medical GmbH
Version 0.1
Date 26.05.2020
Caution: U.S. Federal law restricts this device to sale by or on order of a physician.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 5/38
2Notes and symbols
2.1 Read and abide by the manual
Before using the plasma care® the manual needs to be read carefully and com-
pletely. Reading and following the safety guidelines as well as the manual is
compulsory for any use of the device. Non-comliance with the manueal and the
safety instructions can lead to damage of the device, serious injuries and may
even result in life-threatening situations
2.2 Symbols
Refer to instruction for use
Read the instruction for use
Warning! Please read the safety notes carefully. Disregard thereof can result in
injury to persons or damage to property.
Manufacturer’s address
Date of manufacture
Serial number
Lot number / batch code
Order number / device reference of the manufacturer
Presence of high voltage.
In the surroundings of devices that carry this label, disturbances may occur.
Displays the limits of temperature to which the medical device may be exposed
safely.
Displays the limits of relative humidity to which the medical device may be ex-
posed safely.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 6/38
Displays the limits of barometric pressure to which the medical device may be
exposed safely.
Fragile!
Store dry.
Protect the product form direct radiation by sun and light
Check the battery, displays the current battery charge condition and indicates
the charging process.
CE-label with the code number of the notified body.
Piece of equipment of type BF.
Do not reuse.
Do not sterilize again
Use by
Sterilisation procedure: ethylene oxide-(EO)-sterilisation.
Do not use, when packaging is damaged.
Electrical device, do not discard in domestic waste.
IP
Level of protection against intrusion (solid particles) and water.
This symbol is used for information on installation, operation, service and
repair of the medical device that is important, but not associated with any
danger.
Note

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 7/38
2.3 Warning and safety notes
2.3.1 Starting-up the medical device
ID001
Only use the plasma care®, after having read and understood the instructions
for use in its entirety. Non-compliante usage of the devicedue to disregard of
the manual can lead to personal injury or damage to property.
ID002
Only use the plasma care® with the specified line voltage. Otherwise disturb-
ances, outages, smoke emission and even fire can occur.
ID003
Only use the plasma care® in dry rooms, which are not at any risk of explosion
and only in rooms with sufficient ventilation and lighting.
ID004
Do not use excessive force or remove the plug by pulling on the cable as the
cable might be damaged thereby.
ID004b
Only use the original power supply delivered by the manufacturer. The use of
other power supplies is not admissible.
ID005
Do not use excessive force to attach a country-specific adapter plug to the
power supply. The electrical contacts might be damaged thereby.
ID006
Only use the plasma care® in environmental conditions as defined in chapter
11. Excessive heat/cold or humidity can limit the functionality of the plasma
care® or destroy it.
ID007
Wait until the plasma care® has adjusted to the permissible environmental tem-
perature, especially if the plasma care® has previously been transported or
stored under environmental conditions outside of its defined operating condi-
tions.
ID008
Ensure that the plasma care® and in particular the plasma source is not con-
taminated, smutched or damaged.
ID009
Before each use of a spacer, make sure that the sterile packaging is not dam-
aged and has not already been opened prior to usage of the spacer.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 8/38
ID010
Only use the plasma care® with the original components and accessories from
the manufacturer.
ID011
Do not perform any modifications on the plasma care® without permission of
the manufacturer.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
ID012
Do not open the plasma care® under any circumstances. There is danger of
high voltage!
ID013
Before starting-up the plasma care® after it has been transported, the medical
device needs to reach a temperature within the operating conditions (see
chapter 11.1 Operating conditions).
2.3.2 Treatment and operation
ID014
The treatment with the plasma care® may only be performed by instructed
healthcare professionals.
ID015
Only use the plasma care® for its intended medical purpose (see chapter 3)
taking into account its indications and contraindications (see chapter 3).
ID016
Always use the plasma care® in combination with a plasma care® spacer. Using
the plasma care® without a plasma care® spacer is not possible.
ID017
Use a plasma care® spacer for a single patient only. Otherwise cross-contami-
nation may occur.
ID018
Gently place the plasma care® spacer onto the patient’s skin to produce a
closed volume, if possible.
ID019
Prior to the treatment with the plasma care®, you need to remove all wound
dressings and bandages. Furthermore, the wound bed needs to be prepared for
example by debridement (see chapter 8).

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 9/38
ID020
If non-vital tissue, necrotic tissue, fibrin layers or foreign particles are present in
the wound, careful wound bed preparation (using wound rinsing solutions with-
out active components) needs to be performed prior to plasma care® treat-
ment. Otherwise the plasma treatment may not be effective.
ID021
Wound rinsing solutions with active components may not be used immediately
prior to the treatment with plasma care®. When plasma care® treatment is to
be performed, wound bed preparation with a wound rinsing solution free of ac-
tive components needs to be carried out right beforehand.
ID022
The treatment of the wound of a patient with the plasma care® may only be
performed once within a 12-hour window. The same section of a wound may
only be treated for a maximum duration of 3 minutes.
ID022b
The treatment can be interrupted at any time by exerting extended pressure on
the on / off button. Removal of the plasma care® spacer also leads to immedi-
ate interruption of the treatment.
If the treatment cannot be stopped by either of these two methods, the energy
supply of the plasma source can be interrupted by removing the plasma source
unit.
ID023
The plasma care® can cause electronic disturbances during its normal opera-
tion for its intended purpose, which may interfere with the function of other elec-
tronic devices.
ID024
Other electronic devices, especially high frequency devices such as mobile
phones can impact electronic medical devices. The use of plasma care® in di-
rect vicinity of such devices can therefore lead to an increased emission of or a
strongly reduced immunity of the plasma care® against disturbances.
ID024a
The plasma care ® should not be used in direct proximity to other devices or
combined with other devices as this can result in malfunction. In case the use of
the device in a setting as just described cannot be avoided special attention
has to be paid to the plasma care® as well as to all other devices to ensure
proper functioning.
ID025
Do not remove the plasma care® spacer or the plasma source unit under any
circumstances during treatment.
ID026
The plasma care® spacer protects the user and the patient from an unintended
contact with the plasma source through the integrated protection mesh.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 10/38
ID027
Throughout treatment with the plasma care® ozone is generated at a low con-
centration. During the intended use of the plasma care® the legal limits for
ozone are not exceeded; however, the ozone can be detected by its scent.
The ozone is sufficiently diluted by the surrounding air. If the device is used in small
rooms and/or if several plasma care® devices are used in the same room and/or
upon extended treatment periods, a sufficient level of ventilation must be
achieved (for example by opening windows or doors).
The individual sensitivity towards ozone varies widely.
If the plasma care® is used in the presence of people with a chronic respiratory
disease/disorder or in the presence of infants and young children, special care
needs to be taken regarding sufficient ventilation, as these groups of people are
particularly sensitive.
ID028
Upon treatment with the plasma care® ozone is generated at low concentra-
tions. Treatments in the area of the head and particularly of the mouth should
be avoided.
ID028b
Upon treatment with the plasma care® UV radiation is generated at very low
intensity. Avoid treatments around the eyes.
ID029
The application of antiseptics, topical antibiotics, etc. should occur after the
treatment with the plasma care®. Otherwise no statement regarding the effec-
tiveness of the plasma treatment and/or the antimicrobial treatment can be
made.
2.3.3 Cleaning, maintenance and servicing
ID030
Clean the plasma care® after each treatment of a patient as described in
chapter 9 to prevent cross-contamination.
ID031
You may only use deteregents for cleaning of the plasma care® that are de-
scribed in chapter 9.
ID032
Perform the cleaning procedure for the plasma care® using wipe disinfection as
described in chapter 9. Avoid excessive cleaning fluids, for example frequent
use of spray disinfectant, because the electronic components can be dam-
aged. Cleaning by submersion in a solution is prohibited.
ID033
Do not use pointed objects to clean the plasma source. It can be damaged as
a result, which may lead to faulty plasma generation and danger due to high
voltage. Perform the cleaning procedure as described in chapter 9.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 11/38
ID034
Discard the plasma care® spacer safely in compliance with the applicable reg-
ulations for contaminated single-use items.
ID035
If dirt remains on the plasma source after cleaning, the dirty plasma source
needs to be replaced by a new clean plasma source unit.
ID035a
Examine the device (both front and back) for residuals of body fluids, especially
after the treatment of strongly exuding wounds
ID036
When changing the plasma source unit, check the wired contacts between the
plasma care® and the plasma source unit for corrosion. Also check whether the
plasma source unit has been attached to the plasma care® carefully and flush.
ID037
The plasma source unit needs to be cleaned as described at least once a
month.
ID038
If the plasma source unit is used beyond its expected service life the plasma
care® will indicate this via a permanent red glow of the four segments of the
plasma ring and the plasma source unit needs to be replaced.
2.3.4 Medical device malfunction
ID039
When the four segments of the plasma ring glow red permanently, the plasma
care® and particularly the plasma source unit need to be checked for dirt and
damage.
In case of dirt, the plasma source unit needs to be cleaned as described (see
chapter 9.1.2) or replaced.
In case of damage, the plasma source unit needs to be replaced.
If the problem is not resolved subsequently, the plasma care® needs to be send
to the manufacturer for servicing. It is not permitted to carry out any repairs in-
dependently or through third parties.
ID040
Protect the plasma care® from mechanical damage, shocks and drops.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 12/38
2.3.5 Unexpected events
ID041
When you observe discomfort or an abnormal reaction in a patient, the treat-
ment needs to be stopped immediately. If the adverse event is serious, this needs
to be reported to the manufacturer and the responsible authority of the member
state, in which user and/or patient live, immediately.
ID042
When you notice that the environmental conditions change and that the
plasma care® is used outside of its operating requirements and specifications,
the treatment needs to be stopped.
2.3.6 Performance characteristics
The following performance characteristics might be limited if the device is operated in pres-
ence of electromagnetic disturbances:
•The plasma source produces the required cold atmospheric plasma
•A malfunctioning plasma source is recognized via the monitoring system
•The duration of treatment does not exceed the specified time
•The terraplasma spacer can only be used once
•The internal power supply supplies the device with the required voltage and fre-
quency

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 13/38
3Intended Use, Indications for Use, Side Effects, Compli-
cations, and Contraindications
The plasma care® is a medical device for the painless antimicrobial treatment of wounds with
cold atmospheric plasma. It is used with an add-on, the plasma care® spacer,i a sterile single-
use spacer. It requires minimal contact with the patient’s wound or intact skin and is operated
by healthcare professionals.
3.1 Intended use
The aim is to reduce the bacterial and fungal infiltration of a skin wound with the plasma care®.
For this purpose the operator (e.g. a nurse) places the plasma care® with the spacer attached
gently onto the wound, starts plasma generation and keeps the medical device in position until
the treatment is completed (a detailed description can be found in chapter 8).
The bacterial and fungal burden in the wound is reduced through the contact of the gener-
ated plasma species with the microorganisms. Eukaryotic (human) tissue is not damaged.
3.2 plasma care® is adjunctive therapy
The plasma care® can be used as an add-on to regular wound therapy, (i.e. in addition to the
usual community standard treatment methods). Standard procedures using cleaning solutions
/ debridement, topically applied medications or antiseptics, and wound dressings should be
continued.
In general, wound bed preparation using any form of debridement and wound irrigation or
similar water-based solutions should be performed prior to the plasma treatment.However, the
plasma treatment should be carried out prior to the application of any other medications that
remain in the wound.
The full effect of the plasma treatment can only be achieved, if the plasma species come into
direct contact with the bacteria and fungi in the wound.
3.3 Indications for Use
The plasma care® device decreases the microbial flora of skin wounds. The plasma care®
device is an adjunct to standard therapies including wound debridement and topical antimi-
crobial solutions.
The plasma care® device has been shown in vitro to reduce the following bacteria by
greater than 5 log: Staphylococcus aureus, Staphylococcus epidermidis, methicillin resistant
Staphylococcus aureus (MRSA), Pseudomonas aeruginosa, Escherichia coli, Enterococcus
faecalis, Streptococcus agalactiae, Streptococcus constellatus, and Corynebacterium pro-
pinquum.
The plasma care® device has been shown in vitro to reduce Candida albicans by greater
than 4.6 log.
3.4 Side effects / Contraindications
There are no known side effects or complications associated with a treatment using the
plasma care® device.
A treatment with plasma care® is contraindicatd for:

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 14/38
•Wounds without hemostasis
•Wounds with exposed inner organs (e.g., during surgery)
•Wounds at mucous membranes
•Wounds of head and neck area
•Children under the age of 12 years
4Operator and Patient Profiles
4.1 Operator
The plasma care® is a medical device that is intended for use in a professional environment.
The operators are physicians and other healthcare professionals
•in hospitals (e.g. dermatology, surgery, angiology) and wound centers,
•in medical practices (e.g. GPs, dermatologists, diabetologists, surgeons, angiologists
and podologists),
•in out-patient care,
•in retirement and nursing homes or
•in home care setting (e.g. travelling nurses)
The operators have undergone medical training and are experienced in the treatment of
wounds in compliance with the current therapeutic guidelines.
Prior to use of the plasma care® with the plasma care® spacer, all operators need to study the
manual carefully and need to be instructed in the use of the plasma care®. The instruction can
be given by the manufacturer or an expert.
Before using the plasma care® with the plasma care® spacer the operators
need to read the manual carefully.
4.2 Patient Profile
The patients are people with wounds of varying aetiology. The patients need to be at least 12
years of age. As wounds occur more frequently in elderly patients, a higher average age can
be assumed. The patients often display co-morbidities or limitations such as the following:
•limited mobility
•sensory disorders
•metabolic disorders
•circulatory disorders
•venous insufficiency
•peripheral artery disease
•Diabetes mellitus
•neoplasias
The treated wounds are not gender-specific.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 15/38
5Delivery contents
The plasma care® is delivered with the following components:
plasma care® with removable plasma
source unit
docking station
power supply for the docking station
sterile, individually packaged plasma care®
spacer (single use only)
Instruction for Use

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 16/38
6Description of the plasma care®
6.1 plasma care® components
The plasma care® is composed of the device, its docking station with the power supply and
the plasma care® spacer.
The docking station has two functions:
•Safe placement and storage area for the plasma care®.
•Recharging of the plasma care® via contactless, inductive energy transfer as soon as
the plasma care® is placed in the docking station.
As soons as the docking station is plugged in, the control-LED glows blue and the plasma
care® can be recharged.IIt takes about 3 hours to charge the plasma care® completely.
During the charging process the battery symbol of the plasma care® flashes red, yellow
and green.
The removable plasma source unit contains the plasma source, which is composed out of a
high voltage electrode, a dielectric barrier and a grounded electrode in the shape of a mesh
at the front.
6.2 plasma care® user interface
The user interface can be found on the upper side of the plasma care®. The interface allows
the following commands by pressing the touch-button:
•Switching the plasma care® on / off by touching the button for 2 / 5 seconds
•Starting and stopping a treatment by exerting pressure briefly.
The user interface displays the following information via differently colored LED-elements:
•The system status, i.e. on / off, plasma source active
•The battery charge condition
•Warning and error notices
6.3 plasma care® spacer
The spacer (sterile single-use product) is attached to the plasma care® onto the plasma source
unit and has the following functions:
•Designed as a sterile, single-use product to prevent cross-contamination.
plasma care®
docking station

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 17/38
•The integrated safety grid prevents contact of the patient or the operator with the
plasma source integrated into the plasma source unit, while it produces plasma.
•An unambiguous identification of the attached spacer is enabled via an integrated
RFID-transponder. After using the spacer, it is marked as “invalid” and cannot be used
for any further treatments. In case of an invalid spacer, the plasma care® device can-
not be activated.
•With one spacer a maximum of 6 plasma treatments can be performed on a single
patient. The use of a spacer on more than one patient is not permitted due to the cross-
contamination risk.
6.4 User interface
The user interface indicates the system status and is used for controlling the device. The follow-
ing status displays are possible:
On / Off (white):
By exerting extended pressure, the plasma care® is switched on or off. If the plasma care® is
switched on, the On / Off button will glow white.
Plasma ring (blue):
RFID-tag
safety grid
Off
On

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 18/38
Blue flashes:Indicates that a valid spacer is clipped onto the plasma care® and that the prep-
aration period is running.
Blue glow: When the preparation period is completed all four plasma ring segments glow
steadily and the plasma treatment can be started by exerting pressure on the On / Off button
briefly.
When the plasma treatment is started, the individual plasma ring segments will flash one after
the other and will each switch off after a quarter of the treatment time.
Plasma ring (red):
Red flashes: Indicates that the spacer was already used and is invalid. A new spacer must be
used.
Red glow: Indicates a malfunction of the device. Please proceed according to chapter 10.4
Troubleshooting.
Battery symbol (green, yellow, red):
The battery symbol indicates the battery charge condition:
If it glows green, the battery is fully charged. If it glows yellow, the battery is semi-charged. If it
glows red, the plasma care® needs to be re-charged.

Instruction for Use
plasma care and plasma care spacer
IFU plasma care© and plasma care© spacer
Version: 0.1
Date: 26.05.2020
Copyright: terraplasma medical GmbH
Page 19/38
When the plasma care® is placed into the docking station, the battery symbol will alternate
between the green, yellow and red glow for as long as the plasma care® is being re-charged.
When the plasma care® is fully charged the battery symbol will glow green continuously.
Docking station on / off glow
The blue control-LED will glow as long as the docking station is plugged-in.
7Starting the plasma care®
Prior to its first use, the plasma care® needs to be fully charged. For this purpose, carry out the
following steps:
1. Attach the power supply of the docking station to the docking station of the plasma
care®. The connector for the power supply is inside the black indentation at the back
of the docking station.
2. Attach a country-specific adapter plug to the power supply if neccessary.
3. Plug the power supply of the docking station into the power socket. The blue control-
LED of the docking station will start to glow.