Teryair SP10 Instruction Manual

Models Descriptions IMPA Number
SP10 Pneumatic Submersible Pump 2" 59 16 35
SP25 Pneumatic Submersible Pump 2-½" 59 16 36
S P - 10
Read this manual carefully before installing, operating or servicing this equipment. It’s the responsi-
bility of the employer to ensure this manual is read by the operator. Please preserve this manual.
is document is issued with Product Serial No
Operation and Maintenance Guide
S P - 25

FF-MM-321-REV - 03
Page 2
Operation and Maintenance Guide Sump Pump
Table of Contents
3 Introducon
3 Technical Data
3 SafetyInstrucons
4 OperangInstrucons
5 SuggestedLubricants
5 Troubleshoong
6 DiassemblyandRe-assemblyofSP10
7 BillofMaterialsforSP-10
8 ExplodedViewforSP10Pump
9 ExplodedViewDetailAforSP-10Pump
10 ExplodedViewDetailB&DetailCforSP-10Pump
11 DiassemblyandRe-assemblyofSP25
12 ExplodedViewforSP25Pump
13 ExplodedViewDetailAforSP-25Pump
14 ExplodedViewDetailB&DetailCforSP-25Pump
15 BillofMaterialsforSP-25
16 DimensionalData
16 RepairKitsforSP-10&SP-25
17 RepairKitsforSP-10
18 RepairKitsforSP-25
19 TestCercateOfMaterials,Performance
20 EuDeclaraonOfConformity
21 WarrantyCercate

FF-MM-321-REV - 03
Page 3
Operation and Maintenance Guide Sump Pump
Technical Data
Specication SP-10 SP-25
Output in m³/Hr 48 60
Total Head in mtrs 27 24
Air Hose ¾" NPT ¾" NPT
Air exhaust 1" NPT 1¼ BSPP
Fluid Outlet 2" Hose 2½" Hose
Air Consumption, m³/min 2.7 3.5
Min. opening pump will enter 204mm x 230mm 210mm x 305mm
Height 340mm 392mm
Weight, Kgs 22 32
Intended Use
Pneumatic Submersible pumps are intended
for use de-watering ,transfer of uids such as
clear and sea water, marine emptying of ballast
tanks, damming cargo holds and pumping of
sea water from bilges and holds.
It is a single stage centrifugal unit driven by
powerful vane motor. Also double seals protect
bearing and motor from water & mud, and
integral oiler provides continuous lubrication.
Follow the instructions mentioned here to
enhance the life and performance of the pump.
Safety Instructions
Warning
Warning: If not followed could cause personal
injuries
Caution
If not followed could result in damage to
equipment.
Following symbols are used through out this
manual.
Warning
Operators under eighteen not allowed to oper-
ate this Pump. Operators must be made famil-
iar with the instructions in this manual before
attempting to operate the pump.
Caution
Use only genuine Teryair or Teryair approved
accessories.
Caution
Completely turn o the Pump and disconnect
air supply line before attempting any service.
Read Assembly and Disassembly instructions
Warning
is manual must be read and the operating
instructions carefully followed.
Introduction
Teryair Pneumatic Centrifugal Pumps are used to empty ballast tanks, bilge wells, etc. Oen
used for draining cargo holds during and aer the washing procedure. Teryair Centrifugal
pumps have a small cross-section and hence can be lowered into areas having small access
hatches. Especially preferred where an eclectic spark may risk ignition or explosion. Required air

FF-MM-321-REV - 03
Page 4
Operation and Maintenance Guide Sump Pump
Sump pump is rugged dependable equipment
designed to give you years of satisfactory
service. Follow the instructions mentioned here
to enhance life and performance of your pump.
Daily Before Operating
Disconnect and pour in 1 to 2 ounces of
recommended oil into the pump and reconnect
hose aer blowing out any accumulated dirt in
the hose line before connection
Operating Instructions
Caution
A regular maintenance aer every 500 hours of
operation will greatly add to the durability of
the pump.
Warning
Take care not to exceed the maximum 6 bar (90
psi) supply air pressure. Use a lter and regu-
lator and lubricator as close to the Pump inlet
as operation will allow ensuring a clean and
regulated and lubricated air ow.
Caution
Keep hoses in good condition. Check hoses for
signs of wear, cracks & bulges and ensure that
they are secure. Accidental disconnection while
hose is pressurized makes the hose whip and
can be a safety hazard.
Caution
Please check the hose connection prior to
starting pump.
Store these pump in secure & dry environment.
Do not allow the pump to run unattended.
Do not modify this pump in any way as this
will invalidate the warranty and could lead to
serious injury.
Lubrication Requirements
Always install a line lubricator on the air
line as close to the pump as possible. A
Filter Regulator Lubricator unit (FRL)
is strongly recommended. Keep the lu-
bricator bowl topped up with
recommended grade of oil and check that
the oil is reaching the Pump. Running the
Pump without lubrication is likely to cause
damage to the components causing prema-
ture replacement.
Air Supply
e pump work best at 6 bar (90 psi) air
pressure. e air should be clean, dry and
lubricated. Install a FRL unit as close as
operation will permit.
Hoses
Daily before operation check the hoses,
especially the high pressure hoses for
damage or leaks.
Use genuine Teryair spares and if possible
mention the serial number of the pump
when ordering spares.
Storage
When storing sump pump for any length
of time precautions should be taken to
prevent corrosion and to maintain pump
in a serviceable condition.
Remove discharge and exhaust hose or
pipe and run pump out of water to blow
out all moisture
Remove air line and pour a small amount
of rust resistant oil in live air inlet.
Re- connect hose and idle motor a few
minutes to carry oil to all internal parts.
Remove air hose and plug live air inlet and
air exhaust port with corks.
Wipe out side of pump with rust resisting
oil. Wrap pump in oiled paper and pack in
covered box.
Store pump in dry place.

FF-MM-321-REV - 03
Page 5
Operation and Maintenance Guide Sump Pump
Suggested Lubricants
Brand Above 27 Deg C ( From 5 Deg C to 27 Deg C Below 5 Deg C
Shell Toona R.72 Toona R.41 Toona R.27
Mobil Almo 529 Almo 527 Almo 525
Esso -- -- -- -- Arox EP.65 Arox EP.45
Caltex Rando Oil 100 Rando Oil 100 Rando Oil 46
CP -- -- -- -- -- -- -- -- Airolene Tool OiI
Texaco Regal Oil F (R&O) Regal Oil PE (P&E) Regal Oil PE (R&O)
Daltron Silkolene 881 Silkolene 548/T Silkolene 733
Burmah Castrol Castrol RD Oil 3 Castrol RD Oil Light Megna SPX
Duckham Garnet 7 Garnet 6 Zero Fio 5
Sternol Merlin 87 Merlin 71 Merlin 54
Petrona Purifoc 53 Purifoc 46 Purifoc 32
Chevron Vistac Oil 18X Vistac Oil 19X Vistac Oil 9X
Indoil Servo Spyn -22 -- -- -- -- -- -- -- --
Troubleshooting
Serial No Description Causes
1Pump stops and will not start Insucient Air Pressure
Check air pressure is as recommended at the pump air inlet
Air Filter Blocked
Check if debris has clogged the inlet lter on the FRL unit/pump
inlet air valve (some models have air lter on the air inlet valve ) and
ensure clear passage of air
Internal damage or excessive wear on components
Proceed to dismantle the pump, examine component for wear, replace
any worn components, re assemble carefully as instructed in this
manual and re start the pump.
2Pump runs slowly, poor delivery. Insucient or wrong lubricant in the air supply.
Ensure that the lubricant is as per the recommended chart, a thicker
lubricant oen makes the air valve work sluggishly.
Internal damage or excessive wear on components
Proceed to dismantle the pump, examine component for wear, replace
any worn components, reassemble carefully as instructed in this man-
ual and re start the pump.
3Motor is jammed. Worn or damaged rotor blades
Dis -assemble governor housing (7) and
motor housing (35). Clean all parts in a light
solvent. Replace worn or damaged parts and
reassemble.

FF-MM-321-REV - 03
Page 6
Operation and Maintenance Guide Sump Pump
Diassembly and Re-assembly of SP10
a. Unscrew and remove Gate Valve (1), Ex-
haust Pipe (49) and Discharge Nipple (48)
from Impeller Housing (46).
b. Unscrew Allen Bolt (33) with Spring Wash-
er (34) to separate Motor Housing (35)
from Impeller Housing (46).
c. Now unscrew Allen Bolt (8) with Spring
Washer (9) to separate Governor Housing
(7) & Gasket (10) from Motor Housing
(35) and replace it with new one. (If found
damaged)
d. Unscrew Hex Bolt (44) with Spacer (43) to
remove Impeller (42) and Rotor Key (41)
from Rotor (28).
e. Now remove motor assembly (Parts in De-
tail B) from Motor Housing (35).
f. Unscrew Governor Body (22) (Clockwise)
from Rotor (28). Now remove Pin (21) from
Governor Body (22) and remove Governor
Weight (20) and replace it with new one. (If
found damaged)
g. Remove Upper End Plate (24) from Rotor
Body (28) to remove Ball Bearing (23) &
Spacer (27) and replace with new one (If
found damaged)
h. Remove Cylinder (25) and Rotor Blades
(29) from Rotor (28). Now remove Roll Pin
(26) from Cylinder (25) and replace with
new one. (If found damaged)
i. Now press Rotor (28) from Lower End
Plate (31) side to remove Rotor (28). Now
remove Ball Bearing (32) from Lower End
Plate (31) and replace it with new ones. (If
found damaged)
j. Now remove Impeller Sleeve (40) from Up-
per Wear Plate (38) and remove O-ring (50)
& Shim (51) and replace it with new ones.
(If found damaged)
k. Unscrew CSK Screw (39) from Upper Wear
Plate (38) from Impeller Housing (46).
l. l) Now remove Oil seals (37) and
O-rings (36) from Motor Housing (1) and
replace it with new ones. (If found worn-
out)
m. Now insert a 6 mm diameter rod (1/4”) in
to the holes in the underside of Impeller
Housing (46) and evenly tap the Lower
Wear Plate (42) out of the housing.
n. Now unscrew Governor Valve Cage (17)
from Governor Housing (7) . Now unscrew
Bushing (18) from Governor Valve Cage
(17).
o. Now remove Internal Circlip (11) from
Governor Valve Cage (17) using circlip
remover. Now remove Spring Retainer (12),
Spring (13), Governor valve (14) & Pin (15)
from Governor Valve Cage (17) and replace
it with new ones. (If found damaged)
p. Now remove Internal Circlip (2) from Air
Inlet Bushing (4) using circlip remover.
Now remove Air Strainer (3) from Air Inlet
Bushing (4), O-ring (5) and O-ring (6) and
replace it with new ones. (If found dam-
aged)
q. Unscrew Air Inlet Bushing (4) from Gov-
ernor Housing (7). Now remove O-ring (5)
an O-ring (6) from Governor Housing (7).
r. When re - assembling the pump, there
should be a clearance of 0.15 mm (0.007”)
to 0.3 mm (0.012”) add the appropriate
thickness of shims under the Lower End
Plate (31). Insure that the shims slots are
aligned with the three knockout holes in
the Impeller Housing (46). When assem-
bling Motor Housing (35) the Upper End
Plate (24) must protrude above the motor
housing (35), between 0.035 mm (0.001”)
and 0.075 mm (0.003”). If not add shims -
similar to wave washers.
s. Ensure while assembly of Upper End Plate
(24) with Cylinder (25) that holes are
aligned.
t. Now follow the above steps in reverse man-
ner to reassemble the Sump Pump.
Disassembly and Re assembly SP10
Disconnect the air supply to the pump.

FF-MM-321-REV - 03
Page 7
Operation and Maintenance Guide Sump Pump
Bill of Materials for SP-10
Illustration
Number
Part
Number
Description SP-10
1 1999750 GATE VALVE 1
2 5009043 INTERNAL CIRCLIP FOR AIR
STRAINER
1
3 1993828 AIR STRAINER 1
4 1992114 AIR INLET BUSHING 1
5 1994056 O' RING FOR GOVERNOR
HOUSING
1
6 1994034 O' RING FOR AIR INLET
BUSHING
1
7 1990565 GOVERNOR HOUSING 1
8 1999048 ALLEN BOLT 4
9 5009048 SPRING WASHER FOR GOVER-
NOR HOUSING
4
10 1994033 GASKET FOR GOVERNOR
HOUSING
1
11 2004012 INTERNAL CIRCLIP FOR
SPRING RETAINER
1
12 1995041 SPRING RETAINER 1
13 1995040 SPRING FOR GOVERNOR
VALVE
1
14 1992121 GOVERNOR VALVE 1
15 1992120 PIN FOR GOVERNOR VALVE 1
16 1994031 O RING FOR VALVE CAGE 1
17 1992527 GOVERNOR VALVE CAGE 1
18 1992119 BUSHING FOR GOVERNOR
VALVE PIN
1
19 1992125 PUSH PIN 1
20 1992122 GOVERNOR WEIGHT 2
21 1992166 PIN FOR GOV. WEIGHT 2
22 1992124 GOVERNOR BODY 1
23 1995038 BALL BEARING(UPPER) 1
24 1990564 UPPER END PLATE 1
25 1991207 CYLINDER 1
Illustration
Number
Part
Number
Description SP-10
26 1995036 ROLL PIN (LOWER/ UPPER) 2
27 1992115 SPACER (UPPER BEARING) 1
28 1992113 ROTOR 1
29 1993929 ROTOR BLADE 4
30 1992117 SPACER FOR LOWER BEARING 1
31 1990563 LOWER END PLATE 1
32 1995035 BALL BEARING(LOWER) 1
33 1999046 ALLEN BOLT 4
34 1999047 SPRING WASHER 4
35 1990506 MOTOR HOUSING 1
36 1994030 O' RING FOR MOTOR HOUS-
ING
2
37 1994060 OIL SEAL FOR SPINDLE 2
38 1992112 WEAR PLATE UPPER 1
39 1999043 C.S.K. SCREW FOR UPPER
WEAR PLATE
4
40 1992111 IMPELLER SLEEVE 1
41 1995039 ROTOR KEY 1
42 1999801 ASSEMBLY OF IMPELLER AND
LOWER WEAR PLATE
1
43 1992110 SPACER IMPELLER RETAINER 1
44 1999042 HEX. BOLT FOR IMPELLER
RETAINER
1
46 1890508 IMPELLER HOUSING 1
47 1892114 SUMP SCREEN 1
48 1992109 DISCHARGE NIPPLE 1
49 1999045 EXHAUST PIPE 1
50 1904051 O' RING FOR IMPELLER 1
51 1899001 PHILIPS C.S.K. SCREW 3
52 1999052 PIPE PLUG 1
53 1909030 LOCK NUT FOR HANDLE 1
54 1902125 HANDLE 1

FF-MM-321-REV - 03
Page 8
Operation and Maintenance Guide Sump Pump
Exploded View for SP 10 Pump
46
49
52
47
42
48
41
51
50
40
39
38
37
36
35
55
34
33
43
44
54
53
19
21
20
22
23
24
26
25
29
27
28
30
31
32
10
11
12
13
14
15
16
17
18
1
2
3
4
6
5
7
8
9
42
DETAIL A
DETAIL B
DETAIL C

FF-MM-321-REV - 03
Page 9
Operation and Maintenance Guide Sump Pump
Exploded View Detail A for SP-10 Pump
46
52
47
48
55
50
51
41
42
40
53
54
44
43
39
38
37
36
35
49
33
34
DETAIL A
42

FF-MM-321-REV - 03
Page 10
Operation and Maintenance Guide Sump Pump
Exploded View Detail B & Detail C for SP-10 Pump
32
31
30
28
29
24
26
25
27
23
22
20
21
19
DETAIL B DETAIL C
5
6
4
3
2
1
10
11
12
13
14
15
16
17
18
7
8
9

FF-MM-321-REV - 03
Page 11
Operation and Maintenance Guide Sump Pump
Diassembly and Re-assembly of SP25
a. Unscrew and remove Gate Valve (1), Ex-
haust Pipe (36), and Discharge Nipple (47)
from Impeller Housing (48).
b. Unscrew Allen Bolt (38) with Spring
Washer (8) to separate Motor Housing
(37) from Impeller Housing (48).
c. Now Unscrew Allen Bolt (7) with Spring
Washer (8) to separate Governor Housing
(6) from Motor Housing (37) and replace
it with a new one. (If found damaged)
d. Unscrew Impeller (43) from Rotor Body
(25) and replace it with a new one. (If
found damaged).
e. Now remove motor assembly (Parts in
Detail B) from Motor Housing (37).
f. Unscrew Governor Body (18) (Clockwise)
from Rotor Body (25). Now remove Pin
(19) from Governor Body (18) to remove
Governor Weight (17) and replace it with a
new one. (If found damaged)
g. Remove Upper-End Plate (22) from Rotor
Body (25) to remove Ball Bearing (20) &
Spacer (23) from Upper-End Plate (22)
and replace with a new one (If found dam-
aged)
h. Remove Cylinder (29) and Rotor Blades
(24) from Rotor (25). Now remove Roll
Pin (28) from Cylinder (25) and replace it
with a new one. (If found damaged)
i. Now push Rotor Body (25) from Lower
End Plate (30) side to remove Rotor Body
(25). Now remove Impeller Sleeve (41)
from Upper Wear Plate (40) and remove
O-ring (42) and replace it with new ones.
(If found damaged)
j. Now remove Ball Bearing (32) and O-ring
(31) from Lower End Plate (30) and
replace them with new ones. (If found
damaged)
k. Now remove Spacer for Rotor (27) and
O-ring (26) from Rotor Body (25).
l. Now remove the Upper Wear plate (40),
O-ring (39), and Oil Seal (34) from Motor
Housing (37) and replace them with new
ones. (If found damaged)
m. Now remove Seal Plate (35), Oil seal (34),
Gasket (33), and O-ring (21) from Motor
Housing (37) and replace it with new ones. (If
found damaged)
n. Now remove Internal Circlip (15) from Gov-
ernor Housing (6) using Circlip remover to
remove Governor Valve Cage (14).
o. Now remove O-ring (5) from Governor Valve
Cage (14)
p. Now remove Internal Circlip (9) from Gov-
ernor Valve Cage (14) using circlip remover.
Now remove Spring Retainer (10), spring
(11), Governor Valve (12) & Pin (13) from
Governor Valve Cage (14) and replace them
with new ones. (If found damaged)
q. Now remove Internal Circlip (2) from Air
Inlet Bushing (4) using circlip remover. Now
remove Air Strainer (3) from Air Inlet Bush-
ing (4)
r. Now unscrew Air Inlet Bushing (4) from
Governor Housing (6) and O-ring (5) from
Air Inlet Bushing (4) replace it with new
ones. (If found damaged)
s. Now insert a 6 mm diameter rod (1/4”) into
the holes in the underside of impeller housing
(46) and evenly tap the Lower Wear Plate out
of the housing.
t. When reassembling the pump, there should
be a clearance of 0.15 mm (0.007”) to 0.3 mm
(0.012”) add the appropriate thickness of
shims under the lower wear plate (30). Insure
that the shims slots are aligned with the three
knockout holes in the impeller housing (48).
When assembling Motor Housing (37) the
Upper-End Plate (22) must protrude above
the Motor Housing (37), between 0.035 mm
(0.001”) and 0.075 mm (0.003”). If not add
shims - similar to wave washers.
u. Ensure while assembly of Upper-End Plate
(22) with Cylinder (29) that holes are aligned.
v. Now follow the above steps in reverse manner
to reassemble the Sump Pump.
Disassembly and Re assembly SP25
Disconnect the air supply to the pump.

FF-MM-321-REV - 03
Page 12
Operation and Maintenance Guide Sump Pump
Exploded View for SP 25 Pump
42
41
40
39
38
37
36
48
49
46
47
45
44
43
35
34
33
32
31
30
28
29
27
26
25
24
23
22
21 1
2
3
4
5
6
7
8
9
10
11
12
13
15
14
16
20
18
17
19
DETAIL A
DETAIL B
DETAIL C

FF-MM-321-REV - 03
Page 13
Operation and Maintenance Guide Sump Pump
Exploded View Detail A for SP-25 Pump
40
39
38
37
36
49
48
46
47
45
44
43
42
41
8
21
DETAIL A

FF-MM-321-REV - 03
Page 14
Operation and Maintenance Guide Sump Pump
Exploded View Detail B & Detail C for SP-25 Pump
29
28
30
31
32
33
34
35
27
26
25
24
23
22
DETAIL B
6
5
4
3
2
1
20
18
17
19
16
14
13
15
12
11
10
9
8
7
DETAIL C

FF-MM-321-REV - 03
Page 15
Operation and Maintenance Guide Sump Pump
Bill of Materials for SP-25
Illustration
Number
Part
Number
Description SP-25
1 1999750 GATE VALVE 1
2 5009043 INTERNAL CIRCLIP FOR AIR
STRAINER
1
3 1993828 AIR STRAINER 1
4 1992114 AIR INLET BUSHING 1
5 1994034 O' RING FOR AIR INLET
BUSHING
3
6 1900503 GOVERNOR HOUSING 1
7 1909066 ALLEN BOLT 4
8 2109035 SPRING WASHER 8
9 1909098 INTERNAL CIRCLIP FOR
VALVE CAGE
1
10 1905068 SPRING RETAINER 1
11 1905154 SPRING FOR GOVERNOR
VALVE
1
12 1902115 GOVERNOR VALVE 1
13 1902116 PIN FOR GOVERNOR VALVE 1
14 1902569 GOVERNOR VALVE CAGE 1
15 2009007S INTERNAL CIRCLIP 1
16 1902118 PIN FOR GOVERNOR BODY 1
17 1902119 GOVERNOR WEIGHT 2
18 1902117 GOVERNOR BODY 1
19 1992166 PIN FOR GOV. WEIGHT 2
20 1905052 BALL BEARING-UPPER 1
21 1904023 O' RING FOR UPPER END
PLATE
1
22 1900508 UPPER END PLATE 1
23 1902120 SPACER ROTOR BEAR-
ING(UPPER)
1
24 1903938 ROTOR BLADE 4
25 1902121 ROTOR BODY 1
Illustration
Number
Part
Number
Description SP-25
26 1904051 O' RING FOR IMPELLER 1
27 1902122 SPACER ROTOR BEAR-
ING(LOWER)
1
28 3200135 ROLL PIN FOR CYLINDER 2
29 1900505 CYLINDER 1
30 1900507 LOWER END PLATE 1
31 1904022 O' RING FOR LOWER END
PLATE
1
32 1905053 BALL BEARING-LOWER 1
33 1904048 GASKET FOR SEAL PLATE 1
34 1909063 "OIL SEAL FOR SEAL PLATE &
UPPER WEAR PLATE"
2
35 1900506 SEAL PLATE 1
36 1909065 EXHAUST PIPE 1
37 1900502 MOTOR HOUSING 1
38 1909027 "SOCKET HEAD SCREW FOR
MOTOR HOUSING"
4
39 1994030 O' RING FOR UPPER WEAR
PLATE
1
40 1900509 UPPER WEAR PLATE 1
41 1902123 IMPELLER SLEEVE 1
42 1504052 O RING FOR IMPELLER
SLEEVE
1
43 1900504 IMPELLER 1
44 1900510 LOWER WEAR PLATE 1
45 1902125 HANDLE 1
46 1909030 LOCK NUT FOR HANDLE 1
47 1902128 DISCHARGE NIPPLE 1
48 1900501 IMPELLER HOUSING 1
49 1903102 SUMP SCREEN 1

FF-MM-321-REV - 03
Page 16
Operation and Maintenance Guide Sump Pump
Dimensional Data
Repair KIT Ordering No Suitable for
199 97 53 SP 10
190 97 11 SP 25
Repair Kits for SP-10 & SP-25

FF-MM-321-REV - 03
Page 17
Operation and Maintenance Guide Sump Pump
Repair Kits for SP-10
Illu. No. Part No. Description
SP 10
199 97 55 Repair Kit
1 1999750 GATE VALVE WITH 1
6 1994034 O' RING FOR AIR INLET BUSHING 1
10 1994033 GASKET FOR GOVERNOR HOUSING 1
12 1995041 SPRING RETAINER 1
13 1995040 SPRING FOR GOVERNOR VALVE 1
14 1992121 GOVERNOR VALVE 1
15 1992120 PIN FOR GOVERNOR VALVE 1
16 1994031 O RING FOR VALVE CAGE 1
17 1992527 GOVERNOR VALVE CAGE 1
18 1992119 BUSHING FOR GOVERNOR VALVE PIN 1
19 1992125 PUSH PIN 1
20 1992122 GOVERNOR WEIGHT 2
21 1992166 PIN FOR GOV. WEIGHT 2
22 1992124 GOVERNOR BODY 1
23 1995038 BALL BEARING(UPPER) 1
26 1995036 ROLL PIN (LOWER/ UPPER) 2
29 1993929 ROTOR BLADE 4
32 1995035 BALL BEARING(LOWER) 1
36 1994030 O' RING FOR MOTOR HOUSING 2
37 1994060 OIL SEAL FOR SPINDLE 2
42 1999801 ASSEMBLY OF IMPELLER AND LOWER WEAR PLATE 1
44 1999042 HEX. BOLT FOR IMPELLER RETAINER 1
23 199 50 38 BALL BRG 1
24 199 97 50 AIR COCK ASSEMBLY WITH ADAPTORS 1

FF-MM-321-REV - 03
Page 18
Operation and Maintenance Guide Sump Pump
Repair Kits for SP-25
Illu. No. Part No. Description
SP 25
190 97 11 Repair Kit
1 1999750 GATE VALVE 1
5 1994034 O' RING FOR AIR INLET BUSHING 3
7 1909066 ALLEN BOLT 4
8 2109035 SPRING WASHER A10 8
9 1909098 INTERNAL CIRCLIP FOR VALVE CAGE 1
10 1905068 SPRING RETAINER 1
11 1905154 SPRING FOR GOVERNOR VALVE 1
12 1902115 GOVERNOR VALVE 1
13 1902116 PIN FOR GOVERNOR VALVE 1
14 1902569 GOVERNOR VALVE CAGE 1
15 2009007S INTERNAL CIRCLIP 1
16 1902118 PIN FOR GOVERNOR BODY 1
17 1902119 GOVERNOR WEIGHT 2
18 1902117 GOVERNOR BODY 1
19 1992166 PIN FOR GOV. WEIGHT 2
20 1905052 BALL BEARING-UPPER 1
21 1904023 O' RING FOR UPPER END PLATE 1
24 1903938 ROTOR BLADE 4
26 1904051 O' RING FOR IMPELLER 1
28 3200135 ROLL PIN FOR CYLINDER 2
31 1904022 O' RING FOR LOWER END PLATE 1
32 1905053 BALL BEARING-LOWER 1
33 1904048 GASKET FOR SEAL PLATE 1
34 1909063 "OIL SEAL FOR SEAL PLATE & UPPER
WEAR PLATE"
2
38 1909027 "SOCKET HEAD SCREW FOR MOTOR HOUSING" 4
39 1994030 O' RING FOR UPPER WEAR PLATE 1
43 1900504 IMPELLER 1

FF-MM-321-REV - 03
Page 19
Operation and Maintenance Guide Sump Pump
TEST CERTIFICATE OF MATERIALS, PERFORMANCE
Date :
Model number :
Part description & s.No. :
We hereby certify that the above referenced product has tested and inspected in accordance with our standard test procedures
and meets the specications for material and performance values as published in our literature. We further certify that the prod-
uct has been given our standard factory test and meets all quality and performance standards established by the company.
is product is certied to be produced in our factory, and is of current production.
Authorised Signatory
Q.A Manager
Place - Vasai, Maharastra

FF-MM-321-REV - 03
Page 20
Operation and Maintenance Guide Sump Pump
EU DECLARATION OF CONFORMITY
We hereby certify that the Listed Product stipulated below comply with all relevant provisions of the machinery direc-
tive (2006/42/EC) and the national laws and regulations adopting this directive.
Description :
Model Number :
Date :
Serial Number :
Is in conformity with the provisions of the following European Directives: (2006/42/EC) Machinery Safety and
Harmonized standards
ISO 12100-1: 2010: Safety of Machinery –general Principles for Design –Risk Assessment and Risk Reduction.
Registered Oce : 416 Gundecha Industrial Complex, Akuril Road,
Kandivali East, Mumbai – 400101, Maharashtra, India.
Web site : www.teryair.com
Works : A-1, Tirupati Udyog Nagar, Sativali Road, Vasai East,
Palghar – 401208, Maharashtra, India.
CE certication registration no – C E 16832
Issued by – BMQR Certications Pvt Ltd.
www.cemarking-india.com
Valid Till – 03/11/2021
Signed for and on behalf of
TERYAIR EQUIPMENT PVT. LTD. Place of Issue:
Date: