Tescom DS3200H User manual

Βόλου 7, 183 46 Μοσχάτο
Volou 7, 18 346, Moschato, Greece
[phone]
[email protected] www.tescom-ups.gr
DSP CONTROLLED UPS
30 kVA
Uninterruptible Power Supply System
User Manual
3 phase In / 3 phase Out
DS 300H Series

2www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
CONTENTS
I. GENERAL DESCRIPTION ...................................................................................... 3
1.1 Introduction ....................................................................................................... 3
1.2 Design Concept................................................................................................. 5
1.2.1 Description of Blocks................................................................................ 6
1.2.2 Operating conditions of ups...................................................................... 6
1.3 Front view of UPS Connection Panel ................................................................ 7
1.4 Technical Specifications.................................................................................... 9
II. UPS INSTALLATION .............................................................................................. 10
2.1. Introduction ....................................................................................................... 10
2.2. Unpacking......................................................................................................... 10
2.3. Equipment Positioning....................................................................................... 10
2.4. Connecting the UPS Power Cables................................................................... 11
2.5. Safety Earth ...................................................................................................... 11
2.6. Cable Connection Procedure ............................................................................ 11
2.6.1. Description of Connection Terminals of the UPS ....................................... 12
2.7. Battery Installation............................................................................................. 13
III. FRONT PANEL ....................................................................................................... 16
3.1. Introduction ....................................................................................................... 16
3.2. Front Panel Menu Descriptions ......................................................................... 16
3.2.1 MEASUREMENTS menu ........................................................................... 19
3.2.2 ALARM LOGS menu .................................................................................. 22
3.2.3 INFORMATION menu ................................................................................ 22
3.2.4 OPTIONS menu ......................................................................................... 23
3.2.5 COMMAND menu ...................................................................................... 26
3.2.6 TIME menu................................................................................................. 26
3.2.7 SERVICE menu.......................................................................................... 27
3.2.8 ADJUST menu ........................................................................................... 27
3.2.9 User Pasword............................................................................................. 28
3.3. Alarms and warning messages ......................................................................... 28
3.4. Status Codes .................................................................................................... 31
3.5. Alarm messages and quick troubleshooting ...................................................... 37
IV. OPERATING INSTRUCTIONS................................................................................ 42
4.1 Introduction.......................................................................................................... 42
4.2 Operating ups in online mode.............................................................................. 42
4.2.1 Starting ups from a completely shut down position ..................................... 42
4.2.2 Shutting down the ups................................................................................ 42
4.2.3 Switching the UPS from a normal
operation to maintenance bypass condition.............................................. 43
4.2.4 Switching the UPS from a maintenance
bypass condition to normal operation ....................................................... 43
4.3 UPS Behavior During mains outage.................................................................. 44
1
V. PARALLEL OPERATION……………………………………………………………….. 45
5.1 Introduction……………………………………………………………...……...…... 45
5.2
Parallel Operation Mode settings of DS300H Series UPSs…………………….. 46
5.3 Parallel mode status codes of the UPS……………………………………….... 49
VI. PARALLEL OPERATING INSTRUCTIONS………………………………………............54
6.1 INTRODUCTION……………………………………………………………………….... 54
6.2 OPERATING INSTRUCTIONS FOR PARALLEL CONNECTED UPSs…….…….. 54
6.2.1 Starting UPSs from a completely shut down position…………………………....…54
6.2.2 Shutting down the UPS……………………………………………………………….. 54
6.2.3 Switching the UPS from a Normal Operation to Maintenance
Bypass Condition………………………………………………………………….……....…55
6.2.4 Switching the UPS from a Maintenance Bypass Condition
to Normal Operation……………………………………………………………….….…….55
VII. MAINTENANCE......................................................................................................56
7.1 Scheduled maintenance ....................................................................................56
7.2 Daily checks ......................................................................................................56
7.3 Weekly checks...................................................................................................56
7.4 Annual Maintenance..........................................................................................57
7.5 Storage conditions and transportation of ups.....................................................57
VIII. FAULTS AND TROUBLESHOOTING ..................................................................58
8.1. General Procedure for fault checking and troubleshooting.................................58
8.2. Before calling service.........................................................................................58
IX. UPS REMOTE MANITORING AND CONTROL......................................................59
9.1. Using Serial Port................................................................................................59
9.2. Serial Communication port connection cable .....................................................59
9.3. Modem connection ............................................................................................60
9.3.1 Hardware configuration ...............................................................................60
9.3.2 Functioning Principle...................................................................................60
9.3.3 Modem Programming Procedure ................................................................60
9.3.3.1 Smart modem (SM) programming ...................................................60
9.3.4 Modem – UPS Connection Cable................................................................60
9.4. Dry contact (ınterface) connections ...................................................................61
9.5. Remote monitoring panel connection of UPS.....................................................61
X.EFFICIENT USAGE OF UPS IN TERMS OF ENERGY CONSUMPTION....................62

3
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
1
V. PARALLEL OPERATION……………………………………………………………….. 45
5.1 Introduction……………………………………………………………...……...…... 45
5.2
Parallel Operation Mode settings of DS300H Series UPSs…………………….. 46
5.3 Parallel mode status codes of the UPS……………………………………….... 49
VI. PARALLEL OPERATING INSTRUCTIONS………………………………………............54
6.1 INTRODUCTION……………………………………………………………………….... 54
6.2 OPERATING INSTRUCTIONS FOR PARALLEL CONNECTED UPSs…….…….. 54
6.2.1 Starting UPSs from a completely shut down position…………………………....…54
6.2.2 Shutting down the UPS……………………………………………………………….. 54
6.2.3 Switching the UPS from a Normal Operation to Maintenance
Bypass Condition………………………………………………………………….……....…55
6.2.4 Switching the UPS from a Maintenance Bypass Condition
to Normal Operation……………………………………………………………….….…….55
VII. MAINTENANCE......................................................................................................56
7.1 Scheduled maintenance ....................................................................................56
7.2 Daily checks ......................................................................................................56
7.3 Weekly checks...................................................................................................56
7.4 Annual Maintenance..........................................................................................57
7.5 Storage conditions and transportation of ups.....................................................57
VIII. FAULTS AND TROUBLESHOOTING ..................................................................58
8.1. General Procedure for fault checking and troubleshooting.................................58
8.2. Before calling service.........................................................................................58
IX. UPS REMOTE MANITORING AND CONTROL......................................................59
9.1. Using Serial Port................................................................................................59
9.2. Serial Communication port connection cable .....................................................59
9.3. Modem connection ............................................................................................60
9.3.1 Hardware configuration ...............................................................................60
9.3.2 Functioning Principle...................................................................................60
9.3.3 Modem Programming Procedure ................................................................60
9.3.3.1 Smart modem (SM) programming ...................................................60
9.3.4 Modem – UPS Connection Cable................................................................60
9.4. Dry contact (ınterface) connections ...................................................................61
9.5. Remote monitoring panel connection of UPS.....................................................61
X.EFFICIENT USAGE OF UPS IN TERMS OF ENERGY CONSUMPTION....................62

4www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
2
SAFETY
IMPORTANT NOTICES
1. Read instructions carefully before installing and starting the UPS.
2. All warnings in the manual should be adhered to.
3. All operating instructions should be followed.
4. The unit should be supplied by a grounded outlet. Do not operate the unit without a ground source.
5. Power cables of the UPS should be routed carefully so that they are not to be walked on.
6. Please save this manual.
7. Please save or recycle the packaging materials.
WARNING!
•Do not insert any object into ventilation holes or other openings.
•To reduce the risk of fire or electric shock, install in temperature and humidity controlled
indoor area free of conductive contaminants.
•To reduce the risk of fire, replace fuses with the same type and rating when necessary.
CAUTION!
•Only qualified personnel should install or service UPS/batteries.
•Risk of electric shock, do not remove cover. No user serviceable parts inside, refer
servicing to qualified service personnel.
•The output may be energized even when the unit is not connected to a mains supply.
•Risk of electric shock! Hazardous live parts inside. This unit is energized from the
battery supply even when the input AC power is disconnected.
•To reduce the risk of electric shock, disconnect the UPS from the mains supply before
installing a computer interface signal cable. Reconnect the power cables only after signaling
interconnections have been made.
CAUTION !
Units are designed to operate on the concrete floor.
ABOUT THE BATTERIES
CAUTION: RISK OF ELECTRIC SHOCK!
The battery circuit is not isolated from the mains voltage. Hazardous voltages
may occur between the battery terminals and the ground!
•A battery can present a risk of electric shock or burn from high short circuit currents. The
following precautions should be taken when working on batteries :
* Remove watches, rings or other metal objects.
* Use tools with insulated handles.
•The batteries in this UPS are recyclable. Batteries must be disposed of according to local
environmental laws. The batteries contain lead and pose a hazard to the environment and human
health if not disposed of properly.
• Do not dispose of batteries in a fire. The batteries may explode. Do not open or mutilate the
batteries. They contain an electrolyte which is toxic and harmful to the skin and
eyes. If electrolyte
comes into contact with the skin the affected area should be washed immediately.
•The internal energy source (the battery) cannot be de-energized by the user.
•When changing batteries, install the same number and same type of batteries.

5
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
2
SAFETY
IMPORTANT NOTICES
1. Read instructions carefully before installing and starting the UPS.
2. All warnings in the manual should be adhered to.
3. All operating instructions should be followed.
4. The unit should be supplied by a grounded outlet. Do not operate the unit without a ground source.
5. Power cables of the UPS should be routed carefully so that they are not to be walked on.
6. Please save this manual.
7. Please save or recycle the packaging materials.
WARNING!
•Do not insert any object into ventilation holes or other openings.
•To reduce the risk of fire or electric shock, install in temperature and humidity controlled
indoor area free of conductive contaminants.
•To reduce the risk of fire, replace fuses with the same type and rating when necessary.
CAUTION!
•Only qualified personnel should install or service UPS/batteries.
•Risk of electric shock, do not remove cover. No user serviceable parts inside, refer
servicing to qualified service personnel.
•The output may be energized even when the unit is not connected to a mains supply.
•Risk of electric shock! Hazardous live parts inside. This unit is energized from the
battery supply even when the input AC power is disconnected.
•To reduce the risk of electric shock, disconnect the UPS from the mains supply before
installing a computer interface signal cable. Reconnect the power cables only after signaling
interconnections have been made.
CAUTION !
Units are designed to operate on the concrete floor.
ABOUT THE BATTERIES
CAUTION: RISK OF ELECTRIC SHOCK!
The battery circuit is not isolated from the mains voltage. Hazardous voltages
may occur between the battery terminals and the ground!
•A battery can present a risk of electric shock or burn from high short circuit currents. The
following precautions should be taken when working on batteries :
* Remove watches, rings or other metal objects.
* Use tools with insulated handles.
•The batteries in this UPS are recyclable. Batteries must be disposed of according to local
environmental laws. The batteries contain lead and pose a hazard to the environment and human
health if not disposed of properly.
• Do not dispose of batteries in a fire. The batteries may explode. Do not open or mutilate the
batteries. They contain an electrolyte which is toxic and harmful to the skin and
eyes. If electrolyte
comes into contact with the skin the affected area should be washed immediately.
•The internal energy source (the battery) cannot be de-energized by the user.
•When changing batteries, install the same number and same type of batteries.
3
I. GENERAL DESCRIPTION
1.1 Introduction
TESCOM DS300H Series Uninterruptible Power Supplies are double-conversion; three
level on-line UPSʼs manufactured with the latest IGBT and PWM technology, to produce an
uninterruptible, fully DSP (Digital Signal Processor) controlled pure sine wave output to
critical loads.
TESCOM DS300H Series units are 3-phase in/3-phase out devices, and they are
installed between a three phase critical load, and a 3-phase+N mains supply
The advantages of using DS300H UPS:
•Power blackout protection:
If the mains power fails, the UPS continues to supply the critical load using the
energy stored in its batteries, keeping the load immune from power disturbances.
•Increased power quality:
The UPS has its own internal voltage and frequency regulating software, which
ensures that, its output to the critical load is maintained within close tolerances, independent
of voltage and frequency variations on the mains power lines.
•Fully digital control by three DSP controller for each UPS:
The UPS is controlled by 3 independent DSP chips which are communicating each
other continuously. Rectifier, Inverter and User Interface modules have separate DSPʼs to
achieve the highest performance. Each DSP module has many parameters to control and
monitor the system to have the best electrical power output and to help diagnostic.
•Increased noise rejection:
By rectifying the input AC power to DC power and then converting it back to AC
(Double-Conversion) any electrical noise present on the input mains supply line is effectively
isolated from the UPS output. Therefore the critical load is supplied with only clean and
uninterrupted AC power.

6www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
4
Basic Features:
•PWM and IGBT technology
•Three level teknology
•Pure sinusoidal output wave form and true on-line topology
•High input power factor (IGBT rectifier), Input current limiting
•Low input current THD (IGBT rectifier)
•Low output voltage THD
•High AC/AC and DC/AC efficiency (up to 94%)
•3 separate DSP (Digital Signal Processor) control
•Cold-start feature
•Static By-Pass feature: Provides uninterruptable transfer to bypass source in case of
overload or UPS fault.
•Bypass leakage current sense system
•Maintenance bypass switch and warning system, by-pass short circuit protection
•Separate bypass input facility (split bypass), generator operation sense input
•LCD alphanumeric display panel providing battery, load, voltage, power and status
information in detail to user
•Improved diagnostics and correct fault infor mation
•Up to 192 event memory record system (7000 alarms or warnings total)
•Real time clock and calendar system
•Overload operation 10 minutes at 100% - 125% load, 1 minute at 125% - 150% load
•Output overload, over-current and short circuit protection, output current limiting
•Reliable operation at even 100% unbalanced load condition
•Non-linear load supply feature (CF 3:1)
•Double polarity battery (with common terminal)
•Automatic and manual battery test and battery temperature compensation features
•3 separate maintenance clock counters
•Battery charge with current limiting
•Automatic and manual boost charge feature
•Battery deep discharge protection
•Temperature protection with 3 separate sensors
•Interactive communication
•Diagnostic and settings with PC ability
•2 separate RS232 communication ports (standard)
•Multi UPS monitoring on same communication line by RS485 (optional)
•4 dry contact alarm relay outputs as standard (8 optional relay outputs)
•Improved remote monitoring panel system (optional)
•RS232 port multiplexer (optional)
•Direct network connection with optional SNMP support
•MODBUS Adapter (optional)
•AT command set definitions for dump modems
•Communication via Windows based T-MON software and remote monitoring and control of
UPS via modem
•Optional softwares compatible for most computer platforms
•Ability for labeling of UPSs by users
•Emergency power-off support
•Conformity to international and local standards
•AC input and output filters
•Optional graphic front panel
•CE compliance
•Input, bypass and load phase order protection
•Optional leakage current alarm system
•Input and output isolation transformers (optional)
•Enhanced accessory options
•100.000 hours MTBF
•2 years system warranty
•10 years spare parts warranty
5
1.2 Design Concept
S1 (F1-F2-F3) : Rectifier Input Switch / Fuse
S2 (F4-F5-F6) : Bypass Input Switch / Fuse
S3 : Maintenance Bypass Switch
S4 (F7-F8-F9) : Output Switch / Fuse
S5 (F10-F11-F12) : Battery Switch / Fuse
K1 : Rectifier Input Contactor
K2 : Inverter Output Contactor
Rectifier /
Charger
3 PHASE
MAINS I/P
Battery
(Dual Polarity)
Maintenance
Bypass Switch
Static
Bypass
S2
(F4-F5-F6)
S1
(F1
-
F2
-
F3)
S5
(F10
-
F11
-
F12)
S3
S4
(F7-F8-F9)
Inverter
K2
3 PHASE
AC Output
K1

-
-

SB

7
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
5
1.2 Design Concept
S1 (F1-F2-F3) : Rectifier Input Switch / Fuse
S2 (F4-F5-F6) : Bypass Input Switch / Fuse
S3 : Maintenance Bypass Switch
S4 (F7-F8-F9) : Output Switch / Fuse
S5 (F10-F11-F12) : Battery Switch / Fuse
K1 : Rectifier Input Contactor
K2 : Inverter Output Contactor
Rectifier /
Charger
3 PHASE
MAINS I/P
Battery
(Dual Polarity)
Maintenance
Bypass Switch
Static
Bypass
S2
(F4-F5-F6)
S1
(F1
-
F2
-
F3)
S5
(F10
-
F11
-
F12)
S3
S4
(F7-F8-F9)
Inverter
K2
3 PHASE
AC Output
K1

-
-

SB

8www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
6
1.2.1 DESCRIPTION OF BLOCKS
RECTIFIER: In DS300H Series UPSs, a DSP controlled IGBT rectifier with PWM technique is used to
increase input power factor (PFC) and to decrease input current harmonics (THDI).
The IGBT rectifier accepts 3-phase AC input and produces a dual polarity DC voltage for both supplying
the inverter and charging the batteries.
BATTERIES: Batteries are used as reserve DC power supply for the Inverter in case of mains failure. In
DS300H Series, batteries are connected in series with a center-tap output to obtain a dual polarity DC
supply.
Batteries are discharged by the inverter during mains failure. The discharged batteries are re-charged by
the IGBT Rectifier on a constant voltage / current limiting basis, if AC mains power is available.
INVERTER: It is manufactured by using the latest IGBT and DSP (Digital Signal Processing) technologies,
and Pulse Width Modulation (PWM) technique. The Inverter converts the DC BUS voltage supplied by the
IGBT Rectifier and / or the batteries into a well regulated, fully digital controlled 3-phase AC voltage with
fixed voltage and frequency.
The output of the inverter is used to supply the critical loads connected to the UPS output.
STATIC TRANSFER SWITCH (STATIC BYPASS): This is an electronically controlled transfer switch,
which enables the critical load to be connected either to inverter output or to by-pass power source. During
normal operation, the load is supplied by the inverter output, but in case of an overload or a UPS failure it is
automatically transferred to the bypass source without any interruption.
MAINTENANCE BYPASS SWITCH (MBS): This is a manually controlled mechanical switch, which is used
to supply the critical load, using the bypass source, when the UPS is shut down for maintenance or
troubleshooting purposes.
The load is unprotected against mains supply disturbances and black-outs when it is connected to either
static or maintenance bypass supply.
1.2.2. OPERATING CONDITIONS OF UPS
UPS may be in one of the following operating conditions:
A. Normal Operation (If Mains supply is available):
All fuses and power switches are closed (except the Maintenance Bypass Switch), and the load is supplied
by the Inverter Output. During normal operation, the Rectifier supplies DC power to the Inverter and
charges the Batteries at the same time.
B. Battery Operation :
The Batteries are connected to the Rectifier output. In case of a mains failure (mains power outage or AC
input voltage out of tolerance), the Rectifier stops operating and the DC voltage necessary for the inverter
operation is supplied by the batteries. Therefore the AC voltage output supplying the critical load is not
interrupted, until the batteries are fully discharged. At the end of the discharging time the inverter is turned
off and it start again automatically, together with the rectifier, when the mains power is restored, and the
UPS returns o normal operation. For UPS with a split bypass source, at the end of discharging time, static
transfer switch transfers the load to the split bypass source without interruption if the split bypass source is
available and in acceptable tolerances about voltage and frequency, as still the rectifier input is not
available.
The Rectifier is also turned off and inverter operates on batteries during automatic or manual battery test
procedure.
C. By-Pass Operation :
If the Inverter output is overloaded or in case of a problem in the UPS, the static switch transfers the load to
the bypass supply without any interruption, provided that the bypass supply is available and within the
tolerated limits regarding voltage and frequency. At the end of the overloading period, if the fault condition
is restored, static switch transfers the critical load again to the inverter output. Note that, during operation
from the bypass supply, the critical load may be effected by any possible disturbances or power failure in
the bypass supply.
7
1.3 Front view of UPS Connection Panel
Figure 1.3.a 10-15-20 kVA Fuses and Switches Panel
COM1 - RS232
Communication Socket
(DB9 Female)
Relay Output Contacts and Inputs
S7
On / Off
Switch
S1
(AC Input, F1-F2-F3)
S3
(Maintenance By-pass)
S2
(By-Pass, F4-F5-F6)
S4
(AC Output, F7-F8-F9)
SNMP Adapter
(Optional)
COM2 - RS232
Communication Soc
ket
(DB9 Female)
Battery
Circuit
Breaker
Generator
input
Repo
input
TH1
Sensor
Relay
2
Relay
3
Relay
4
S5
(Battery Input, F10-F11-F12)
Parallel Port 2
(Optional)
Parallel Port 1
(Optional)

9
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
7
1.3 Front view of UPS Connection Panel
Figure 1.3.a 10-15-20 kVA Fuses and Switches Panel
COM1 - RS232
Communication Socket
(DB9 Female)
Relay Output Contacts and Inputs
S7
On / Off
Switch
S1
(AC Input, F1-F2-F3)
S3
(Maintenance By-pass)
S2
(By-Pass, F4-F5-F6)
S4
(AC Output, F7-F8-F9)
SNMP Adapter
(Optional)
COM2 - RS232
Communication Soc
ket
(DB9 Female)
Battery
Circuit
Breaker
Generator
input
Repo
input
TH1
Sensor
Relay
2
Relay
3
Relay
4
S5
(Battery Input, F10-F11-F12)
Parallel Port 2
(Optional)
Parallel Port 1
(Optional)

10 www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
8
Figure 1.3.b 30 kVA Fuses and Switches Panel
S5
(Battery Input, F10-F11-F12)
S1
(AC Input, F1-F2-F3)
S3
(Maintenance By-pass)
S2
(By-Pass, F4-F5-F6)
S4
(AC Output, F7-F8-F9)
COM1 - RS232
Communication Socket
(DB9 Female)
S7
On / Off
Switch
SNMP Adapter
(Optional)
COM2 - RS232
Communication Soc
ket
(DB9 Female)
Relay Output Contacts and Inputs
Battery
Circuit
Breaker
Generator
input
Repo
input
TH1
Sensor
Relay
2
Relay
3
Relay
4
Parallel Port 2
(Optional)
Parallel Port 1
(Optional)
9
1.4 Technical Specifications
MODEL DS310H DS315H DS320H DS330H
Output (KVA) 10 kVA 15 kVA 20 kVA 30 kVA
Output (KW) 9 kW 13,5 kW 18 kW 27 kW
Output Power Factor 0,9
INPUT
Number of Phases 3 Phase + Neutral
Input Voltage 220/380, 230/400 or 240/415 Vac
Input Voltage Tolerance +20% , -25% (+15% at 240/415Vac)
Input Power Factor (PF) 0,98 - 0,99 (at full load)
Input THDI <= 4% (at full load)
Input Frequency 50 Hz. ±5%
By-pass Voltage 220/380, 230/400 or 240/415 Vac 3 Phase + Neutral
By-pass Frequency 50 Hz. ±2%
RFI Level EN62040-2
OUTPUT
Number of Phases 3 Phase + Neutral
Output Voltage 220/380, 230/400 or 240/415 Vac
Output Voltage Tolerance ±1%
Output Frequency 50 Hz.
Output Frequency Tolerance (Synchronous) ±2%
Output Frequency Tolerance (Battery) ±0,2%
Efficiency (100% Load) up to 94%
Load Crest Factor 3:1
Output Voltage THD (linear load) <3%
Overload 125% Load 10min. , 150% Load 1min.
BATTERY
Total Number 60 blocks 12V (2x30 serial 60 batteries)
Float Charge Voltage (25
0
C) ±405V DC
End of Discharge Voltage ±300V DC
Battery Test Automatic and Manual
Boost Charge Available
COMMUNICATION INTERFACES
RS232 Com Port 2 each standard (COM1 and COM2)
External Temperature Measurement Input Available (standard)
RS485 Comm. Port Optional
Remote Monitoring Panel Optional
SNMP Adapter Optional
Modbus Adapter Optional
Alarm Relay Contacts 4 each dry contacts (function programmable) 8 optional
Digital Inputs 2 each optional
Emergency Power-Off Input Available (standard)
ENVIRONMENT
Operating Temperature 0 – 40
0
C
Operating Humidity <= %90 (non-condensing)
Acoustic Noise <55dB <57dB <61dB
Dimensions (WxDxH) (mm) 400x815x1035
Device Type and Protection Class Class 1 – IP20
Weight (Without Batteries) (app. kgs) 87 91 100

11
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
9
1.4 Technical Specifications
MODEL DS310H DS315H DS320H DS330H
Output (KVA) 10 kVA 15 kVA 20 kVA 30 kVA
Output (KW) 9 kW 13,5 kW 18 kW 27 kW
Output Power Factor 0,9
INPUT
Number of Phases 3 Phase + Neutral
Input Voltage 220/380, 230/400 or 240/415 Vac
Input Voltage Tolerance +20% , -25% (+15% at 240/415Vac)
Input Power Factor (PF) 0,98 - 0,99 (at full load)
Input THDI <= 4% (at full load)
Input Frequency 50 Hz. ±5%
By-pass Voltage 220/380, 230/400 or 240/415 Vac 3 Phase + Neutral
By-pass Frequency 50 Hz. ±2%
RFI Level EN62040-2
OUTPUT
Number of Phases 3 Phase + Neutral
Output Voltage 220/380, 230/400 or 240/415 Vac
Output Voltage Tolerance ±1%
Output Frequency 50 Hz.
Output Frequency Tolerance (Synchronous) ±2%
Output Frequency Tolerance (Battery) ±0,2%
Efficiency (100% Load) up to 94%
Load Crest Factor 3:1
Output Voltage THD (linear load) <3%
Overload 125% Load 10min. , 150% Load 1min.
BATTERY
Total Number 60 blocks 12V (2x30 serial 60 batteries)
Float Charge Voltage (25
0
C) ±405V DC
End of Discharge Voltage ±300V DC
Battery Test Automatic and Manual
Boost Charge Available
COMMUNICATION INTERFACES
RS232 Com Port 2 each standard (COM1 and COM2)
External Temperature Measurement Input Available (standard)
RS485 Comm. Port Optional
Remote Monitoring Panel Optional
SNMP Adapter Optional
Modbus Adapter Optional
Alarm Relay Contacts 4 each dry contacts (function programmable) 8 optional
Digital Inputs 2 each optional
Emergency Power-Off Input Available (standard)
ENVIRONMENT
Operating Temperature 0 – 40
0
C
Operating Humidity <= %90 (non-condensing)
Acoustic Noise <55dB <57dB <61dB
Dimensions (WxDxH) (mm) 400x815x1035
Device Type and Protection Class Class 1 – IP20
Weight (Without Batteries) (app. kgs) 87 91 100
H MODELS / P.F = 0,9 DS330H DS340H DS360H DS380H DS3100H DS3120H DS3160H DS3200H DS3250H DS3300H DS3400H
TESCOM CODE UPS.0647 UPS.0276 UPS.0649 UPS.0650 UPS.0651 UPS.0652 UPS.0653 UPS.0654 UPS.0655 UPS.0656 UPS.0321
HB MODELS / P.F = 1 DS330HB DS340HB DS360HB DS380HB DS3100HB DS3120HB DS3160HB DS3200HB DS3250HB DS3300HB DS3400HB
TESCOM CODE UPS.0641 UPS.0555 UPS.0556 UPS.0557 UPS.0558 UPS.0559 UPS.0560 UPS.0561 UPS.0671 UPS.0616 UPS.0642
Power (kVA) 30 40 60 80 100 120 160 200 250 300 400
INPUT
Voltage 380/400 VAC 3P + N + G ± 20% (at 100% load) / - 40% (at 70% load)
Frequency 50Hz / 60Hz , ± 5%
Power factor (at 100% load) ≥ 0.99
THDI (*) ≤ 3%
By-pass voltage 380/400 VAC 3 Phase + N, ± 10%
Voltage distortion ≤ 10%
Protections Fuses, Voltage & Frequency tolerance, Input power limit, Phase sequence indicator
OUTPUT
Power (kW) H Models P.F = 0,9 27 36 54 72 90 108 144 180 225 270 360
Power (kW) HB Models P.F = 1 30 40 60 80 100 120 160 200 250 300 400
Power factor H MODELS = 0.9 / HB MODELS =1
Voltage 380/400 VAC 3P + N, ± 1% (415 VAC optional )
Frequency 50Hz / 60Hz
Frequency tolerance Line synchronized: ± 2% (adjustable) / Free running: ± 0,1%
Efficiency up to 95%
Crest factor 3:1
Overload capacity 100% - 125% load: 10 min, 125% - 150% load: 1 min, - > 150% load: by pass
Other protections Advanced short circuit, Voltage tolerance, DC balance, Regenerative load, Current limiting
Voltage THD ≤ 3% (at 100% linear load)
BATTERY
Type VRLA AGM / GEL / NiCd
Number of batteries 2x30 (±30) : 60 pieces
Charge voltage 2x405 VDC
End of discharge voltage 2x300 VDC
Battery cabinet Internal External
Battery ambient temperature 25ºC
Protections 3 level alarms, Battery fuses, Charging current limit, Temperature compensation (optional)
Automatic testing Standard every 72 hours (adjustable)
GENERAL
Standards EN62040-1, EN62040-2, EN62040-3
User interface 4 lines LCD panel, Mimic LEDs, 5 vector buttons, Buzzer, Optional TFT panel
Indicators P-N voltage, P-P voltage, Current, Power, Crest Factor, Frequency, PF, Service Time
Advanced Self diagnostics, 3 maintenance time indicators, Calibration over RS232,operating hour meter
Communication 2xRS232 serial ports, 4 standard and 8 optional DRY contact alarm relays
Inputs EPO input, Interactive battery panel input, Genset input
Genset kit Standard (programmable)
Software Standard T-Mon UPS Management Software (3 clients + 1 server management)
Alarm logging Standard: with time & date 512 events
Protections Power module over-temperature, Over-current, Temperature high alarm
Temperature ranges 0ºC - 40ºC
Protection degree IP20
Relative humidity 90% max. (non-condensing)
Altitude < 1000m above sea level
Acoustic noise < 57 dBA < 62 dBA < 65 dBA < 68 dBA
Net weight (kg) 100 173 197 209 220 232 265 470 525 635 680
Dimensions (mm) HxWxD 1040x400x815 1440x515x855 1900x880x775 1900x1250x775
OPTIONS
Transformer Galvanic isolation transformer at the input & output (internal)
Software T-Mon Admin Multi UPS monitoring 10-50-100-200 clients, T-Mon Server 50-100-200 clients
Adaptors SNMP, RS485, Remote monitoring panel, MODBUS (RS485 or TCP/IP), USB Alarm Logger, TCP/IP, GSM/GPRS Modem, Comport multiplexer
Parallel operation up to 8 units

12 www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
10
II. UPS INSTALLATION
2.1 Introduction
WARNING!!!
•Do not apply electrical power to the UPS equipment before the arrival of authorized service
personnel.
•The UPS equipment should be installed only by qualified service personnel.
•The connection of the batteries and the maintenance should be done by qualified service
personnel.
•Do not make any short- circuit to the battery poles. Because of high voltage and high short-
circuit current, there is risk of electrical shock or burn.
•Eye protection should be worn to prevent injury from accidental electrical arcs. Remove rings,
watches and all metal objects. Only use tools with insulated handles. Wear rubber gloves.
This chapter contains location installation information of the UPS and the batteries. All the
establishments have their own specialties and needs. So in this part, the installation procedure is
not being explained step by step. Instead, general procedure and the applications are explained
for the technical personnel.
2.2 Unpacking
The UPS is packed and enclosed in a structural cardboard carton to protect it from damage.
1) Inspect for damage that may have occurred during the shipment If any damage is noted, call
the shipper immediately and retain the shipping carton and the UPS.
2) Carefully open the carton and take the UPS out.
3) Retain the carton and packing material for future use.
Unit package contents:
1) A user manual and Guarantee certificate.
2) Battery cabinet and/or shelf (Optional)
3) Battery connection cables.
2.3 Equipment Positioning
ATTENTION: Units are designed to operate on the concrete floor.
1. The equipmentʼs installation place must be an easy serving place.
2. Install the UPS in a protected area with adequate air flow and free of excessive dust.
3. You must therefore allow for a minimum gap of 250 mm behind the unit to allow adequate air
flow
4. Select a suitable place (temperature between 0°C and 40°C) and the relative humidity (%90
max)
5. It is recommended to place the equipment in an air-conditioned the room (24°C)
6. Temperature is a major factor in determining the battery life and capacity. Keep batteries away
from main heat sources or main air inlets etc.
7. In case of an operating the UPS in a dusty place, clean the air with a suitable air filtration
system.
8. Keep out of your equipment from explosive and flammable items.
9. Avoid direct sunlight, rain, and high humidity.
WARNING!!! Check the capacity of the forklift if it is available for lifting.
DO NOT LEAN OR LIFT THE UPS CABINET AFTER THE BATTERIES HAVE
BEEN INSTALLED.
11
2.4 Connecting the UPS Power Cables
WARNING!!! A separate power line should be used to supply the UPS AC input. Never use the
same line to supply another electrical device. Do not use any additional cable to
increase the length of the UPSʼs input cable. It is advised to use an MCCB suitable
for the input current on the UPSʼs input line.
The connection of the electrical panel should be supplied by a grounded outlet. Otherwise,
the UPS and the load connected to the output will be left ungrounded. The
grounding system must be checked, and must be strengthen if required. Potential
difference between ground and neutral must be less than 3V AC.
Descriptions of the UPS input output cable connection terminals are shown in figure 2.1
Recommended input line cable and fuse ratings are given in the table below.
UPS power
(kVA)
Recommended cable size (mm
2
)
Line input Bypass input /
UPS output External Battery
Input / output
Cable connections
U-V-W-N
Battery
connections
+ & -
10 10 10 6 16mm
2
terminal 16mm
2
terminal
15 10 10 10 16mm
2
terminal 16mm
2
terminal
20 10 10 10 16mm
2
terminal 16mm
2
terminal
30 16 16 16 16mm
2
terminal 16mm
2
terminal
NOTES: The neutral conductor should be sized for 1,5 times the output/bypass phase current. These
recommendations are for guideline purposes only and are superceded by local regulations
and codes of practice.
2.5 Safety Earth
The safety earth cable must be connected to the earth BUS BAR and bonded to each cabinet in
the system and also the earthing and neutral bonding arrangements must be in accordance with
the local laws.
ATTENTION!!! Failure to follow adequate earthing procedures can result in electric shock hazard to
personnel, or the risk of fire.
2.6 Cable connection procedure
WARNING!!! All connections of the UPS must be done by qualified service personnel
After positioning the UPS, the cables must be connected as described below:
1. Verify all switches and fuses in front of the UPS are at “0” position. (OFF)
2. Connect the 3 phase AC input coming from the mains distribution panel to the AC input terminals as
shown on the label. (Figure 2.1)
ATTENTION!!!: ENSURE CORRECT PHASE SEQUENCE.
If there is a phase sequence error, UPS doesnʼt transfer the load to INVERTER output. If
you canʼt see SYNC:OK in the INFORMATION MENU on LCD, then change the input phase sequence.
3. Connect the output of the UPS to the load distribution panel.
4. Connect the battery groups. Refer to battery installation section.

13
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
11
2.4 Connecting the UPS Power Cables
WARNING!!! A separate power line should be used to supply the UPS AC input. Never use the
same line to supply another electrical device. Do not use any additional cable to
increase the length of the UPSʼs input cable. It is advised to use an MCCB suitable
for the input current on the UPSʼs input line.
The connection of the electrical panel should be supplied by a grounded outlet. Otherwise,
the UPS and the load connected to the output will be left ungrounded. The
grounding system must be checked, and must be strengthen if required. Potential
difference between ground and neutral must be less than 3V AC.
Descriptions of the UPS input output cable connection terminals are shown in figure 2.1
Recommended input line cable and fuse ratings are given in the table below.
UPS power
(kVA)
Recommended cable size (mm
2
)
Line input Bypass input /
UPS output External Battery
Input / output
Cable connections
U-V-W-N
Battery
connections
+ & -
10 10 10 6 16mm
2
terminal 16mm
2
terminal
15 10 10 10 16mm
2
terminal 16mm
2
terminal
20 10 10 10 16mm
2
terminal 16mm
2
terminal
30 16 16 16 16mm
2
terminal 16mm
2
terminal
NOTES: The neutral conductor should be sized for 1,5 times the output/bypass phase current. These
recommendations are for guideline purposes only and are superceded by local regulations
and codes of practice.
2.5 Safety Earth
The safety earth cable must be connected to the earth BUS BAR and bonded to each cabinet in
the system and also the earthing and neutral bonding arrangements must be in accordance with
the local laws.
ATTENTION!!! Failure to follow adequate earthing procedures can result in electric shock hazard to
personnel, or the risk of fire.
2.6 Cable connection procedure
WARNING!!! All connections of the UPS must be done by qualified service personnel
After positioning the UPS, the cables must be connected as described below:
1. Verify all switches and fuses in front of the UPS are at “0” position. (OFF)
2. Connect the 3 phase AC input coming from the mains distribution panel to the AC input terminals as
shown on the label. (Figure 2.1)
ATTENTION!!!: ENSURE CORRECT PHASE SEQUENCE.
If there is a phase sequence error, UPS doesnʼt transfer the load to INVERTER output. If
you canʼt see SYNC:OK in the INFORMATION MENU on LCD, then change the input phase sequence.
3. Connect the output of the UPS to the load distribution panel.
4. Connect the battery groups. Refer to battery installation section.

14 www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
12
WARNING :
- CHECK BOTH OF THE BATTERY GROUPS FOR CORRECT POLARITY AND VOLTAGE
- DO NOT TURN ON THE BATTERY SWITCH (F5) BEFORE STARTING THE UPS
5. Connect the copper earth bus, to the safety earth of the mains distribution panel.
NOTE : The earth and the neutral connections must be in accordance with the local rules.
WARNING: Note that the Input Neutral (N1) MUST also be connected to K10 terminal
2.6.1 Description of connection terminals of the UPS :
•As shown on the power connection label of the UPS, U1, V1 and W1 phase of the incoming 3 phase
supply are used as the bypass inputs under normal conditions, if there is not a separate bypass supply
(split bypass).
•If there is a separate 3- phase AC supply for bypass (Split Bypass):
a-) Remove the links between K4 – K5, K6 – K7 and K8 – K9.
b-) Connect the phases of the bypass source U2, V2 and W2 to K5, K7 and K9 respectively.
c-) Connect the Neutral (N2) of the Bypass source to K11.
Note that the Neutral of the 3 phase input supply (N1) and the Neutral of the 3-phase bypass supply (N2)
must always be connected together to form the Neutral of the AC output.
Figure 2
.
2
10-15-20-30 kVA Cable Connection
R
ectifier Inputs
(3 P+N AC)
By
-
Pass
Input
(3 P+N AC)
UPS Output
(3 P+N AC)
(+)
Battery
Group
(
-
)
Battery
Group
+
(
+
13
2.7 Battery Installation
WARNING!!! Be careful while connecting batteries.
ATTENTION!!! Open the battery switch/fuse before making any connection on the batteries.
The batteries associated with the UPS equipment are usually contained in a purpose-built battery cabinet.
In DS300H Series 10-15-20 and 30 KVA UPSs, there is enough space for 60 pieces of 12V 7Ah
maintenance free batteries.
Where battery racks are used, they should be sited and assembled in accordance with the battery
manufacturerʼs recommendations. In general, batteries require a well-ventilated, clean and dry environment
at reasonable temperatures to obtain efficient battery operation.
In general a minimum space of 10 mm must be left on all vertical sides of the battery block. A minimum
clearance of 20 mm should be allowed between the cell surface and any walls. All metal racks and cabinets
must be earthed.
2 Unpack each battery and check its terminal voltage with a suitable load. Any battery with terminal
voltage less than 10,5V must be charged before installation.
3 Please check the battery connecting hardware and documents. (cables, trays, connection diagrams)
4 Please locate suitable number of batteries on each rack, according to the battery installation and
connection diagram given with the unit.
5 Start locating the batteries from top to the bottom on the racks.
6 Be careful about the connection between the racks and polarities.
7 After interconnecting the batteries, connect “+”, “0” and “-“ leads of the batteries to the battery input
terminals on the UPS. Be careful to connect the batteries correctly and do not turn on (S5) before
checking all connections and before starting the UPS. In DS300H Series UPS, 60 blocks of batteries
are connected in series, in such a way that they form two strings of batteries with opposite polarity; with
a center tap connection to the NEUTRAL (N1-N2) internally.
NOTE THAT SEPARATE CABLES FROM EACH BATTERY GROUP SHOULD BE CONNECTED TO K2
TERMINALS TO FORM THE MIDPOINT CONNECTION.
WARNING!!! NEVER TURN ON S5 (BATTERY FUSE) WITHOUT CENTER POINT CONNECTION TO K2.

15
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
13
2.7 Battery Installation
WARNING!!! Be careful while connecting batteries.
ATTENTION!!! Open the battery switch/fuse before making any connection on the batteries.
The batteries associated with the UPS equipment are usually contained in a purpose-built battery cabinet.
In DS300H Series 10-15-20 and 30 KVA UPSs, there is enough space for 60 pieces of 12V 7Ah
maintenance free batteries.
Where battery racks are used, they should be sited and assembled in accordance with the battery
manufacturerʼs recommendations. In general, batteries require a well-ventilated, clean and dry environment
at reasonable temperatures to obtain efficient battery operation.
In general a minimum space of 10 mm must be left on all vertical sides of the battery block. A minimum
clearance of 20 mm should be allowed between the cell surface and any walls. All metal racks and cabinets
must be earthed.
2 Unpack each battery and check its terminal voltage with a suitable load. Any battery with terminal
voltage less than 10,5V must be charged before installation.
3 Please check the battery connecting hardware and documents. (cables, trays, connection diagrams)
4 Please locate suitable number of batteries on each rack, according to the battery installation and
connection diagram given with the unit.
5 Start locating the batteries from top to the bottom on the racks.
6 Be careful about the connection between the racks and polarities.
7 After interconnecting the batteries, connect “+”, “0” and “-“ leads of the batteries to the battery input
terminals on the UPS. Be careful to connect the batteries correctly and do not turn on (S5) before
checking all connections and before starting the UPS. In DS300H Series UPS, 60 blocks of batteries
are connected in series, in such a way that they form two strings of batteries with opposite polarity; with
a center tap connection to the NEUTRAL (N1-N2) internally.
NOTE THAT SEPARATE CABLES FROM EACH BATTERY GROUP SHOULD BE CONNECTED TO K2
TERMINALS TO FORM THE MIDPOINT CONNECTION.
WARNING!!! NEVER TURN ON S5 (BATTERY FUSE) WITHOUT CENTER POINT CONNECTION TO K2.

16 www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
14
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
30x12V
Batteries
30x12V
Batteries
( + ) ( 0 ) (
- )
360V 360V
( 0
)
K1 K2 K3
K2
Figure 2.3 External Battery Connections (60x12V)

17
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
14
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
30x12V
Batteries
30x12V
Batteries
( + ) ( 0 ) (
- )
360V 360V
( 0
)
K1 K2 K3
K2
Figure 2.3 External Battery Connections (60x12V)
15
K3
K1
K2-K2
Figure 2.3
DS300H Series, 10
-
15
-
20
-
30
KVA
Internal Battery Connections (2x30=60x12V 7Ah)

18 www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
16
III. FRONT PANEL
3.1 Input
The front panel of UPS, consisting of a 4 lines alphanumeric display, 7 status lamps, plus 5
function keys, allows the complete monitoring of the UPS status. The mimic flow diagram helps to
comprehend the operating status of the UPS. By using the function keys operator can moves on
menus and change some parameters.
Figure 3.1 Control panel oft he UPS
L1 :
Maintenance bypass switch on indicator lamp
L2 :
Load on bypass indicator lamp
L3 :
Input voltage indicator lamp
L4 :
Rectifier run pilot lamp
L5 :
Battery operation indicator lamp
L6 :
Load on UPS indicator lamp
L7 :
Output switch on indicator lamp
There are 5 control buttons on the UPS Front panel ,ENTER button provides selection decleration,up and
down buttons provides to surf on menus, (+) and (-) buttons are used for adjustments or option selection.
3.2 Front Panel Menu Descriptions :
By using (↑), (↓) and ENTER buttons you can access the following menus. At the end of each menu there
is <ENTER> EXIT message will be showed, if you press enter you will exit to upper menu. All menus have
3 or 4 levels.
17
Main menu (Level 1)
Men
u
Usage
1
STATUS →Enter Status menu
2
MEASUREMENTS →Enter Measurements menu
3
ALARM LOGS →Enter Alarm logs menu
4
INFORMATION →Enter Information menu
5
OPTIONS →Enter Options menu
6
COMMAND →Enter Command menu
7
TIME →Enter Time menu
8
SERVİCE →Enter Service menu
9
PASSWORD →Enter Password screen
10
ADJUST →Enter Adjust menu
Goto 1
Sub menus (Level 2)
Level
1
Level 2
Page
Level 3
STATUS Status of the UPS
MEASUREMENTS INPUT Input measurements
BYPASS Bypass measurements
INVERTER Inverter measurements
OUTPUT Output measurements
DC DC measurements
GENERAL General measurements
ENTER - EXIT
ALARM LOGS
UPS LOG RECORD Page1
ENTER CLEAR LOG Page1
ENTER - EXIT
INFORMATION RS232 Comm 1:-- 2:-- Page1
Maximum UPS power Page1
Nominal voltage and frequency Page1
Inverter firmware version Page2
PFC firmware version Page2
Panel firmware version Page2
UPS Model Page3
Communication protocol Page3
Chassis nr Page3
ENTER - EXIT
OPTIONS LCD OPTIONS LCD panel options
COMM.OPTIONS Communication options
ALARM OPTIONS Alarm options
BYPASS OPTIONS Bypass options
ENTER - EXIT
COMMAND By-pass transfer Page1
Boost charge start Page1
Short battery test start Page1
Relay check Page2
Dialup modem programming Page2
Alarm sound ON/OFF Page3
Warning sound interval Page3
ENTER - EXIT
TIME Current time Page1
Current date Page1
Set hour Page2
Set minute Page2
Set day Page3

19
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
17
Main menu (Level 1)
Men
u
Usage
1
STATUS →Enter Status menu
2
MEASUREMENTS →Enter Measurements menu
3
ALARM LOGS →Enter Alarm logs menu
4
INFORMATION →Enter Information menu
5
OPTIONS →Enter Options menu
6
COMMAND →Enter Command menu
7
TIME →Enter Time menu
8
SERVİCE →Enter Service menu
9
PASSWORD →Enter Password screen
10
ADJUST →Enter Adjust menu
Goto 1
Sub menus (Level 2)
Level
1
Level 2
Page
Level 3
STATUS Status of the UPS
MEASUREMENTS INPUT Input measurements
BYPASS Bypass measurements
INVERTER Inverter measurements
OUTPUT Output measurements
DC DC measurements
GENERAL General measurements
ENTER - EXIT
ALARM LOGS
UPS LOG RECORD Page1
ENTER CLEAR LOG Page1
ENTER - EXIT
INFORMATION RS232 Comm 1:-- 2:-- Page1
Maximum UPS power Page1
Nominal voltage and frequency Page1
Inverter firmware version Page2
PFC firmware version Page2
Panel firmware version Page2
UPS Model Page3
Communication protocol Page3
Chassis nr Page3
ENTER - EXIT
OPTIONS LCD OPTIONS LCD panel options
COMM.OPTIONS Communication options
ALARM OPTIONS Alarm options
BYPASS OPTIONS Bypass options
ENTER - EXIT
COMMAND By-pass transfer Page1
Boost charge start Page1
Short battery test start Page1
Relay check Page2
Dialup modem programming Page2
Alarm sound ON/OFF Page3
Warning sound interval Page3
ENTER - EXIT
TIME Current time Page1
Current date Page1
Set hour Page2
Set minute Page2
Set day Page3

20 www.tescom-ups.gr
USER MANUAL DS 300H Series �3/3 �30 kVA �UPS CONTROLLED UPS
18
Level 1
Level 2
Page
Level 3
Set month Page3
Set year Page3
Update time and date Page4
ENTER - EXIT
SERVİCE Operating hourmeter Page1
Maximum load Page1
ENTER Fault reset Page1
Fan maintenance hourmeter Page2
Batt.maintenance hourmeter Page2
General maintenance hourmeter Page2
Logout command Page3
ENTER - EXIT
PASSWORD
Getting service code Page1
Type service password Page1
Type user password Page1
ENTER - EXIT
ADJUST
(in English) Group adjustments Automatic settings
Inverter factory options Options list
Rectifier factory options Options list
Panel adjustments Options list
AC input adjustments AC input settings
AC Bypass adjustments AC bypass settings
AC output adjustments AC output settings
DC adjustments DC settings
Power adjustments Power settings
ENTER - EXIT
19
3.2.1 MEASUREMENTS menu
All mesasured values of the UPS can be monitored from this menu.
Use up and down buttons to move on submenu
MEASUREMENTS / INPUT (Level 2)
All rectifier input measurements are located in this menu, use up and down buttons to move on submenu
MEASUREMENTS
/
INPUT
Page 1 (Level 3)
P-N L1 L2 L3 Page header
Vinp: 221/222/223 V Phase to neutral measured AC input voltages
Iinp: 000/000/000 A Measured RMS AC input phase currents
…………………………….. Current alarm messages
Up previous page ,down next page
MEASUREMENTS
/
INPUT
Page 2 (Level 3)
P-P L13 L21 L32 Page header
Vinp: 381/382/383 V Phase to phase measured AC input voltages
Finp: 49.6 Hz Measured rectifier input frequency
…………………………….. Current alarm messages
Up previous page ,down next page
MEASUREMENTS
/
INPUT
Page 3 (Level 3)
ENTER - EXIT ENTER exit to upper menu
…………………………….. Current alarm messages
Up previous page, down next page
MEASUREMENTS / BYPASS (Level 2)
All by-pass input measurements are located in this menu, use up and down buttons to move on submenu
MEASUREMENTS
/
BYPASS
Page 1 (Level 3)
P-N L1 L2 L3 Page header
Vbyp: 221/222/223 V Phase to neutral measured AC bypass input voltages
OK OK -- Bypass voltage status
…………………………….. Current alarm messages
Up previous page, down next page
MEASUREMENTS
/
BYPASS
Page 2(Level 3)
P-P L13 L21 L32 Page header
Vbyp: 381/382/383 V Phase to phase measured AC bypass input voltages
Fbyp: OK / 50.0 Hz Measured bypass input frequency
…………………………….. Current alarm messages
Up previous page, down next page
MEASUREMENTS
/
BYPASS
Page 3(Level 3)
ENTER - EXIT ENTER exit to upper menu
…………………………….. Current alarm messages
Up previous page, down next page