Texas Instruments ADS8380EVM User manual

User's GuideSLAU146 – December 2004
ADS8380EVM
This user's guide describes the characteristics, operation, and use of the ADS838018-bit, 600-kHz, high-speed, serial interface analog-to-digital converter evaluationboard (EVM). A complete circuit description, schematic diagram, and bill of materialsare included.
The following related documents are available on the TI Web site at www.ti.com .
Data Sheets: Literature Numbers:ADS8380 SLAS387REF1004C-2.5 SBVS002SN74AHC1G125 SCLS377THS4031 SLOS224OPA132 SBOS054
Contents1 EVM Overview ............................................................................................................... 22 Analog Interface .............................................................................................................. 23 Digital Interface .............................................................................................................. 44 Power Supplies .............................................................................................................. 55 Using the EVM ............................................................................................................... 66 ADS8380EVM Bill Of Materials ............................................................................................ 78 Board Layers ................................................................................................................. 99 Schematics .................................................................................................................. 13
List of Figures
1 Input Buffer Circuit ........................................................................................................... 32 Top Layer ..................................................................................................................... 93 Power Plane ................................................................................................................ 104 Ground Plane ............................................................................................................... 115 Bottom Layer ................................................................................................................ 12
List of Tables
1 Analog Input Connector ..................................................................................................... 22 Jumper Setting ............................................................................................................... 43 Pinout for Serial Control Connector P2 ................................................................................... 54 Power Supply Test Points .................................................................................................. 55 Power Connector J2 Pinout ................................................................................................ 57 ADS8380EVM Bill of Materials ............................................................................................. 7
ADS8380EVMSLAU146 – December 2004 1

www.ti.com
1 EVM Overview
1.1 Features
2 Analog Interface
2.1 Signal Conditioning
EVM Overview
•Full-featured evaluation board for the ADS8380 18-bit, 600-kHz, single-channel, high-speedserial-interface analog-to-digital converter (ADC)•Onboard signal conditioning•Onboard reference•Input and output digital buffer
The ADS8380 analog-to-digital converter has both a positive and negative analog input pin. A signal forthe positive input pin can be applied at connector P1, pin 2 (shown in Table 1 ) or applied to the center pinof SMA connector J1. The EVM ships with the negative input pin shorted to ground close to the converterusing via SJP7. The negative and positive input pins have a range of -200 mV to +200 mV and -200 mVto VREF+200 mV, respectively.
Table 1. Analog Input Connector
Description Signal Name Connector Pin No. Signal Name Description
Inverting Input –IN P1.1 P1.2 +IN Noninverting InputReserved N/A P1.3 P1.4 N/A ReservedReserved N/A P1.5 P1.6 N/A ReservedReserved N/A P1.7 P1.8 N/A ReservedGround AGND P1.9 P1.10 N/A ReservedGround AGND P1.11 P1.12 N/A ReservedReserved N/A P1.13 P1.14 N/A ReservedGround AGND P1.15 P1.16 N/A ReservedGround AGND P1.17 P1.18 N/A ReservedReserved N/A P1.19 P1.20 REF+ External Reference Input
It is a recommended practice to buffer the analog input to any SAR-type converter with a high-speed,fast-settling, low-noise amplifier. The amplifier circuit shown in Figure 1 is the buffer circuit used on theADS8380EVM. This circuit consists of the THS4031, a high-speed, low-noise, low-distortion amplifierconfigured as an inverting gain of one. The circuit shown in Figure 1 was optimized to achieve the acspecifications (i.e., SNR, THD, SFDR, etc.) listed in the ADS8380 data sheet. The 12- Ωseries resistorworks with the capacitor to filter the input signal, but also isolates the amplifier from the capacitive load.The 6800-pF capacitor to ground at the input of the ADC works with the series resistor to filter the inputsignal, behaves like a charge reservoir, and provides a short to ground for high-frequency noise andkickback currents when the device switches from hold to sample mode. This external filter capacitor alsoworks with the amplifier to charge the internal sampling capacitor during sampling mode.
The type of input capacitors used in the signal path can make a few decibels of difference in acperformance. Polypropylene or C0G-type capacitors are recommended for the input signal path.Polypropylene capacitors cause the least distortion of the input signal and have excellent long-termstability, but are expensive and bulky. C0G ceramic capacitors cost less, come in smaller packages, andperform as well as polypropylene capacitors in many applications, but are not as stable over time andtemperature. The 68-pF and 6800-pF capacitors installed on the EVM are low-cost C0G type,manufactured by TDK Corporation.
ADS8380EVM 2 SLAU146 – December 2004

www.ti.com
_
+
THS4031
0.1 F
1 F
1 F
0.1 F
−VCC
+VCC
604 
604 
VIN
12 
6800 pF
1 F
100 
10 k
4.096 V
IN+
IN−
2.2 Reference Voltage
Analog Interface
Figure 1. Input Buffer Circuit
The ADS8380EVM allows the designer to select internal, onboard, or user-supplied reference-voltagesources. The internal reference is a 4.096-V reference voltage generated by the ADS8380 on pin 9. Theonboard reference can be either a REF3040 (U1) or REF1004-2.5 (U13). The EVM ships with theREF1004-2.5 installed. The reference amplifier, U3, is set for a gain of 1.6, enabling it to take a 2.5-Vinput and output 4.1 V for use with the converter, or as part of the dc offset voltage circuit for the inputbuffer (U4). The user-supplied reference voltage is applied to connector P1, pin 20 and can be routedthrough the reference buffer and filtered, if desired. The EVM allows a number of configurations. SeeTable 1 for jumper settings or the full schematic in Section 9 for more information. The common SOICfootprint of U13 allows users to evaluate this converter with various reference ICs.
The ADS8380EVM ships with the internal reference tied directly to the reference pin of the converter.
SLAU146 – December 2004 3ADS8380EVM

www.ti.com
3 Digital Interface
Digital Interface
Table 2. Jumper Setting
Reference Pins/PadsDescriptionDesignator
1-2 2-3
SJP1 Buffer onboard reference (REF1004-2.5) Shorted
(1)
OpenBuffer user-supplied reference voltage applied at P1 pin 20 Open ShortedSJP2 Connect external reference directly to SJP4 Shorted
(1)
OpenConnect buffered external reference to SJP4 Open ShortedSJP3 Connect U2 negative supply to ground Shorted OpenConnect U2 negative supply to –VCC Open Shorted
(1)
SJP4 Connect internal reference to REFIN Shorted
(1)
OpenConnect external reference to REFIN Open ShortedSJP5 Connect U4 negative supply to ground Shorted OpenConnect U4 negative supply to –VCC Open Shorted
(1)
SJP6 Connect DC offset voltage to U4 Shorted
(1)
N/ASJP7 Connect -IN pin to analog ground Shorted
(1)
N/AW1 Connect +5VD to BVDD Shorted
(1)
OpenConnect +3.3VD to BVDD Open ShortedW2 Set signal straight binary/2s complement ( SB/2C) high Shorted N/AW3 Set power down signal (PD) high Shorted N/AW4 Set frame sync signal (FS) high Shorted N/AW5 Set chip select signal ( CS) low Shorted N/A
(1)
Factory Installed
The ADS8380EVM is designed for easy interfacing to multiple platforms. Samtec plug and socketconnectors provide a convenient dual row header/socket combination at P1 and P2 to plug into prototypeboards or through ribbon cable to user system boards.
The digital input and output signals for the converter is available at connector P2 on the ADS8380EVM;see Table 3 for the connector pinout.
4 SLAU146 – December 2004ADS8380EVM

www.ti.com
4 Power Supplies
Power Supplies
Table 3. Pinout for Serial Control Connector P2
Description Signal Name Connector Pin Signal Name Description
Chip Select CS P2.1 P2.2 SB/2C Straight binary or 2s complement outputSerial Clock SCLK P2.3 P2.4 DGND GroundReserved N/A P2.5 P2.6 N/A ReservedFrame Sync FS P2.7 P2.8 N/A ReservedReserved N/A P2.9 P2.10 N/A ReservedReserved N/A P2.11 P2.12 N/A ReservedSerial Data Out SDO P2.13 P2.14 N/A ReservedBUSY BUSY P2.15 P2.16 N/A ReservedConvert Start CONVST P2.17 P2.18 DGND GroundPower down PD P2.19 P2.20 N/A Reserved
The EVM accepts four power supplies:•A dual ±Vs dc supply for the dual-supply operational amplifiers. The maximum recommended voltageis ±12 Vdc.•A single +5-Vdc supply for the analog section of the board (A/D + Reference).•A single +5-Vdc or +3.3-Vdc supply for the digital section of the board (A/D + buffers).
There are two ways to provide these voltages. The first way is to connect the voltages to the test pointslisted in Table 4 .
Table 4. Power Supply Test Points
Test Point Signal Description
TP1 +VA Connect +12-Vdc supply for amplifierTP2 –VA Connect –12-Vdc supply for amplifierTP3 +BVDD Apply +3.3 Vdc or +5 Vdc. See ADC data sheet for full range.TP4 +AVCC Apply +5 Vdc
The second way is to use the power connector J2 and derive the voltages elsewhere. Table 5 gives thepinout for J2. If using this connector, set W1 jumper to connect +3.3VD or +5VD from J2 to +BVDD. Shuntpins 1-2 to select +5VD, or pins 2-3 to select +3.3VD as the source for the digital buffer voltage supply(+BVDD).
Table 5. Power Connector J2 Pinout
Signal J2 Pin Signal
+VA(+12V) 1 2 –VA(–12 V)+5VA 3 4 N/CDGND 5 6 AGNDN/C 7 8 N/C+3.3VD 9 10 +5VD
ADS8380EVMSLAU146 – December 2004 5

www.ti.com
5 Using the EVM
5.1 Reference Design
5.2 Prototype Board
5.3 Software Test Platform
Using the EVM
The ADS8380EVM serves three functions:1. As a reference design2. As a prototype board3. As a software test platform
As a reference design, the ADS8380EVM contains the essential circuitry to showcase the analog-to-digitalconverter. This essential circuitry includes the input amplifier, reference circuit, and buffers. The EVManalog-input circuit is optimized for a 100-kHz input signal; therefore, users may need to adjust theresistor and capacitor values to accommodate higher frequencies. In ac-type applications where signaldistortion is a concern, polypropylene or C0G-type capacitors are recommended for use in the signal path.
As a prototype board, the buffer circuit has resistor pads for configuring the input as either single-ended orfully differential input. The input circuit can be modified to accommodate user prototype needs, whether itbe evaluating another differential amplifier or limiting noise for best performance. The analog, power, anddigital connectors can be made to plug into a standard 0.1-in. breadboard or ribbon cables to interfacedirectly to FPGAs or processors.
As a software test platform, connectors P1 and P2 plug into the serial interface connectors of the 5-6KInterface Board. The 5-6K Interface Board plugs into the TMS320C5000 and TMS320C6000 Digital SignalProcessor starter kits (DSK). See the 5-6K Interface Board User’s Guide (SLAU104 ) for more information.
ADS8380EVM 6 SLAU146 – December 2004

www.ti.com
6 ADS8380EVM Bill Of Materials
ADS8380EVM Bill Of Materials
The following table contains a complete bill of materials for the ADS8380EVM. The schematic diagram isalso provided for reference. Contact the Product Information Center or email [email protected] forquestions regarding this EVM.
Table 7. ADS8380EVM Bill of Materials
Item Reference Manufacturer'sQTY Value Footprint Manufacturer DescriptionNo. Designator Part Number
1 1 49.9 ΩR1 805 Panasonic - ECG or ERJ-6ENF49R9V RES 49.9 Ω1/10W 1% 0805 SMDAlternate
2 1 1.2 k ΩR2 603 Yageo America or 9C06031A1201FKHFT RES 1.20 k Ω1/10 W 1% 0603 SMDAlternate
3 2 NI R4, R5 805 Not Installed Not Installed
4 3 0 ΩR6, R15, R30 603 Panasonic - ECG or Alter- ERJ-3GEY0R00V RES 0 Ω1/16 W 5% 0603 SMDnate
5 7 10 k ΩR7, R8, R9, 603 Panasonic - ECG or ERJ-3EKF1002V RES 10 K Ω1/16 W 1% 0603 SMDR10, R11, AlternateR12, R32
6 1 10 k ΩR13 BOURNS Bourns 3214W-1-103E TRIMPOT 10 K Ω4MM TOP ADJ SMD_32X4W
7 1 768 ΩR14 603 Panasonic - ECG or ERJ-3EKF7680V RES 768 Ω1/16 W 1% 0603 SMDAlternate
8 2 0 ΩR16, R17 805 Panasonic - ECG or ERJ-6GEY0R00V RES 0 Ω1/10 W 5% 0805 SMDAlternate
9 2 604 ΩR18, R19 805 Panasonic - ECG or ERJ-6ENF6040V RES 604 Ω1/10 W 1% 0805 SMDAlternate
10 1 100 ΩR20 805 Panasonic - ECG or ERJ-6ENF1000V RES 100 Ω1/10 W 1% 0805 SMDAlternate
11 1 12 ΩR21 805 Panasonic - ECG or ERJ-6GEYJ120V RES 12 Ω1/8 W 5% 0805 SMDAlternate
12 8 100 R22, R23, 603 Panasonic - ECG or ERJ-3EKF1000V RES 100 Ω1/16 W 1% 0603 SMDR24, R25, AlternateR26, R27,R28, R29
13 1 1 k ΩR31 603 Panasonic - ECG or ERJ-3EKF1001V RES 1 k Ω1/16 W 1% 0603 SMDAlternate
14 1 49.9 k ΩR33 805 Panasonic - ECG or ERJ-6ENF4992V RES 49.9 k Ω1/10 W 1% 0805 SMDAlternate
15 1 47 µF C1 1206 TDK Corporation or C3216X5R0J476M CAP CER 47 µF 6.3 V X5R 20% 1206Alternate
16 5 1 µF C2, C3, C4, 805 TDK Corporation or C2012X7R1E105K CAP CER 1 µF 25 V X7R 0805 T/RC5, C31 Alternate
17 8 NI C6, C7, C21, 603 Not Installed Not Installed Multilayer CeramicC23, C44,C45, C59, C60
18 4 0.1 µF C8, C9, C10, 805 TDK Corporation or C2012X7R1E104K CAP CER 0.1 µF 25 V X7R 10% 0805C11 Alternate
19 12 0.1 µF C12, C13, 603 TDK Corporation or C1608X7R1E104K CAP CER 0.1 µF 25 V X7R 10% 0603C16, C17, AlternateC18, C52,C53, C54,C55, C56,C57, C58
20 6 2.2 µF C14, C15, 603 TDK Corporation or C1608X5R1A225MT CAP CER 2.2 µF 6.3 V X5R 20% 0603C19, C20, AlternateC28, C50
21 3 NI C22, C32, R3 805 Not Installed Not Installed Multilayer Ceramic
22 1 10 µF C24 3528 Kemet or Alternate T491B106K016AS CAPACITOR TANT 10 µF 16 V 10% SMD
23 8 0.01 µF C25, C26, 603 TDK Corporation or C1608X7R1H103KT CAP CER 10000 pF 50 V X7R 10% 0603C27, C29, AlternateC30, C42,C43, C51
24 1 6800 µF C33 805 TDK Corporation or C2012C0G1H682J CAP CER 6800 pF 50 V C0G 5% 0805Alternate
25 4 10 µF C34, C35, 1206 TDK Corporation or C3216X5R1C106KT CAP CER 10 µF 16 V X5R 20% 1206C36, C37 Alternate
26 4 10 µF C38, C39, 6032 Pansonic - ECG or ECS-T1EC106R CAP 10 µF 25 V Tantalum TE SMDC40, C41 Alternate
27 5 1000 pF C46, C47, 603 TDK Corporation or C1608C0G1H102KT CAP CER 1000 pF 50 V C0G 0603 T/RC48, C49, C62 Alternate
ADS8380EVMSLAU146 – December 2004 7

www.ti.com
ADS8380EVM Bill Of Materials
Table 7. ADS8380EVM Bill of Materials (continued)Item Reference Manufacturer'sQTY Value Footprint Manufacturer DescriptionNo. Designator Part Number
28 1 1 µF C61 603 TDK Corporation or C1608X5R1A105KT CAP CER 1 µF 10 V X5R 10% 0603Alternate
29 4 MMZ2 L1, L2, L3, L4 805 TDK Corporation or MMZ2012R601A FERRITE CHIP 600 Ω500 mA 0805012R6
01A
30 1 NI U1 3-SOT-23 Not Installed Not Installed REF3040 SOT23-3 CMOS Voltage Refer-ence
31 1 OPA132 U2 8-SOP(D) Texas Instruments OPA132U High-Speed FET-Input Operational Amplifier
32 8 SN74X1G125 U3, U6, U7, 5-SOT(DBV) Texas Instruments SN74AHC1G125DBVR Single Bus Buffer Gate/Line Driver withU8, U9, U10, 3-State OutputU11, U12
33 1 THS4031 U4 8-SOT(D) Texas Instruments THS4031CD 100-MHz Low-Noise High-Speed Amplifier
34 1 ADS8380 U5 28-PQFP Texas Instruments ADS8380IBRHPT 18-Bit 600 kSPS Serial Analog-to-Digital(QFN) Converter
35 1 REF1004-2.5 U13 8-SOP(D) Texas Instruments REF1004C-2.5 2.5-V Micropower Voltage Reference
36 1 SMA_PCB_ J1 SMA_JACK Johnson Components Inc. 142-0701-301 Right Angle SMA ConnectorMT
37 1 Power Supply J2 5X2X.1_ Samtec SSW-105-22-S-D 0.025-In. SMT Socket - Bottom Side of PWBSMT_Socket -VS
38 1 Samtec TSM-105-01-T-D-V 0.025-In. SMT Plug - Top Side of PWB-P
39 2 10X2X.1 P1, P2 10X2X.1 Samtec SSW-110-22-S-D-VS 0.025-In. SMT Socket - Bottom Side of PWB_SMT_P
LUG_&_
SOCKET
40 2 Samtec TSM-110-01-T-D-V-P 0.025-In. SMT Plug - Top Side of PWB
41 1 3POS_ W1 3pos_jump Samtec TSW-103-07-L-S 3-Position Jumper_0.1-In. SpacingJUMPER
42 4 2POS_ W2, W3, W4, 2pos_jump Samtec TSW-102-07-L-S 2-Position Jumper_0.1-In. SpacingJUMPER W5
43 2 SJP2 SJP6, SJP7 SJP2 Not Installed Not Installed Pad 2 Position Jumper
44 5 SJP3 SJP1, SJP2, SJP3 Not Installed Not Installed Pad 3 Position JumperSJP3, SJP4,SJP5
45 10 TP_.025 TP1, TP2, test_point2 Keystone Electronics 5000K-ND Test Point PC Mini 0.040-In. D RedTP3, TP4,TP5, TP6,TP7, TP8,TP10, TP13,
46 4 TP_0.25 TP9, TP11, test_point2 Keystone Electronics 5001K-ND Test Point PC Mini 0.040-In D BlackTP12, TP14
ADS8380EVM 8 SLAU146 – December 2004

www.ti.com
8 Board Layers
Board Layers
Figure 2. Top Layer
ADS8380EVMSLAU146 – December 2004 9

www.ti.com
Board Layers
Figure 3. Power Plane
ADS8380EVM 10 SLAU146 – December 2004

www.ti.com
Board Layers
Figure 4. Ground Plane
ADS8380EVMSLAU146 – December 2004 11

www.ti.com
Board Layers
Figure 5. Bottom Layer
ADS8380EVM 12 SLAU146 – December 2004

www.ti.com
9 Schematics
Schematics
Schematic diagrams are appended following this page.
ADS8380EVMSLAU146 – December 2004 13

123456
A
B
C
D
6
54321
D
C
B
Ati
12500 TI Boulevard. Dallas, Texas 75243
TITLE:
SHEET: OF:
FILE: SIZE:
REV:
Drawn By:
Engineer:
Revision History
REV ECN Number Approved
DOCUMENT CONTROL #:
12
BlockDiagram.sch
A
DATE: 30-Jun-2005
ADS8370EVM/ADS8380EVM
6458769
Serial Control
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
P2
Analog Input
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
P1
+VA
-VA
CS
FS
PD
SCLK
+AVCC
+VA
-VA
+BVDD
B_SDO
+IN
EXT_REF
B_BUSY
CONVST
SB/2C
Circuits
J1
+AVCC
+BVDD
Lijoy Philipose
Lijoy Philipose
1 2
3 4
5 6
7 8
910
J2
Power Supply
+VA -VA
+5VD
AGND
+AVCC
TP4
TP3
TP1
TP2
DGND
W1
+3.3VD
CS
SCLK
FS
B_SDO
PD
CONVST
B_BUSY

1 2 3 4 5 6
A
B
C
D
6
54321
D
C
B
Ati
12500 TI Boulevard. Dallas, Texas 75243
TITLE:
SHEET: OF:
FILE: SIZE:
REV:
Drawn By:
Engineer:
Revision History
REV ECN Number Approved
DOCUMENT CONTROL #:
22
Circuits
A
DATE: 30-Jun-2005
Circuits
6458769
C25
0.01uF
C17
0.1uF
C28
2.2uF
C18
0.1uF
C19
2.2uF
C29
0.01uF
C20
2.2uF
C30
0.01uF
+5VCC
+5VCC
+5VCC
C14
2.2uF
C26
0.01uF
+5VCC
C15
2.2uF
C27
0.01uF
+VBD
-VCC
+VCC
C11
0.1uF
C5
1uF
C3
1uF C9
0.1uF
R19
604
R21
12
+IN
C32
NI
C31
1uF
R3
NI
EXT_REF
R20
100
R5
NI
TP6
31
2
SJP4
1 2
SJP7
R18
604
+
C24
10uF
C33
6800pF
C1
47uF
R14
768
R6
0
C21
NI
+VCC
C2
1uF C8 0.1uF
-VCC
C10
0.1uF
C4
1uF
IN
1
OUT
2GND 3
U1
NI
+5VCC
R2
1.2k
3 1
2
SJP2
3 1
2
SJP1
R15
0
Lijoy Philipose
Lijoy Philipose
C22
NI
1
2
3
R13
10k
12
SJP6
3
26
74
5
1
U2
OPA132
R1
49.9
31
2
SJP5
31
2
SJP3
*
*
*
3
26
74
5 18
U4
THS4031
C23
NI
*
TP5
R17
0
R4
NI
R16
0
CS
SCLK
FS
PD
B_SDO
+VBD
C16
0.1uF
CS
SCLK
FS
R8
10k
R10
10k
R11
10k
+VBD
R12
10k
PD
L1
MMZ2012R601A
+C38
10uF
L2
MMZ2012R601A
+C39
10uF
TP10 +5VCC
C43
0.01uF
C13
0.1uF
TP11
TP8 +VBD
C42
0.01uF
C12
0.1uF
TP9
C35
10uF
C34
10uF
C46
1nF
C47
1nF
+AVCC
+BVDD
L3
MMZ2012R601A
L4
MMZ2012R601A
+C41
10uF
+C40
10uF
C6
NI
C7
NI
C44
NI
C45
NI
TP7
TP13
TP14
+VCC
-VCC
C36
10uF
C37
10uF
C48
1000pF
C49
1000pF
+VA
-VA
TP12
SB/2C 1 AGND 2
+VA 3
AGND 4 AGND 5
VA 6
REFM 7
REFIN
8
REFOUT
9
NC
10
IN+
11
IN-
12
NC
13
VA
14
AGND
15
VA
16
VA
17
AGND
18
AGND
19
BVDD
20
BGND
21
BUSY 22
SDO 23
SCLK 24
CONVST 25
CS 26
FS 27
PD 28
U5
ADS8370/ADS8380
SB/2C
CONVST
SDO
BUSY
B_BUSY
SB/2C
CONVST
B_SB/2C
B_PD
B_FS
B_CS
B_CONVST
B_SCLK
R7
10k
R9
10k
W2 W3 W4
W5
C50
2.2uF
C51
0.01uF
+5VCC
R30 0
R31 1k
R22
100
R23 100
R24 100
R25 100
R26 100 R27 100
R28
100
R29
100
C59 NI
C60 NI R32
10k
+VBD
+VBD C57
0.1uF
+VBD
C52
0.1uF
OE 1
A2
GND 3 Y
4
VCC
5U3
SN74X1G125
OE 1
A2
GND 3 Y
4
VCC
5U6
SN74X1G125
OE 1
A2
GND 3 Y
4
VCC
5U8
SN74X1G125
OE 1
A2
GND 3 Y
4
VCC
5U7
SN74X1G125
C53
0.1uF
OE 1
A2
GND 3 Y
4
VCC
5U9
SN74X1G125
OE 1
A2
GND 3 Y
4
VCC
5U10
SN74X1G125
OE
1
A
2
GND
3Y4
VCC 5
U11
SN74X1G125
OE
1
A
2
GND
3Y4
VCC 5
U12
SN74X1G125
+VBD
C54
0.1uF
+VBD
C55
0.1uF
+VBD
C56
0.1uF
+VBD
+VBD C58
0.1uF
NC
1
+VIN
2
EN
3
GND
4NC 5
VREF 6
NC 7
NC 8
U13
REF1004-2.5
+5VCC
C62
1000pF
C61
1uF
R33
49.9k
+5VCC

IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audio
Data Converters dataconverter.ti.com Automotive www.ti.com/automotive
DSP dsp.ti.com Broadband www.ti.com/broadband
Interface interface.ti.com Digital Control www.ti.com/digitalcontrol
Logic logic.ti.com Military www.ti.com/military
Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork
Microcontrollers microcontroller.ti.com Security www.ti.com/security
Telephony www.ti.com/telephony
Video & Imaging www.ti.com/video
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2004, Texas Instruments Incorporated