Texas Instruments LP875761Q1EVM User manual

User’s Guide
The LP875761Q1EVM Evaluation Module
ABSTRACT
This user’s guide describes the operation of the BMC043 evaluation module for the LP875761-Q1 multi-phase 4-
core step-down converter from Texas Instruments (TI). The LP875761-Q1 is intended to be used in 4-phase
output configuration (see Table 2-1). The user’s guide also provides design information including the schematic
and bill of materials (BOM).
Warning Warning Hot surface.
Contact may cause burns.
Do not touch!
Table of Contents
1 Trademarks..............................................................................................................................................................................2
2 Overview..................................................................................................................................................................................3
3 Quick Setup Guide..................................................................................................................................................................3
3.1 Installing/Opening the Software......................................................................................................................................... 4
3.2 Power Supply Setup...........................................................................................................................................................7
3.3 Notes on Efficiency Measurement Procedure..................................................................................................................10
4 GUI Overview........................................................................................................................................................................ 10
4.1 Main Tab...........................................................................................................................................................................10
4.2 Other Tabs and Menus..................................................................................................................................................... 11
4.3 Console............................................................................................................................................................................ 17
5 Bill of Materials..................................................................................................................................................................... 19
6 Board Layout.........................................................................................................................................................................21
7 LP875761Q1EVM Schematics..............................................................................................................................................29
8 Revision History................................................................................................................................................................... 30
List of Figures
Figure 2-1. LP875761Q1EVM..................................................................................................................................................... 3
Figure 3-1. LP8757 Installer License Agreement........................................................................................................................ 4
Figure 3-2. Features of LP8757 Installation.................................................................................................................................5
Figure 3-3. LP8757 Destination Folder........................................................................................................................................5
Figure 3-4. LP8757 Installation Complete................................................................................................................................... 6
Figure 3-5. Evaluation Software Graphical User Interface (GUI) When Board Connected......................................................... 6
Figure 3-6. Assert nRST.............................................................................................................................................................. 7
Figure 3-7. Read Registers Buttons............................................................................................................................................ 8
Figure 3-8. BUCK0 Enabled........................................................................................................................................................ 8
Figure 3-9. Assert EN1................................................................................................................................................................ 9
Figure 4-1. Accessing Direct Register Write..............................................................................................................................12
Figure 4-2. Direct Register Access View................................................................................................................................... 13
Figure 4-3. Selecting Register Values........................................................................................................................................14
Figure 4-4. Register Update Mode............................................................................................................................................ 15
Figure 4-5. Config Tab of the LP8757 GUI................................................................................................................................ 16
Figure 4-6. Advanced Tab of LP8757 GUI.................................................................................................................................16
Figure 4-7. Opening Console.....................................................................................................................................................17
Figure 4-8. Example of Command Use in Console................................................................................................................... 18
Figure 6-1. Board Stack-Up....................................................................................................................................................... 21
Figure 6-2. Top View of the LP875761-Q1EVM.........................................................................................................................22
www.ti.com Table of Contents
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 1
Copyright © 2020 Texas Instruments Incorporated

Figure 6-3. Component Placement Top Layer........................................................................................................................... 23
Figure 6-4. Component Placement Bottom Layer..................................................................................................................... 24
Figure 7-1. LP875761Q1EVM Schematic..................................................................................................................................29
List of Tables
Table 2-1. LP875761Q1 Configurations.......................................................................................................................................3
Table 4-1. Mode Information...................................................................................................................................................... 11
Table 4-2. I2C-Compatible Bus Support.....................................................................................................................................11
Table 4-3. Console Macros........................................................................................................................................................ 18
Table 5-1. Bill of Materials for LP875761Q1EVM...................................................................................................................... 19
1 Trademarks
Microsoft Windows XP® is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
Trademarks www.ti.com
2The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

2 Overview
The LP875761Q1EVM customer evaluation module demonstrates the integrated circuit LP875761-Q1 from TI.
The LP875761-Q1 is a high-performance, multi-phase step-down converter designed to meet the power
management requirements of the latest applications processors and platform needs in automotive infotainment
and cluster applications and also in automotive camera power applications. The device contains four step-down
converter cores, which are bundled together as one single 4-phase buck converter. This document covers user
software provided with the EVM and design documentation that includes schematics and parts list.
Table 2-1. LP875761Q1 Configurations
PART NUMBER OUTPUT CONFIGURATION NUMBER OF OUTPUTS EVM NUMBER
LP875761-Q1 4-phase 1 LP875761Q1EVM
Figure 2-1. LP875761Q1EVM
3 Quick Setup Guide
Many of the components on the LP875761Q1EVM are susceptible to damage by electrostatic discharge (ESD).
Customers are advised to observe proper ESD handling precautions when unpacking and handling the EVM,
including the use of a grounded wrist strap at an approved ESD workstation.
Upon opening the LP875761Q1EVM package, ensure that the following items are included:
• LP875761Q1EVM Evaluation Board
• USB Cable
If any of the items are missing, contact the closest Texas Instruments Product Information Center to inquire
about a replacement.
www.ti.com Overview
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 3
Copyright © 2020 Texas Instruments Incorporated

3.1 Installing/Opening the Software
The EVM software is controlled through a graphical user interface (GUI). The software communicates with the
EVM through an available USB port. The minimum hardware requirements for the EVM software are:
• IBM PC-compatible computer running a Microsoft Windows XP® or newer operating system
• Available USB port
• Mouse
Software installation
1. Open the LP8757_installer.exe.
2. Installer prompts to accept the license agreement (see Figure 3-1).
3. Installer prompts to choose which features of LP8757 Installer you want to install (see Figure 3-2).
4. Installer prompts to select Destination Folder (see Figure 3-3).
5. Press Install and the installation starts.
6. Installer prompts when installation is complete (see Figure 3-4).
Open the LP8757 GUI. Connect the EVM to the PC with the USB cable.
1. With the power supply disconnected from the unit under test (UUT), open LP8757.exe located in the directory
selected during installation.
2. On the Evaluation SW window bottom right corner you should see text Hardware connected. Refer to Figure
3-5.
Figure 3-1. LP8757 Installer License Agreement
Quick Setup Guide www.ti.com
4The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

Figure 3-2. Features of LP8757 Installation
Figure 3-3. LP8757 Destination Folder
www.ti.com Quick Setup Guide
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 5
Copyright © 2020 Texas Instruments Incorporated

Figure 3-4. LP8757 Installation Complete
Figure 3-5. Evaluation Software Graphical User Interface (GUI) When Board Connected
Quick Setup Guide www.ti.com
6The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

3.2 Power Supply Setup
To power up the EVM, one power supply is needed. For full-load testing of the LP875761Q1EVM, a DC-power
supply capable of at least 10 A and 5 V is required. 5 A is suggested as a practical minimum for partial load. The
power supply is connected to the EVM using connector J4. The power supply and cabling must present low
impedance to the UUT; the length of power supply cables must be minimized. Remote sense, using connector
J8, can be used to compensate for voltage drop in the cabling.
With the power supply disconnected from the UUT, set the supply to 3.3 V or 5.0 V DC and the current limit to 5
A minimum. Set the power supply output OFF. Connect the power supply's positive terminal (+) to VIN and
negative terminal (–) to GND on UUT (J4 power-in terminal block). Check that jumpers on the boards are set as
shown in Figure 2-1 (factory default jumper configuration).
Set power supply output ON, and then continue with the following steps. Note that following steps are only an
example. Register values, enable control, mode and multiphase status may differ depending on the
LP875761Q1EVM configuration.
1. On Evaluation software GUI, click on Assert NRST (see Figure 3-6).
2. Click on either of the two Read Registers buttons. You should see ready message on green background next
to the Read Registers button (see Figure 3-7).
3. Check that Buck0 is enabled, checkbox is ticked (see Figure 3-8).
4. Click on Assert EN1 (see Figure 3-9).
5. Click on either of the two Read Registers buttons.
6. In this example case the GUI indicates Disabled under Mode until EN1 is asserted. After EN1 is asserted
Mode is changed to Enabled. In case BUCKx is enabled or disabled with bit instead of ENx pin, the Mode can
be checked by reading registers. GUI indicates also Master under Multiphase status of Buck 0. Mode of other
bucks are Disabled and Multiphase status is Slave to Buck0. The EVM is now ready for testing with default
register settings loaded.
Figure 3-6. Assert nRST
www.ti.com Quick Setup Guide
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 7
Copyright © 2020 Texas Instruments Incorporated

Figure 3-7. Read Registers Buttons
Figure 3-8. BUCK0 Enabled
Quick Setup Guide www.ti.com
8The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

Figure 3-9. Assert EN1
www.ti.com Quick Setup Guide
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 9
Copyright © 2020 Texas Instruments Incorporated

3.3 Notes on Efficiency Measurement Procedure
Output Connections: An appropriate electronic load or high-power system source meter instrument, specified for
operation down to 500 mV, is desirable for loading the UUT. The maximum load current is specified as 4 A per
phase. Be sure to choose the correct wire size when attaching the electronic load. A wire resistance that is too
high will cause a voltage drop in the power distribution path which becomes significant compared to the absolute
value of the output voltage. Connect an electric load to J13. It is advised that, prior to connecting the load, it be
set to sink 0 A to avoid power surges or possible shocks.
Voltage drop across the PCB traces will yield inaccurate efficiency measurements. For the most accurate voltage
measurement at the EVM, use J6 (unpopulated through-hole) to measure the input voltage and J1 (unpopulated
through-hole) to measure the output voltage.
To measure the current flowing to/from the UUT, use the current meter of the DC power supply/electric load as
long as it is accurate. Some power source ammeters may show offset of several milliamps and thus will yield
inaccurate efficiency measurements. In order to perform very accurate Iq measurements on the UUT, disconnect
input protective Zener diode D1 by removing the shunt J5 from the board. When connected, this diode will cause
some leakage, especially on high VIN voltages.
4 GUI Overview
The evaluation software has the following tabs: Main, Config, and Advanced. The three tabs together provide the
user access to the whole register map of the LP875761-Q1. Additional register control can be obtained from
Tools --> Direct Register Access.
4.1 Main Tab
The Main tab (see for example Figure 3-9) has the elemental controls for the EVM and provides a view to the
chip status. Starting from top, the main controls are:
• I2C mode or 4 Enable mode. If this states I2C mode, device is controlled with I2C. When this states 4EN
mode, bucks are controlled with ENx pins.
• Assert NRST: This checkbox will assert high level to LP875761-Q1 NRST pin. This pin enables the chip
internal voltage reference and bias circuitry.
• Assert EN1: This checkbox will assert high level to LP875761-Q1 EN1 pin. Asserting EN1 may enable the
buck regulator(s) or switch to different output voltage level, depending on the register settings.
• Assert EN2: This checkbox will assert high level to LP875761-Q1 EN2 pin. Asserting EN2 may enable the
buck regulator(s) or switch to different output voltage level, depending on the register settings.
• Assert EN3: This checkbox will assert high level to LP875761-Q1 EN3 pin. Asserting EN3 may enable the
buck regulator(s) or switch to different output voltage level, depending on the register settings.
• Assert EN4: In 4 Enable mode, this checkbox will assert high level to LP875761-Q1 SCL pin, (alternative
function is EN4). Asserting EN4 may enable one or more of the buck regulators, depending on the register
settings. This checkbox is visible only when device is configured to 4 Enable Signal Mode.
• Assert SW Reset: To perform a complete SW reset to the chip, assert this checkbox. See the LP875761-Q1
datasheet for explanation of LP875761-Q1 reset scenarios.
Note
The recommended start-up sequence for LP875761Q1 is to first assert NRST, then write all needed
configuration bits by using the GUI, and then enable one or more of th buck regulators by ENx pin or
EN_BUCKx bit.
Quick Setup Guide www.ti.com
10 The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

The Bucks section provides status information and enable controls for all the 4 buck cores. On the left of the
section are the check-boxes for the buck enable bits. The Mode field provides information on each of the buck
core and can have any of the values given in Table 4-1:
Table 4-1. Mode Information
BUCK MODE
Disabled Buck state machine in 'disable'
Enabled Buck state machine in 'enable'
The Multiphase status info field tells whether a buck core is configured as a master or a slave. The "Current"
field gives the result of the buck converter load current measurement operation. Output currents of each buck
core and total output current of one or more of the masters are shown on the fields.
The System Flags / Interrupts section as well as the Interrupt bits and the Status bits sections give data on
system faults and warnings. If the interrupt is set for any reason the Interrupt active field shall show ‘1’ on red
background. The flag causing the interrupt will also be set on the Main tab. Interrupts on LP875761-Q1 can only
be cleared by writing '1’ to associated registers. Any individual flag can be cleared by clicking the Clear button
next to each flag field. Some of the flags also have a mask bits. If Mask check-box of certain flag is checked, the
interrupt is not generated. The Status bits will show the current status of the faults.
The Power Good section is for Power Good pin control and indication. It includes the latched values of buck
Power Good Faults. These can be cleared with the Clear -button.
At the bottom of the GUI window is the Auto Write checkbox. If Auto Write is checked (default) any checking, un-
checking or pulldown menu selections will immediately launch I2C writes to the chip register(s). If not checked,
the user can update the chip registers to correspond the configuration selected on the GUI by clicking Write
Registers.
If Poll Status is selected the software sends a query to the LP875761-Q1 at a fixed interval in order to detect the
status of the chip, including operation mode, multi-phase status, and output current. If also the Poll Only Pins is
selected the software is monitoring only the state of Interrupt and Powergood pins. If Poll Status is not selected
or if Poll Only Pins is selected, user can read the registers by applying Read Registers. Bus Speed pulldown
menu selections are given in Table 4-2 below and is instantly applied for System I2C.
Table 4-2. I2C-Compatible Bus Support
BUS SPEED SELECTION EXPLANATION
Fast (400 kHz) Fast I2C-compliant operation at 400 kHz
High-Speed (3.4 MHz) HS I2C-compliant data transfer with master codes.
4.2 Other Tabs and Menus
The Tools pulldown menu hosts another way of accessing the LP875761-Q1 registers (see Figure 4-1). The
Direct Register Access tool can be used to read or write any register (see Figure 4-2). Selecting a register, the
bits appear on the right side Field View (see Figure 4-3). When moving mouse over bits in Field View, bits are
highlighted in the register view. Bits can be controlled either from register view or field view. Register settings can
also be saved to a file or pre-made register file can be loaded in the Direct Register Access tool. Registers can
be updated immediately or manually (see Figure 4-4).
When using direct register access, TI recommends un-checking the poll status check-box. This way the GUI will
only do the reads and writes commanded from the direct access dialog.
www.ti.com GUI Overview
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 11
Copyright © 2020 Texas Instruments Incorporated

Figure 4-1. Accessing Direct Register Write
GUI Overview www.ti.com
12 The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

Figure 4-2. Direct Register Access View
www.ti.com GUI Overview
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 13
Copyright © 2020 Texas Instruments Incorporated

Figure 4-3. Selecting Register Values
GUI Overview www.ti.com
14 The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

Figure 4-4. Register Update Mode
The Configure and Advanced tabs provide the user with pulldown menus and check-boxes for the part of the
register space that is not covered by the Main tab, such as output voltage control. These controls are self-
explanatory. Refer to the LP875761-Q1 data sheet for explanation of the functions. See following images for
reference of the Config and Advanced tabs.
www.ti.com GUI Overview
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 15
Copyright © 2020 Texas Instruments Incorporated

Figure 4-5. Config Tab of the LP8757 GUI
Figure 4-6. Advanced Tab of LP8757 GUI
GUI Overview www.ti.com
16 The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

4.3 Console
To show or hide the console, toggle the option in the View pulldown menu (see Figure 4-7). The console can be
used to access the LP875761-Q1 registers. Registers can be read or written simply by referring to the logical
registers by their name. See an example Figure 4-8. The console has a number of integrated macros that are
listed in Table 4-3.
Figure 4-7. Opening Console
www.ti.com GUI Overview
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 17
Copyright © 2020 Texas Instruments Incorporated

Figure 4-8. Example of Command Use in Console
Table 4-3. Console Macros
Command Parameters Explanation
register_name = register value | - Write a value to writable I2C register or logical register. If no parameter given, will
return the current register value. The logical register names are the same as given in
the data sheet, and must be in uppercase.
Example read: BUCK_LOAD_CURRENT; example write: BUCK0_STARTUP _DELAY
= 10
wait (time) Wait for time given in ms. Useful in loops.
iout (buck number) Returns the measured load current of the chosen buck core.
0x address = data
or
address[bits] = data
I2C read or write command.
addr = value
examples:
0x12 = 0xaa
0x12[7] = 1
0x12[3:0] = 15
The console supports use of scripts. If a text file containing commands supported by the console is stored in the
same folder with the evaluation software executable, then the script can be launched from the console by typing
the text file name, like script.txt.
GUI Overview www.ti.com
18 The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated

5 Bill of Materials
Table 5-1 lists EVM bill of materials. This is for output configurations listed in Table 2-1. See Section 7 for these
configuration specific assembly details.
Note
The LP875761-Q1 I/O lines are connected to the microcontroller through 0-Ω resistors. These
resistors are assembled to match the default I/O configuration of the LP875761-Q1. If LP875761-Q1
ENx/GPIOx or PGOOD pins are configured as push-pull outputs, corresponding 0-Ω resistors (R25,
R27, R28, R29) must be removed to prevent possible damage to the microcontroller I/O pins. In open-
drain configuration the microcontroller internal pullups are enabled by the GUI and pullup resistors
R14 to R20 are not needed.
Table 5-1. Bill of Materials for LP875761Q1EVM
Designator Description Manufacturer Part Number Qty.
PCB Printed Circuit Board Any BMC043 1
C1, C2, C3, C4, C30, C31, C32,
C33, C34, C35, C38, C39, C40,
C41, C42, C43, C46, C47, C48,
C49, C50, C54, C55, C56, C57,
C58, C66, C67
CAP, CERM, 22 µF, 10 V, ± 10%, X7R,
AEC-Q200 Grade 1, 1206
MuRata GCM31CR71A226KE02 28
C5, C6, C7, C8, C15, C16, C19,
C20, C23, C24, C27, C28, C73,
C80, C82, C88, C90
CAP, CERM, 10 µF, 10 V, ± 10%, X7R,
AEC-Q200 Grade 1, 0805
MuRata GCM21BR71A106KE22L 17
C9, C17, C21, C25, C29, C36,
C44, C52, C60, C65, C72, C74,
C75, C76, C77, C78, C79, C81,
C83, C84, C85, C86, C89
CAP, CERM, 0.1 µF, 16 V,± 5%, X7R,
AEC-Q200 Grade 1, 0402
MuRata GCM155R71C104JA55D 23
C10, C11, C12, C13 CAP, CERM, 390 pF, 50 V,± 5%, C0G/
NP0, AEC-Q200 Grade 1, 0402
TDK CGA2B2C0G1H391J050BA 4
C14, C18, C22, C26, C37, C45,
C53, C61, C95
CAP, CERM, 0.01 µF, 50 V, ± 10%, C0G/
NP0, AEC-Q200 Grade 1, 0402
MuRata GCM155R71H103KA55D 9
C63 CAP, TA, 220 µF, 10 V, ± 10%, 0.15 Ω,
SMD
AVX TPSD227K010R0150 1
C64 CAP, CERM, 100 µF, 6.3 V, ± 20%, X5R,
0805
MuRata GRM21BR60J107M 1
C69, C70, C71, C87 CAP, CERM, 15 pF, 100 V,± 5%, C0G/
NP0, AEC-Q200 Grade 1, 0603
MuRata GCM1885C2A150JA16D 4
C91, C92, C93, C94 CAP, CERM, 1 µF, 25 V, ± 10%, X7R,
AEC-Q200 Grade 1, 0603
MuRata GCM188R71E105KA64D 4
D1 Diode, Zener, 5.6 V, 1 W, SMA Diodes Inc. SMAZ5V6-13-F 1
D2 Diode, Schottky, 30 V, 0.2 A, SOD-323 Diodes Inc. BAT42WS-7-F 1
H1, H2, H3, H4 Bumpon, Hemisphere, 0.375 X 0.235,
Black
3M SJ61A2 4
H5 CABLE MINI USB 5PIN 1M 2.0 VERS Assman WSW AK672M/2-1-R 1
J2 Header, 100 mil, 2x2, Tin, SMT Molex 15-91-2040 1
J3, J5, J8, J10, J11, J12, J14 Header, 2.54 mm, 2x1, Tin, SMT Harwin M20-8770246 7
J4, J13 Terminal Block, 2x1, 5 mm, Green, TH Phoenix Contact 1935776 2
J15 Connector, Receptacle, Mini-USB Type
B, R/A, Top Mount SMT
TE Connectivity 1734035-2 1
J16 Header, 100 mil, 3x1, Gold, SMT Samtec TSM-103-01-L-SV 1
L1, L2, L3, L4 Inductor, Shielded, 330 nH, 5.4 A, 0.017
Ω, AEC-Q200 Grade 1, SMD
MuRata Toko DFE252012PD-R33M 4
L5, L6, L7, L8 Ferrite Bead, 30 Ω at 100 MHz, 4 A, 0805 MuRata BLM21PG300SH1D 4
www.ti.com Bill of Materials
SNVU751 – OCTOBER 2020
Submit Document Feedback
The LP875761Q1EVM Evaluation Module 19
Copyright © 2020 Texas Instruments Incorporated

Table 5-1. Bill of Materials for LP875761Q1EVM (continued)
Designator Description Manufacturer Part Number Qty.
L9 Inductor, Wirewound, Ferrite, 10 µH, 0.12
A, 0.5 Ω, SMD
Taiyo Yuden LB2012T100KR 1
LBL1 Thermal Transfer Printable Labels,
1.250" W x 0.250" H - 10,000 per roll
Brady THT-13-457-10 1
R1, R2, R3, R4 RES, 3.9, 5%, 0.063 W, AEC-Q200
Grade 0, 0402
Vishay-Dale CRCW04023R90JNED 4
R5, R6, R7, R9, R10, R12, R21,
R22, R23, R24, R25, R27, R28,
R29
RES, 0, 5%, 0.063 W, 0402 Yageo America RC0402JR-070RL 14
R8 RES, 0.01, 1%, 3 W, 2512 Bourns CRA2512-FZ-R010ELF 1
R30 RES, 6.80 k, 1%, 0.1 W, 0603 Yageo America RC0603FR-076K8L 1
R31, R32 RES, 39.0, 1%, 0.1 W, 0603 Yageo America RC0603FR-0739RL 2
R33 RES, 68.0 k, 1%, 0.1 W, 0603 Yageo America RC0603FR-0768KL 1
R34 RES, 33.0 k, 1%, 0.1 W, 0603 Yageo America RC0603FR-0733KL 1
R35 RES, 1.00, 1%, 0.1 W, 0603 Yageo America RC0603FR-071RL 1
R36 RES, 470 k, 5%, 0.1 W, AEC-Q200
Grade 0, 0603
Vishay-Dale CRCW0603470KJNEA 1
R37, R38 RES, 1.00 k, 1%, 0.1 W, AEC-Q200
Grade 0, 0603
Vishay-Dale CRCW06031K00FKEA 2
SH-J1, SH-J2, SH-J3, SH-J4, SH-
J5
Shunt, 100 mil, Gold plated, Black TE Connectivity 881545-2 5
TP1, TP2, TP3, TP4, TP5, TP6,
TP7, TP8, TP9, TP10, TP11,
TP12, TP13, TP14
Test Point, Miniature, SMT Keystone 5015 14
U1 Four-Phase DC/DC Buck Converter,
RNF0026C (VQFN-HR-26)
Texas Instruments LP875761ARNFRQ1 1
U2 AT91SAM ARM-based Flash MCU,
LQFP100
Atmel ATSAM3U2CA-AU 1
U3 Dual Linear Regulator with 300 mA and
150 mA Outputs and Power-On-Reset,
10-pin LLP, Pb-Free
Texas Instruments LP3996SD-1833/NOPB 1
Y1 Crystal, 12 MHz, 12pF, SMD AVX CX5032GB12000H0PESZZ 1
C51, C59 CAP, CERM, 22 µF, 10 V, ± 10%, X7R,
AEC-Q200 Grade 1, 1206
MuRata GCM31CR71A226KE02 0
C62, C68 CAP, CERM, 0.1 µF, 16 V,± 5%, X7R,
AEC-Q200 Grade 1, 0402
MuRata GCM155R71C104JA55D 0
J1, J6 Header, 100 mil, 2x1, Gold, TH Samtec TSW-102-07-G-S 0
J7 Terminal Block, 8x1, 2.54 mm, TH Phoenix Contact 1725711 0
J9 Receptacle, 2.5 mm, 3x2, Gold, SMT TE Connectivity 6651712-1 0
R11, R13, R26 RES, 0, 5%, 0.063 W, 0402 Yageo America RC0402JR-070RL 0
R14, R15, R16, R17, R18, R19,
R20
RES, 1.8 k, 5%, 0.1 W, AEC-Q200 Grade
0, 0603
Vishay-Dale CRCW06031K80JNEA 0
Bill of Materials www.ti.com
20 The LP875761Q1EVM Evaluation Module SNVU751 – OCTOBER 2020
Submit Document Feedback
Copyright © 2020 Texas Instruments Incorporated