Texas Instruments TPA5051EVM User manual

1 Introduction
1.1 Description
User's GuideSLOU184 – July 2006
TPA5051EVM
Contents1 Introduction .......................................................................................... 12 Software ............................................................................................. 23 Operation ............................................................................................ 64 Reference ............................................................................................ 95 TPA5051EVM Schematic Diagram ............................................................. 12
List of Figures
1 TPA5051 in I
2
S Mode With Separate Delays for Left and Right Channels ................. 32 TPA5051 in I
2
S Mode With Frame Delay........................................................ 43 TPA5051 in Right-Justified Mode ................................................................ 54 TPA5051 in I
2
S Mode – Unable to Communicate .............................................. 65 Top Layer of the TPA5051EVM .................................................................. 76 Bottom Layer of the TPA5051EVM .............................................................. 87 TPA5051EVM Top Layer .......................................................................... 98 TPA5051EVM Second Layer ..................................................................... 99 TPA5051EVM Third Layer ....................................................................... 1010 TPA5051EVM Bottom Layer ..................................................................... 10
List of Tables
1 Bill of Materials .................................................................................... 11
The TPA5051 evaluation module (EVM) consists of a single TPA5051 audio delay device, along with otherexternal components mounted on a printed-circuit board (PCB) that can be used to independently delaytwo digital audio streams. Each digital audio stream consists of a left and right channel, both of which canbe delayed up to 4095 samples (with a 48-kHz sampling rate, that equates to more than 85ms of delay).
The TPA5051EVM is designed to work seamlessly with the TI Input USB board, but can function as astand-alone board for pass-through testing in any system. All that is required is an I
2
S audio source, anI
2
C controller, and a 5-V supply.
The TPA5051EVM also includes an onboard digital-to-analog controller (DAC), the PCM1606, which canconvert I
2
S or left-justified data to an analog out. The analog out is filtered on the board and can beviewed with a scope probe.
National Instruments is a trademark of National Instruments Corporation.
SLOU184 – July 2006 TPA5051EVM 1Submit Documentation Feedback

www.ti.com
1.2 TPA5051EVM Specifications
2 Software
2.1 Installation
2.2 Software Use
Software
+5 V Supply Voltage 5 V
I
DD
Supply current 150 mA maximumI
DD
(with TI Input USB board connected) Supply current 500 mA maximum
The included compact disk (CD) has all the software and drivers necessary to properly operate theTPA5051EVM with the TI Input USB board. This software is designed to work only with personalcomputers (PC). The installation software consists of TPA505x Interface SAA,Command Tool, and .NetFramework 1.1.
1. Open up the CD, and browse the directory named TPA505x HD GUI Installer.2. Click on setup.exe. The installer will then initialize.3. Next, the user must choose the directories in which to install the software. The default directory for theTPA505x Interface SAA software is C:\Program Files\Texas Instruments Inc\, and the default directoryfor the National Instruments™ files is C:\Program Files\National Instruments\. Other directories may beused, but for purposes of convenience, the default directories are recommended.4. Once the directory selection has been made, click next to proceed.5. The National Instruments™ License Agreement appears. It is necessary to read and accept thisagreement to continue with the installation.6. Once the National Instruments™ License Agreement has been accepted, another window indicatingwhich components are to be installed appears. It should read Adding or Changing - TPA505x InterfaceSAA Files. Click next to proceed.7. The TPA505x SAA Interface program then installs the necessary files.8. Once the TPA505x SAA Interface program has been installed, the setup program begins installingCommand Tool 6.0. The Command Tool License Agreement must be read and accepted forinstallation to continue.9. On acceptance of the Command Tool License Agreement, .Net Framework 1.1 is installed. Thisinstallation procedure may take a while. When it is finished, click ok.10. Command Tool 6.0 proceeds to configure the new software. When it is finished, click Finish.11. Power up the TI Input USB Board (see the Operation section in this document), and then connect theUSB cable from the computer to the TI Input USB Board. A message pops up stating that thecomputer has found new hardware. Shortly after that message appears, the computer finds and installsthe correct drivers for it.
The TPA5051 software graphical user interface (GUI) is designed to allow the user to control the TPA5051by an I
2
C bus.1. Select the I
2
C address of the EVM by entering the address number under the I2C Address (0-7)section. The default for the program is 0. The default for the EVM is also 0. The number in the programcorresponds to the last three digits of the I
2
C address of the device (ADD2, ADD1, and ADD0), whichcan be controlled by installing or removing jumpers J5, J4, or J3.2. Select the mode of operation by clicking on the appropriate circle under Stream Type.3. The right and left delays can be adjusted by turning the knob to the desired number of delay samples,or simply entering the number in the box provided (see Figure 1 ). The maximum number of delaysamples per channel for the TPA5051 is 4095. The TPA505x software, however, allows forprogramming up to 8191 samples per channel. This is because the software is designed to work forboth the TPA5050 and TPA5051. A delay set above 4095 samples is not valid for the TPA5051.4. The right and left delays can be tied together by clicking on the R Track L 1 OFF/ON box to the right ofthe Right Delay knob.
2TPA5051EVM SLOU184 – July 2006Submit Documentation Feedback

www.ti.com
Software
5. The delay also can be controlled with the Frame Delay option. Simply click on the Frame Delay Mode1 ON/OFF box, and the frame delay options become available. Frame delay mode affects both left andright channels simultaneously (see Figure 2 ).6. Clicking on the Right Justified mode under Stream Type brings up a hidden window, called PacketLength. Through this, the number of packet lengths to be delayed can be entered (see Figure 3 ).7. The option Bypass simply sets the TPA5051 to pass the data through, without doing any manipulationto it.8. The I2C Status display at the bottom right indicates whether the device and the computer arecommunicating properly. A red status bar indicates a problem. A green status bar indicates the deviceand computer are talking (see Figure 4 ). Possible solutions to the red status bar problem are todepress and release the reset button on the TI Input USB board, check to see that all cables areproperly connected, restart the TPA5051 GUI, remove and then re-insert the USB cable into thecomputer, reboot the computer, or re-install the software.9. The list of registers on the right side of the screen (0x01 …0x10) indicate what values were last writtento that particular register. The TPA5051 has eighteen registers, however the two Complete Updateregisters are not shown on the GUI. Therefore, only registers (0x01 …0x07) and (0x09 …0x0F) areshown.
10. The channel selection tab is designed for use with the TPA5051, which has two independent digitalaudio inputs. Selecting the Channel 1 tab allows control of the registers for digital audio input 1(DATA1 of the device). Selecting the Channel 2 tab allows control of the registers for digital audio input2 (DATA2 of the device). See Figure 2
Figure 1. TPA5051 in I
2
S Mode With Separate Delays for Left and Right Channels
SLOU184 – July 2006 TPA5051EVM 3Submit Documentation Feedback

www.ti.com
Software
Figure 2. TPA5051 in I
2
S Mode With Frame Delay
4TPA5051EVM SLOU184 – July 2006Submit Documentation Feedback

www.ti.com
Software
Figure 3. TPA5051 in Right-Justified Mode
SLOU184 – July 2006 TPA5051EVM 5Submit Documentation Feedback

www.ti.com
3 Operation
3.1 Quick Start List for Use With the TI Input USB Board
3.2 Power Supply
3.3 EVM Preparation
Operation
Figure 4. TPA5051 in I
2
S Mode – Unable to Communicate
Follow these steps to use the TPA5051EVM with the TI Input USB board. This requires a digital or analogaudio source, a 5-V power supply, and the included USB and ribbon cables.
1. Ensure that all external power sources are set to OFF2. Connect an external regulated power supply set to 5 V to the module +5V (J7) and GND (J6), takingcare to observe marked polarity.
1. Ensure that the shunts are fully installed on jumpers J1 and J2. This jumper setting sets the operatingmode of the PCM1606 to I
2
S.2. Install the shunts across J3,J4, or J5, to set the I
2
C address of the TPA5051. J3,J4, and J5correspond to ADD0, ADD1, and ADD2, respectively. Installing the shunt across a given jumper pulls
6TPA5051EVM SLOU184 – July 2006Submit Documentation Feedback

www.ti.com
2
6
34
1
7
Operation
that pin high. The default is 000. Installing a shunt across J3 sets the address to 001.3. Connect the 34-pin ribbon cable between header J800 on the TI Input USB board and header H1 onthe TPA5051EVM.
4. Connect the 16-pin ribbon cable between header J850 on the TI Input USB board and header H3 onthe TPA5051EVM.
5. Connect the USB cable from the USB jack on the PC to the J350 USB Interface on the TI Input USBboard.
6. For additional delay, another TPA5051EVM can be added in series using the 16-pin and 34-pin ribboncables.
7. Install shunts across J6 and J7. For stand alone evaluation, the shunts may be removed allowing forseparate LRCLK and BCLK signals for DATA1 and DATA2.
Note: No pullup resistors are installed on the TPA5051EVM. Doing so interferes with theinitialization of the TI Input USB board in certain circumstances. However, the pads for thepullup resistors, including SDA and SCL ( R13 and R14, respectively), are available on theEVM for populating if the EVM is to be used in a stand-alone fashion
Figure 5. Top Layer of the TPA5051EVM
SLOU184 – July 2006 TPA5051EVM 7Submit Documentation Feedback

www.ti.com
3.4 Operation
Operation
Figure 6. Bottom Layer of the TPA5051EVM
1. Turn on the power supply for the TPA5051EVM.2. Start the TPA505x software.3. Depress the reset button on the TI Input USB board.4. To play to music through digital audio input 1 (DATA1), insert a signal source into the TI Input USBboard. If it is an analog source, insert it into the jack labeled CH1+2.5. To play to music through digital audio input 2 (DATA2), insert a signal source into the TI Input USBboard. If it is an analog source, insert it into the jack labeled CH3+4.6. If the source is digital, insert it into either the RCA jack or the optical jack, and ensure that the switchbetween them is selected properly.7. Play the music or other source.8. Use the GUI to mute the left or right channels, and to delay them.Note: The TI Input USB board is designed to output I
2
S only.9. Use scope probes to view both delayed and nondelayed signals via the DAC. TP1 and TP2 (left andright, respectively) are the delayed signals from DATA_OUT1 of the TPA5051. TP3 and TP4 (left andright, respectively) are the original signals input to DATA1. TP5 and TP6 are the delayed signals fromDATA_OUT2 of the TPA5051. The EVM is not configured to allow the PCM1606 to display the originalsignals input to DATA2.10. External amplifiers can be connected to the output of the PCM1606; however, the supplied AGND testpoint should be used as the ground reference for external amplifiers. Consult the PCM1606 data sheetfor more information regarding this topic.
Note: TP7 and TP8 (SDA and SCL, respectively), are placed for convenient viewing of the I
2
Csignals only. If it is necessary or desired to manually control the TPA5051 withindependent software, the 34 pin connector of the TI Input USB Board must first beremoved.
TPA5051EVM 8 SLOU184 – July 2006Submit Documentation Feedback

www.ti.com
4 Reference
4.1 TPA5051EVM PCB Layers
Reference
Figure 7. TPA5051EVM Top Layer
Figure 8. TPA5051EVM Second Layer
SLOU184 – July 2006 TPA5051EVM 9Submit Documentation Feedback

www.ti.com
Reference
Figure 9. TPA5051EVM Third Layer
Figure 10. TPA5051EVM Bottom Layer
TPA5051EVM 10 SLOU184 – July 2006Submit Documentation Feedback

www.ti.com
4.2 TPA5051EVM Bill of Materials
Reference
Table 1. Bill of Materials
Part No. QTY Value Description Distributor No.
(1)
Manufacturer
Part No.
R1, R2, R3, 5 100k 100K, 1/10W, 0603, 5% P100KGCT-ND PanasonicR4, R5 ERJ-3GEYJ104VR6, R7, R8, 6 10k 10k, 1/10W, 0603, 5% P10KGCT-ND PanasonicR9, R20, ERJ-3GEYJ103VR21
R10, R11, DNP 2k 2k, 1/10W, 0603, 5% P2.0KGTR-ND PanasonicR12, R13, ERJ-3GEYJ202VR14
R15, R17, 4 39 39- Ω, 1/10W, 0603, 1% 311-39.0HRCT-ND YageoR18, R19 RC0603FR-0739RLR16 1 0 ΩJumper 0- Ω, 1/4W, 1206, 5% P0.0ETR-ND Panasonic
ERJ-8GEY0R00VC1, C2, C3, 8 0.1 µF 0.1 µF, X7R, ±10%, 10V, Ceramic, 0603 399-1095-1-ND KemetC4, C6, C7, C0603C104K8RACTUC8, C20C5, C9, 6 560pF 560pF, NPO, ±5%, 50V, Ceramic, 0603 PCC2148CT-ND PanasonicC10, C11, ECJ-1VC1H561JC12, C13C14, C15 2 1 µF 1 µF, X5R, ±10%, 10V, Ceramic, 0603 399-3118-1-ND Kemet
C0603C105K8PACTUC16 1 1 µF 1 µF, X5R, ±10%, 16V, Ceramic, 0805 478-1411-2-ND AVX
0805YD105KAT2AC17, C18, 3 10 µF 10 µF, Tantalum, ±20%,16V, Size A 399-3105-1-ND KemetC19 T494A106M016ASL1 1 600- ΩFerrite 600- ΩFerrite Bead, 0805, 500mA, 200 m Ω445-1554-2-ND TDKBead DCR MMZ2012R601AL2 1 0- ΩJumper 0- ΩJumper, 1/8W, 0805, Ceramic P0.0ACT-ND Panasonic
ERJ-6GEY0R00VH1, H2 2 34 Pin 34 Pins, 2 Rows, 2,54mm Pitch Vertical MolexHeader Male, Center Slot Polarized 87834-3411
OR AMP 104338-7H3, H4 2 16 Pin 16 Pins, 2 Rows, 2,54mm Pitch, Vertical MolexHeader Male, Center Slot Polarized 87834-1611TP1, TP2, DNP Test PointsTP3, TP4,TP5, TP6TP7, TP8 2 Loop Test Test Points Farnell InOneConnectors 8731128
OR Vero 20-2137J1, J2, J3, 7 Jumper, Position, 2mm Header 2163S-36-ND NorcompJ4, J5, J6, 2163-36-01-P2J7
J1, J2, J3, 7 Shunts 2mm Shunts SPE1302-ND Delphi 2JM-GJ4, J5, J6,J7
J8, J9 2 Banana Jack with Knurled Thumbnut J587 Johnson 111-2223-001U1 1 TPA5051 Audio Delay, 16 Pin QFN, RSA Designation Texas InstrumentsU2 1 PCM1606 DAC, 20 Pin, SSOP Texas InstrumentsU3 1 TPS73233 LDO, 5 pin, SOT-23, DBV designation Texas InstrumentsOR
TPS73633U4 1 SN74ABT827 10-bit buffer, 24 pin, PW package Texas Instruments
(1)
Distributor is Digikey, unless otherwise specified.
SLOU184 – July 2006 TPA5051EVM 11Submit Documentation Feedback

www.ti.com
5 TPA5051EVM Schematic Diagram
TPA5051EVM Schematic Diagram
Table 1. Bill of Materials (continued)
Part No. QTY Value Description Distributor No.
(1)
Manufacturer
Part No.
U5 1 EXB- 8 Resistor array, 39- Ω, 5%, 1/16W Y1390TR-ND Panasonic2HV390JV EXB-2HV390JV
The TPA5051EVM schematic diagram is appended to this page.
12 TPA5051EVM SLOU184 – July 2006Submit Documentation Feedback

Tpa5051evm6noB.sch-1 - Thu Jun 01 19:05:22 2006

EVALUATION BOARD/KIT IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATIONPURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling theproduct(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided arenot intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations,including product safety and environmental measures typically found in end products that incorporate such semiconductorcomponents or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regardingelectromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet thetechnical requirements of these directives or other related directives.Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BYSELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDINGANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from allclaims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility totake any and all appropriate precautions with regard to electrostatic discharge.EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHERFOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement ofpatents or services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling theproduct. This notice contains important safety information about temperatures and voltages. For additional information on TI’senvironmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh .No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, orcombination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATIONPURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, andcan radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of thisequipment in other environments may cause interference with radio communications, in which case the user at his own expensewill be required to take whatever measures may be required to correct this interference.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the voltage supply range of 4.5 V to 5.5 V.Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there arequestions concerning the input range, please contact a TI field representative prior to connecting the input power.Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to theEVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the loadspecification, please contact a TI field representative.During normal operation, some circuit components may have case temperatures greater than 85 °C. The EVM is designed tooperate properly with certain components above 85 °C as long as the input and output ranges are maintained. These componentsinclude but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types ofdevices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes nearthese devices during operation, please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2006, Texas Instruments Incorporated

IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’sstandard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support thiswarranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarilyperformed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers shouldprovide adequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, maskwork right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or servicesare used. Information published by TI regarding third-party products or services does not constitute a license from TI to use suchproducts or services or a warranty or endorsement thereof. Use of such information may require a license from a third party underthe patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is anunfair and deceptive business practice. TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or servicevoids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive businesspractice. TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product wouldreasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreementspecifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramificationsof their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-relatedrequirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding anyapplications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and itsrepresentatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade issolely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements inconnection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI productsare designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use anynon-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Amplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandInterface interface.ti.com Digital Control www.ti.com/digitalcontrolLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyLow Power www.ti.com/lpw Video & Imaging www.ti.com/videoWireless
Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2007, Texas Instruments Incorporated