Texas Instruments UCD3138CC64EVM-030 User manual

Using the UCD3138CC64EVM-030
User's Guide
Literature Number: SLUU886A
February 2012–Revised July 2013

User's Guide
SLUU886A–February 2012–Revised July 2013
Control Card for Digitally Controlled Isolated Power
Converters
1 Introduction
The UCD3138CC64EVM-030 evaluation module helps evaluate the UCD3138 device made by Texas
Instruments and aids in the design of digitally controlled isolated power converters. The EVM can be used
either as a stand-alone control card to study the UCD3138 controller device, or as a DPWM controller
board working with a power-stage board to implement a fully regulated power converter. To help the
targeted off-line isolated power applications, this EVM has been designed to work seamlessly with the
UCD3138PFCEVM-026, UCD3138PSFBEVM-027, and UCD3138LLCEVM-028 power-converter EVMs
offered by TI.
Alternately the EVM can also be loaded with custom user-developed firmware. In order to communicate
with the UCD3138 digital controller in this EVM, a separate USB Interface Adapter EVM from TI known as
the USB-TO-GPIO Adapter is required. The USB-TO-GPIO adapter is NOT supplied with
UCD3138CC64EVM-030 evaluation module and must be purchased separately. TI also offers a Graphical
User Interface (GUI) in order to program the UCD3138 controller and configure parameters when used
with the power-converter EVMs mentioned above.
2 Description
The UCD3138CC64EVM-030 is an EVM board, functioning as a control card for UCD3138RGC digital
power-supply applications. This EVM is used to control a power-converter topology such as PFC pre-
regulator, LLC Resonant Half-Bridge DC converter, and Phase-Shifted Full-Bridge DC converter by
downloading the associated firmware and interfacing with an appropriate power stage board. After the
UCD3138 is programmed appropriately, the EVM works seamlessly with the following EVM boards from
Texas Instruments. Please visit www.ti.com to check EVM status and availability.
• UCD3138PFCEVM-026, a digital controlled PFC pre-regulator evaluation board, Texas Instruments
Literature Number, SLUU885
• UCD3138PSFBEVM-027, a digital controlled phase-shift full-bridge DC-to-DC converter evaluation
board
• UCD3138LLCEVM-028, a digital controlled LLC resonant half-bridge DC-to-DC converter evaluation
board, Texas Instruments Literature Number, SLUU979
2.1 Typical Applications
• Isolated Power Supply Applications (such as single-phase, two-phase interleaved or bridgeless PFC,
LLC resonant half-bridge DC-to-DC power converter, phase-shifted full-bridge DC-to-DC power
converter, and hard switching full-bridge DC-to-DC power converter)
• Server Power Supplies and Telecom Rectifiers
• Isolated DC-to-DC Telecom Modules
All trademarks are the property of their respective owners.
2Control Card for Digitally Controlled Isolated Power Converters SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

www.ti.com Specifications
2.2 Features
• 40-Pin Digital Signal Connector to Connect Digital Signals to Power Converters
• 40-Pin Analog Signal Connector to Connect Analog Signals to Power Converters
• JTAG Connector
• LED Indicator
• PMBus Connector to PC Computer Connection Through USB-to-GPIO Adapter
• Rich Test Points to Facilitate the Device Evaluation, System Design, and Circuit and Firmware
Debugging
• 12-V Input Capable With Onboard Regulator 3.3 V
3 Specifications
Table 1. UCD3138CC64EVM-030 Specifications
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS
Connector J1
PMBus connector Port of connection to USB-to-GPIO, pin definition refer Standard
to TI standard USB-to-GPIO document SLLU093
Connector J2
3.3-V connection to PMBus Port to use on board 3.3 VD to bias PMBus(1) 3.25 3.30 3.35 VDC
Connector J3
Analog signal connection Pin definition in compliance with UCD3138 40-pin
Connector J4
Digital signal connection Pin definition in compliance with UCD3138 40-pin
Pin 39 External voltage source input 11.5 12.0 12.5 VDC
Connector J5
JTAG Standard JTAG communication connection Standard
Connector J6
3.3-V on board to external use Port to use 3.3 V on board to bias external circuit 3.27 3.30 3.32 VDC
Operation Environment
Operating temperature range Natural Convection 25 °C
MECHANICAL CHARACTERSTICS
Width 1.8
Dimensions Length 3.4 inches
Component height 0.5
(1) Apply jumper to provide a 3.3-V bias to board from USB-to-GPIO adapter.
3
SLUU886A–February 2012–Revised July 2013 Control Card for Digitally Controlled Isolated Power Converters
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

RESET
Parts not used
1
1 1 1 1
1
1
1
11
1
1
1 1 1
1
1
1
1
1
1
1
1 1 1
1
R14
1.5K
TP2
TP3
TP1
TP6
TP22
TP11
TP23
TP8 TP9
TP10
TP4
TP7
TP16
TP12 TP13
TP14 TP15 TP17 TP18
TP19 TP20
TP21 TP24
TP25
TP26 TP27
TP28
TP29
TP32
TP33
TP34
TP35 TP36
TP30
TP31
1
2
3
4
5
6
7
8
9
10
J1
J2
S1
D1
BAT54A
D2
BAT54A
C31
1000pF
C30
1000pF
C28
1000pF
C29
1000pF
C26
1000pF
C27
1000pF
C24
1000pF
C25
1000pF
C22
1000pF
C23
1000pF
C20
1000pF
C21
1000pF
C18
1000pF
C19
1000pF
C14
1000pF
C7
100pF
C8
1000pF
C17
33pF
C15
33pF
C16
33pF
C9 33pF
C10 33pF
C2
0.1uF
C3
0.1uF
C4
0.1uF
C5
0.1uF
C6
1uF
C11
0.1uF
C12
2.2uF
C1
1uF
C13
0.1uF
R13
1.5K
R12
1.65K
R9 100
R8 100
R7 100
R5 100
R6
0
R3
R1 R2 R4
R11 16K
R10
10K
R15
100K
R16 100
R17 100
R18 100 R20 100
R19 100
R25 100
R23 100
R26 100
R24 2K
R21 2K
R22 2K
R27 2K
R28 2K
R29 2K
NS1
1AGND
2AD13
3AD12
4AD10
5AD07 6AD06
7AD04
8AD03
9
V33DIO
10 DGND
11
RESET
12
ADC_EXT
13
SCI_RX0
14
SCI_TX0
15 PMBUS_CLK
16 PMBUS_DATA
17
DPWM0A
18
DPWM0B
19
DPWM1A
20
DPWM1B
21
DPWM2A
22
DPWM2B
23
DPWM3A
24
DPWM3B
25 DGND
26
SYNC
27 PMBUS_ALERT
28 PMBUS_CTRL
29
SCI_TX1
30
SCI_RX1
31 PWM0
32
PWM1
33 DGND
34
INT_EXT
35
FAULT0
36
FAULT1
37
TCK
38
TDO
39
TDI
40
TMS
41
TCAP
42
FAULT2
43
FAULT3
44 DGND
45
V33DIO
46
BP18
47
V33D
48 AGND
49 AGND
50 EAP0
51 EAN0
52 EAP1
53 EAN1
54
EAP2
55
EAN2
56 AGND
57
V33A
58 AD00
59 AD01
60 AD02
61 AD05
62 AD08
63 AD09
64 AD11
65 PWPD
U1
UCD3138RGC
TP5
R39 10
AD-00
SCI-RX1
SCI-TX1 SCI-TX0
SCI-RX0
EXT-TRIG
DPWM-2B
DPWM-2A
DPWM-1B
DPWM-1A
DPWM-0B
DPWM-0A
/RESET
TMS
TDI
TDO
TCK
PWM-1
PWM-0
AD-06
AD-05
AD-04
AD-03
AD-00
EADC-N1
EADC-P1
EADC-N0
DGND
AD-02
AD-07
DPWM-3A
DPWM-3B
EADC-P2
EADC-N2
SYNC
FAULT-0
TCAP
AD-09
AD-10
AD-12
AD-13
EADC-P0
AD-08
AD-01
AD-11 FAULT-3
FAULT-2
FAULT-1
DGND
/RESET
DGND
INT-EXT
DGND
DGND
PMBUS-CTRL
PMBUS-CLK
PMBUS-ALERT
PMBUS-DATA
3.3VD
3.3VD
3.3VD
3.3VD
DGND
DGND
DGND
3.3VA
AGND
AGND
AGND DGND
Schematics and Test Points www.ti.com
4 Schematics and Test Points
Figure 1. UCD3138CC64EVM-030 Schematic
4Control Card for Digitally Controlled Isolated Power Converters SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

If needed, use this jumper
to provide 3.3VD to application board
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
J3
PPPN202FJFN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
J4
PPPN202FJFN
1
IN
2
NC
3
NC
4
GND
5FB/NC
6NC
7NC
8OUT
9PWPD
U2
TPS715A33DRBR
TP37
C33
10uF
C32
1uF
R31
301
R30
0.5
R35
10K
R32
10K
R33
10K
R37 10K R38 10K
R34
0
R36
0
D3
J6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
J5
C34
0.1uF
EADC-N2
EADC-N1
EADC-N0
EADC-P0
EADC-P1
EADC-P2
AD-00
AD-01
AD-02
AD-03
AD-04
AD-05 AD-06
AD-07
AD-08
AD-09
AD-10
AD-11
AD-12
AD-13
DPWM-0A
DPWM-1A
DPWM-2A
DPWM-3A
FAULT-0
SYNC
FAULT-2
SCI-TX1 PWM-0
TCAP
SCI-TX0
INT-EXT
+12V_EXT
DPWM-0B
DPWM-1B
DPWM-2B
DPWM-3B
FAULT-3
SCI-RX1
PWM-1
SCI-RX0
EXT-TRIG
/RESET
3.3VD
TMS
TDI
TDO
TCK
DGND
+12V_EXT
FAULT-1
3.3VD
3.3VD
3.3VD
DGND
DGND
AGND
www.ti.com Schematics and Test Points
Figure 2. UCD3138CC64EVM-030 Schematic
5
SLUU886A–February 2012–Revised July 2013 Control Card for Digitally Controlled Isolated Power Converters
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

Schematics and Test Points www.ti.com
4.1 List of Test Points
The functions of each test point for the UCD3138CC64EVM-030.
Table 2. Test Point Functions
TEST POINTS NAME DESCRIPTION
TP1 3.3VA 3.3-V analog on board
TP2 RC filter 2B DPWM2B RC filter
TP3 RC filter 3A DPWM3A RC filter
TP4 PWM-0 PWM0
TP5 AGND Analog GND
TP6 DGND Digital GND
TP7 PWM-1 PWM1
TP8 EADC-N0 EAN0
TP9 EADC-P1 EAP1
TP10 EADC-P0 EAP0
TP11 EADC-N1 EAN1
TP12 DPWM-0A DPWM0A
TP13 DPWM-0B DPWM0B
TP14 DPWM-1A DPWM1A
TP15 DPWM-1B DPWM1B
TP16 TCAP TCAP
TP17 DPWM-2A DPWM2A
TP18 DPWM-2B DPWM2B
TP19 DPWM-3A DPWM3A
TP20 DPWM-3B DPWM3B
TP21 AD-00 A to D converter channel AD01
TP22 EADC-N2 EAN2
TP23 EADC-P2 EAP2
TP24 AD-01 A to D converter channel AD00
TP25 to 36 AD-02 to -13 A to D converter channels AD02 to AD13
TP37 +12V_EXT External 12 V
J1 PMBus Connection PMBus connector, 10 pins
J2 +3.3VD Jumper header, if jump across, 3.3 V supplied from USB connection
J3 Analog Connection 40-pin header, analog signals
J4 Digital Connection 40-pin header, digital signals
J5 JTAG Connection 14-pin header, JTAG connector
J6 +3.3VD Jumper header, if jump across, 3.3 V supplied to outside need
S1 Reset UCD3138 reset, press to reset.
6Control Card for Digitally Controlled Isolated Power Converters SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

USB - Mini B LED Indicator
Ribbon Cable
I/O Port
www.ti.com Test Equipment
5 Test Equipment
5.1 PC Computer
5.1.1 Operating System
Microsoft Windows XP (32 bit), or Vista (32 bit), or Windows 7 (32 bit).
5.2 USB-to-GPIO Interface Adapter
This adapter (not included in this EVM, order separately) establishes the communication between the
control card UCD3138CC64EVM-030 and the PC computer through the PMBus and the GUI, Texas
Instruments Fusion Digital Power Designer.
5.2.1 USB-to-GPIO Interface Adapter (HPA172)
Accessories included:
• USB Interface Adapter
• USB Cable, 5-pin B Mini Male to Type A Male
• Ribbon Cable, Socket-to-Socket, 10 Pin, 2 Headers, Polarized
Figure 3. USB-to-GPIO Interface Adapter Outlook
5.3 Oscilloscope
An oscilloscope of analog or digital type is capable of 200-MHz bandwidth with Tektronix P6138 or
equivalent oscilloscope probe.
7
SLUU886A–February 2012–Revised July 2013 Control Card for Digitally Controlled Isolated Power Converters
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

Equipment Setup www.ti.com
6 Equipment Setup
6.1 GUI Setup
6.1.1 File for Installation
The GUI installation file is TI-Fusion-Digital-Power-Designer-Version-1.8.92.exe or newer version. To get
the latest version of GUI, go to the Fusion Digital Power Designer tool folder (Texas Instruments Fusion
Digital Power Designer) on the TI Web site, download, and install on computer.
6.1.2 Installation
Double click and launch the .exe file to start the installation. Click Next all the way through. When
prompted, read through the agreement and click I accept the agreement when finished. Then click install.
After the installation, click Finish to exit setup. Then click Exit Program.
6.1.3 Launch UCD3138 Device GUI
The GUI for UCD3138CC64EVM-030 board can be launched through the following steps:
1. Click the window Start
2. Click All Programs
3. Click Texas Instruments Fusion Digital Power Designer
4. Click Device GUIs
5. Click UCD3xxx Device GUI
Figure 4. Device GUI Launch Path
8Control Card for Digitally Controlled Isolated Power Converters SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

USB-to-GPIO
PC Computer
USB Adapter LED
UCD3138CC64EVM-030
EVM LED
J6
J2
Reset Button
www.ti.com Equipment Setup
6.2 Hardware Setup
6.2.1 Setup Overview
The connection between UCD3138CC64EVM-030 and the PC computer through USB-to-GPIO Interface
Adapter is shown in Figure 5.
For USB adapter connection, complete the following:
• Connect one end of the ribbon cable to the EVM, and connect the other end to the USB interface
adapter.
• Connect the mini connector of the USB cable to the USB interface adapter, and connect the other end
to the USB port of the PC computer.
Figure 5. UCD3138CC64EVM-030 Test Connections
9
SLUU886A–February 2012–Revised July 2013 Control Card for Digitally Controlled Isolated Power Converters
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

Test Procedure www.ti.com
7 Test Procedure
7.1 Download Firmware Codes to UCD3138CC64EVM-030
See Figure 5 to set up the EVM connection.
1. Set up the EVM connection based on Figure 5. The LED of USB adapter lights up.
2. Use the provided jumper jump across J2. The LED of the EVM lights up.
3. Launch the UCD31xx device GUI following the steps described in Section 6.1.3. The window shown in
Figure 6 appears.
4. Click Firmware Download and a new window appears as shown in Figure 7. Click Select File and
browse an intended firmware code file with file extension .x0, for example, cyclone.x0. Then click
Download. TI recommends not writing the program checksum (stay in ROM) during firmware
development or debug state. The firmware of cyclone.x0 downloads to the device UCD3138 on the
board of UCD3138CC64EVM-030. When asked, click yes to complete the download. Click Close to
exit the download window.
5. After the firmware codes download to the UCD3138 device, the intended test can be performed. For
example, with the provided firmware cyclone.x0, one can observe voltage toggled between 0 V and 3.3
V on test point TP7.
7.2 Erase Firmware Codes from UCD3138CC64EVM-030
Erasing the downloaded firmware codes from UCD3138 flash memory can be made with the steps below
based on Figure 6.
1. Click Device ID
2. Click Command Program to jump to ROM (SendByte.0xD9)
3. Click Erase/Set PFlash: 0xFF
7.3 Equipment Shutdown
1. Exit the GUI
2. Disconnect the USB cable and the ribbon cable
Figure 6. UCD31xx Device GUI
10 Control Card for Digitally Controlled Isolated Power Converters SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

www.ti.com Test Procedure
Figure 7. Firmware Code Downloading
11
SLUU886A–February 2012–Revised July 2013 Control Card for Digitally Controlled Isolated Power Converters
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

EVM Assembly Drawing and PCB layout www.ti.com
8 EVM Assembly Drawing and PCB layout
The following figures (Figure 8 through Figure 13) show the design of the UCD3138CC64EVM-030 printed
circuit board. PCB dimensions: L × W = 3.4 in × 1.8 in, PCB material: FR4 or compatible, four layers and
1-oz copper on each layer.
Figure 8. UCD3138CC64EVM-030 Top Layer Assembly Drawing (top view)
Figure 9. UCD3138CC64EVM-030 Bottom Assembly Drawing (no components on this side)
12 Control Card for Digitally Controlled Isolated Power Converters SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

www.ti.com EVM Assembly Drawing and PCB layout
Figure 10. UCD3138CC64EVM-030 Top Copper (top view)
Figure 11. UCD3138CC64EVM-030 Internal Layer 1 (top view)
13
SLUU886A–February 2012–Revised July 2013 Control Card for Digitally Controlled Isolated Power Converters
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

EVM Assembly Drawing and PCB layout www.ti.com
Figure 12. UCD3138CC64EVM-030 Internal Layer 2 (top view)
Figure 13. UCD3138CC64EVM-030 Bottom Copper (top view)
14 Control Card for Digitally Controlled Isolated Power Converters SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

www.ti.com List of Materials
9 List of Materials
Table 3 lists the EVM components according to the schematic shown in Figure 1 and Figure 2.
Table 3. UCD3138CC64EVM-030 List of Materials
QTY RefDes Description Part Number MFR
3 C1, C6, C32 Capacitor, ceramic, 16 V, X7R, ±10%, 1 µF, 0603 STD STD
1 C12 Capacitor, ceramic, 16 V, X5R, ±10%, 2.2 µF, 0603 STD STD
7 C2, C3, C4, C5, Capacitor, ceramic, 16 V, X7R, ±10%, 0.1 µF, 0603 STD STD
C11, C13, C34
1 C33 Capacitor, ceramic, 10 V, X5R, ±10%, 10 µF, 0805 STD STD
1 C7 Capacitor, ceramic, 50 V, X7R, ±10%, 100 pF, 0603 STD STD
16 C8, C14, C18, Capacitor, ceramic, 50 V, X7R, ±10%, 1000 pF, 0603 STD STD
C19, C20, C21,
C22, C23, C24,
C25, C26, C27,
C28, C29, C30,
C31
5 C9, C10, C15, Capacitor, ceramic, 50 V, NP0, ±10%, 33 pF, 0603 STD STD
C16, C17
2 D1, D2 Diode, dual Schottky, common anode, 300 mA, 30 V, SOT23 BAT54AFILM ST
1 D3 Diode, LED, green, 2.1 V, 20 mA, 6 mcd, 0603 LTST-C190GKT Lite On
1 J1 Header, 2 × 5 pin, 100-mil spacing 5103308-1 Tyco
2 J2, J6 Header, male 2 pin, 100-mil spacing PEC02SAAN Sullins
2 J3, J4 Conn header 2-mm dual R/A 40POS PPPN202FJFN-RC Sullins
1 J5 Header, male 2 × 7 pin, 100-mil spacing PEC07DAAN Sullins
0 R1, R2, R3, R4 Resistor, chip, 1/16 W, 1%, open, 0603 STD STD
6 R10, R32, R33, Resistor, chip, 1/16 W, 1%, 10 kΩ, 0603 STD STD
R35, R37, R38
1 R11 Resistor, chip, 1/16 W, 1%, 16 kΩ, 0603 STD STD
1 R12 Resistor, chip, 1/16 W, 1%, 1.65 kΩ, 0603 STD STD
2 R13, R14 Resistor, chip, 1/16 W, 1%, 1.5 kΩ, 0603 STD STD
1 R15 Resistor, chip, 1/16 W, 1%, 100 kΩ, 0603 STD STD
R21, R22, R24,
6 Resistor, chip, 1/16 W, 1%, 2 kΩ, 0603 STD STD
R27, R28, R29
1 R30 Resistor, chip, 1/16 W, 1%, 0.5 Ω, 0603 STD STD
1 R31 Resistor, chip, 1/16 W, 1%, 301 Ω, 0603 STD STD
1 R39 Resistor, chip, 1/10 W, 1%, 10 Ω, 0805 Std Std
12 R5, R7, R8, R9, Resistor, chip, 1/16 W, 1%, 100 Ω, 0603 STD STD
R16, R17, R18,
R19, R20, R23,
R25, R26
3 R6, R34, R36 Resistor, chip, 1/16 W, 1%, 0 Ω, 0603 STD STD
1 S1 Switch, SPST, PB momentary, sealed washable, 0.245 x KT11P2JM-34LFS C & K
0.251
1 U1 Digital Power Controller, PFC-64 UCD3138RGC TI
1 U2 High Input Voltage, Micro power, 3.2 µA at 80 mA LDO, 3.3 TPS715A33DRBR TI
V, QFN-8
15
SLUU886A–February 2012–Revised July 2013 Control Card for Digitally Controlled Isolated Power Converters
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

www.ti.com
Appendix A Summary of Using Code Composer Studio v3.3
This appendix describes the basic steps on how to use Code Composer Studio v3.3, or CCS, to compile
firmware for UCD3138. The design flow describes detailed steps for firmware code creation and firmware
debugging.
A.1 Set Up Code Composer Studio v3.3 for UCD3138
The recommended version of Code Composer Studio is version 3.3 (v3.3). After completing the CCS v3.3
installation, and when CCS is opened for the first time, the window shown in Figure 14 prompts users to
select the required configuration. For UCD3138 device, please select ARM7 SIMULATOR BIG ENDIAN.
Click ADD and then Save & Quit.
If CCS has existing configurations in My System, click Launch Setup under File pull-down menu. Select
Remove All to remove the existing configurations; then select ARM7 SIMULATOR BIG ENDIAN as shown
in Figure 14, Click ADD and then Save & Quit for UCD3138 device.
Figure 14. Set Up Code Composer Studio v3.3 for UCD3138
16 Summary of Using Code Composer Studio v3.3 SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

www.ti.com Build and Compile a Project Using Code Composer Studio
A.2 Build and Compile a Project Using Code Composer Studio
After a project is created with all source codes developed, one can compile the project using CCS.
A.2.1 Creating a Project
The example below describes the typical compile process for UCD3138 firmware. The project file name is
Cyclone.pjt and it is located in the folder named Training 02. The final result of the compile process is a
file with the file extension of .x0. Because the project name is Cyclone.pjt, the final file name of Cyclone.x0
is naturally chosen. Cyclone.x0 is the final firmware code downloaded to the UCD3138 device memory for
the UCD3138 intended functional operation. The following are the steps for a typical compile process:
1. Copy file folder Training 02 and paste into any desired directory inside the PC.
2. Launch CCS and open the CCS project file Cyclone.pjt from the directory where Training 02 was
saved. The window shown in Figure 15 appears.
• Note, because the project Cyclone.pjt has been created and designed for UCD3138 functions,
CCS can be launched without connecting an emulator.
3. From CCS project window, Right click on Cyclone.pjt (Debug) and then select Build Options. The
window shown in Figure 16 appears when the Linker tab is selected.
•Figure 16 shows the project Build Options have been selected to create the file Cyclone.out from
CCS.
4. Convert the file Cyclone.out to Cyclone.x0.Cyclone.x0 is the final firmware code downloaded to the
UCD3138 device memories. To convert Cyclone.out to Cyclone.x0, first click theGeneral tab under
Build Options for Cyclone.pjt (Debug), as shown in Figure 17. Second, under the Build Command,
confirm that the file to be converted is Cyclone.out. Third, click ok to close Build Options.
Steps 4, 5, and 6 are only necessary once per project. If using a platform with TI developed
firmware, these steps have been set up and there is no need to repeat.
5. Select Project Rebuild All, as shown in Figure 18.Project Rebuild All generates the file Cyclone.x0
based on Cyclone.out, and saves the file of Cyclone.x0 inside the folder where Cyclone.pjt is saved.
Figure 15. Open a Project File with Example of Cyclone.pjt – Initial Open.
17
SLUU886A–February 2012–Revised July 2013 Summary of Using Code Composer Studio v3.3
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

Build and Compile a Project Using Code Composer Studio www.ti.com
Figure 16. Open a Project File with Example of Cyclone.pjt – Build Options and Linker Tab
Figure 17. Open a Project File With Example of Cyclone.pjt - Build Options and General Tab
18 Summary of Using Code Composer Studio v3.3 SLUU886A–February 2012–Revised July 2013
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated

www.ti.com References
Figure 18. Opened Project File With Example of Cyclone.pjt - Rebuild All
A.3 References
1. UCD3138 Datasheet, Highly Integrated Digital Controller for Isolated Power, Texas Instruments
Literature Number, SLUSAP2
2. Code Composer Studio Development Tools v3.3 – Getting Started Guide, Texas Instruments Literature
Number, SPRU509
3. Reference Guide, UCD3138 Digital Power Peripherals Programmer’s Manual, Texas Instruments
Literature Number, SLUU995
4. Reference Guide, UCD3138 Monitoring and Communications Programmer’s Manual, Texas
Instruments Literature Number, SLUU996
5. Reference Guide, UCD3138 ARM and Digital System Programmer’s Manual, Texas Instruments
Literature Number, SLUU994
6. User's Guide, UCD3138 Isolated Power Fusion GUI, (please contact TI).
19
SLUU886A–February 2012–Revised July 2013 Summary of Using Code Composer Studio v3.3
Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.