Texmate CL-B101D40HZ User manual

CL-B101D40HZ Manual (d0098) Page 1
CL-B101D40HZ
Smart 101 segment, 4 digit LED Tricolor or
Mono-color digital line frequency bargraph controller
with four fully programmable set points
in a switchboard style case for
monitoring, measurement, and control applications.
0.56” LEDs
• Frequencyinput.Easilyuserscaled.
• Optional isolated 16 bit analog output. User or factory scalable to 4
to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span
from ± one count to the full scale range of – 1999 to 9999 (12000
counts).
• A Programmable Tricolor (Red-Green-Orange) or mono color (red or
green), 101 segment high brightness bargraph.
• Red 4-digit LED display with a range of 99.99 to 999.9Hz
Optional green digital display.
• FrontpanelLEDannunciatorsprovideindicationofsetpointstatus.
• Two9AmpFormC,andtwo4AmpFormAor4x4AmpFormA
relaysavailable .
•  Auto-sensingAC/DCpowersupply.Forvoltagesbetween
85-265 V AC / 95-300 V DC (PS1)or18-48VAC/10-72VDC
(PS2).
•  Provisiontoconnectanexternalprogramminglockoutswitch.
•  ProvisionforexternalDIMswitchtoreducethebrightest
display setting by 50%.
•  Automaticintelligentaveraging,smoothsnoisysignalswhile
providingafastdisplayresponsetoreallevelchanges.
General Features
Specifications
• Thebargraphcandisplay,full
scale, any desired portion of
the digital reading.
• Setpoint1hasdelay-on-make
anddelay-on-breakplusaspe-
cial “pump on pump off” mode
that creates a Hysteresis Band
between SP1 and SP2.
• Fourprogrammablesetpoints
withadjustableHysteresis.•
Software Features
Bargraph center zero function.
• Relayactivationcanbeselected
tooccurabove(hi)orbelow(Lo)
each setpoint.
• Digitaldisplayblanking.
• Decimalpointsetting.
• Four-levelbrightnesscontrol
BargraphCenterPointDisplayModeSelection ... 6
BargraphColorProgrammingMode ........ 9
CaseDimensions ...................... 13
ComponentLayout..................... 11
ConnectorPinoutsandPinDescriptions..10-11
ControlsandIndicators .................. 2
Decimal Point and Brightness Selection ..... 5
Range Selection Mode................... 7
ProgrammingConventions................ 2
SetpointSetting&RelayConfigurationMode....8-9
SoftwareFeatures ...................... 1
Software Logic Tree ..................... 3
Specifications.......................... 1
TwoPointAnalogRangeSetting&Calibration .... 7
Digital Rescaling Procedures .............. 4
Digital Span Selection for Display .......... 5
Digital Span Selection for Analog Range Output... 6
FunctionalDiagram .................... 10
GeneralFeatures ....................... 1
I-SeriesInputSignalConditioningModules ..... 12
Installationguidelines ................... 13
OrderingInformation ................... 14
LEOPARD
FAMILY
Input Specs:������������������ Depends on Input signal conditioner
A/D Converter:�������������� 14 bit single slope
Accuracy:���������������������� ±(0�05% of reading + 2 counts)
Temp. Coeff�:����������������� 100 ppm/°C (Typical)
Warm up time:��������������� 2 minutes
Conversion Rate:���������� 10 conversions per second (Typical)
Digital Display:�������������� 4 digit 0.56" LED red (std), green (optn)
Range –1999 to 9999 counts�
Bargraph Display:��������� 101 segment 235º circular red (standard),
Green (optional) or tricolor (optional) LED�
Polarity:������������������������� Assumed positive� Displays – negative
Decimal Selection:�������� Front panel button selectable, X•X•X•X•
Positive Overrange:������ Bargraph and top segments of digital display
flash�
Negative Overrange:���� First segment of bargraph and bottom seg-
ments of digital display flash�
Relay Output:���������������� Two 9 Amp Form C relays, two 4 Amp Form
A relays or 4x4AmpFormArelays
Analog Output:������������� Isolated 16 bit user scalable mA or V
OIC (mA out) �������������� 4-20 mA @ 0 to 500٠max loop resistance
OIV (volts out) �������������� 0-10 V DC @ 500 ٠or higher resistance
Power Supply:��������������� AC/DC Auto sensing wide range supply
PS1 (std)�������������������� 85-265 VAC / 95-300 VDC, 50-400Hz 4.2W
PS2����������������������������� 18-48 VAC / 10-72 VDC, 50-400Hz 4�2W
Operating Temp�: ���������� 0 to 50°C
Storage Temp:��������������� –20°C to 70°C
Relative Humidity:�������� 95% (non condensing)
Case Dimensions:�������� Bezel (4.48"x4.48") 113.8x113.8mm
Depth behind bezel (4.23") 107.46 mm
Plus (0�48”) 12�24 mm for connectors
Weight:��������������������������� 16 oz�, 1lb 4 oz when packed
Table of Contents

Page 2 CL-B101D40HZManual(d0098)
Front Panel Buttons
Program Button
The
P
buttonisusedtomovefromoneprogramsteptothenext.
When pressed at the same time as the button, it initiates the
calibration mode. When pressed at the same time as the but-
ton, it initiates the setpoint setting mode.
101 Segment
Bargraph
Up Button
When in the operational display, pressing the button allows you
toviewthesettingofthesaved Peak and Valley Values.
When setting a displayed parameter during programming, the
buttonisusedtoincreasethevalueofthedisplayedparameter.
Down Button
When in the operational display, pressing the button allows you
to change the Brightness Level aswellastoviewthesettingof
the setpoints SP1, SP2, SP3 & SP4.
When setting a displayed parameter during programming, the
buttonisusedtodecreasethevalueofthedisplayedparameter.
Front Panel LED Display
Annunciator LEDs
The annunciator LEDs indicate the alarm status. They are labeled
from bottom to top: SP1, SP2, SP3, SP4.
Digital LED Displays
The digital LED displays are used to display the meter input
signal readings. They also display the programming settings
during programming.
Setpoint Indication
The position of setpoints on the bargraph display are indicated by
anONorOFFsegmentdependentonthebargraphdisplaybeing
aboveorbelowthesetpoint.
Setpoints
indicated
by an ON
Segment
Setpoints indicated
by an OFF Segment
Controls and Indicators
This symbol represents the
OPERATIONALDISPLAY.
This is the PROGRAM button.
This is the UP button.
This is the DOWN button.
When a button is shown, press and
releaseit togo onto thenext step inthe
direction indicated by the arrow. When
an alternative dotted line is shown, this
indicates that an alternative logic branch
will be followed when a particular option
is present.
When two buttons are shown side by side
and enclosed by a dotted line, they must
be pressed at the same time then released
togoontothenextprogrammingstep.
IfanXappearsthroughadigit,itmeansthat
any number displayed in that digit is not rel-
evanttothefunctionbeingexplained.
P
[Span]
[10000]
P
P
When the and buttons are shown
together,thedisplayvaluecanbeincreased
by pressing and releasing the button
or decreased by pressing and releasing the
button.
When the and buttons are shown
with two displays, either display can be
selected by pressing and releasing the or
buttons.
When two displays are shown together
with bursts, this indicates that the display is
toggling (flashing) between the name of the
functionandthevalue.
Text or numbers shown between square
brackets in a procedure indicate the pro-
gramming code name of the function or the
valuedisplayedonthemeterdisplay.
When there are more than two display selec-
tionstheyareshowninbracketsbelowthe
first display and are also selectable by
pressing and releasing the or buttons.
A dotted line enclosing an entire logic dia-
gram indicates that programming branch
will appear only when a particular option is
present.
Toexplainsoftwareprogrammingprocedures,logicdiagramsare
usedtovisuallyassistinfollowingtheprogrammingsteps.The
following symbols are used throughout the logic diagrams to
represent the buttons and indicators on the meter:
Programming Conventions
[X•XXX]
[XX•XX]
[XXX•X]
[XXXX•]
[XXXX]
Front Panel Controls and Indicators
LED
Annunciators
for Setpoints
1-4
Single or
Tri-color
Bargraaph
Display
UP
Button
DOWN
Button
PROGRAM
Button
7 Segments
Digital
Display

CL-B101D40HZ Manual (d0098) Page 3
Software Logic Tree
The CL-B101D40HZ is an intelligent bargraph meter with a hier-
archical software structure designed for easy programming and
operation, as shown below in the software logic tree.
vWhen power is applied, all segments of the bargraph and
digital display light up for 3 seconds. The version number of
the installed software is then displayed for 2 seconds, after
which, the operational display indicates the input signal.
15 Second Program Timeout
Except for ZERO and SPAN settings in the Two
Point Digital Calibration Mode and the Analog
Output Range Setting and Calibration Mode
(cLo and chi), the meter has a 15 second
program timeout. If no buttons are pressed for
15 seconds in any of the other programming
sequences, the meter will exit the program-
ming mode and return to the operational
display. Any program changes that were made
prior to pressing the
P
button in the preced-
ing step will not be saved.
Peak
Reset
PEAK
Reset
VA LY
Valley
PEAK & VALLEY
VIEW & RESET
Operational Display
MAIN MENU
Bargraph Center Point
Display Selection (cto)
This branch will
only appear if
the analog
output option
is installed
Back to
Operational
Display
Digital Display ON/OFF
Selection (diSP)
Sub-menu MODE
Calibration Mode
Calibration
Input
Calibration
Output
offset
(ZEro)
Scale
Factor
(SPAn)
Calibrate Analog
Output Lo
Calibrate Analog
Output Hi
Select the Digital
Reading at which
the Analog Output
Hi (chi) will occur
Select the Digital
Reading at which
the Analog Output
Lo (cLo) will occur
This branch will only
appear, if the analog
output option
is installed
DIGITAL SPAN SELECTION
FOR ANALOG RANGE OUTPUT
See Page 6
DIGITAL DISPLAY ON/OFF
See Page 6
RANGE SELECTION
See Page 7
BARGRAPH CENTER POINT
DISPLAY MODE SELECTION
See Page 6
TWO POINT ANALOG OUTPUT
RANGE SETTING AND CALIBRATION
See Page 7
Set the Decimal
Point (dp)
Bargraph Display
Scale Lo Range
Setting (bLo)
Bargraph Display
Scale hi Range
Setting (bhi)
Display
Brightness (br)
1 Dimmest
2 Dim
3 Bright
4 Brightest
[X•XXX]
[XX•XX]
[XXX•X]
[XXXX•]
[XXXX]
DECIMAL POINT AND
BRIGHTNESS SELECTION
See Page 5
DIGITAL SPAN SELECTION
FOR BARGRAPH DISPLAY
See Page 5
Goes directly
to Zero setting
if Analog Output
is not installed
+
–
4.00
+
–
20.00
Range
[99•99]
[9999]
[999•9]
Select one of three
Ranges: 99.99Hz,
999.9Hz or 9999Hz
PROGRAMMABLE
OFFSET AND
SCALE FACTOR
See Page 4
[orAn]
[rEd]
NOTE: Will only
appear if a tricolor
display is installed
[orAn]
[rEd]
[orAn]
[rEd]
[orAn]
[rEd]
[orAn]
[rEd]
BARGRAPH COLOR
PROGRAMMING MODE
See Page 10
Tricolor Bargraph
The tri-color bargraph is designed
like a traffic light, to display either
red, orange or green, but only one
color at a time. The color to be
displayed is selected in two ways.
The first step is to select the color
to be displayed when the bar is
“below” whichever set point is set
to the lowest position.
The second step is to select the
color to be displayed when the bar
is above each specific setpoint,
regardless of the order or position
to which the set points are set.
However, if two or more setpoints
with differently specified colors are
positioned at the same set point
value, the color specified for the set
point with the highest identifying
number will be displayed. When
setpoints are set to the same value,
the SP4 color overrides the SP3
color, the SP3 color overrides the
SP2 color, and the SP2 color
overrides the SP1 color.
SETPOINT SETTING AND
RELAY CONFIGURATION MODE
See Page 9
L or h
L or h
L or h
L or h
Relays
Activation [rLYS]
(h) High
the relay
energizes
when the setpoint
is exceeded
(L) Low
the relay
energizes below
the setpoint.
Pump On Pump Off [PUM]
When PUM is selected on,
and SP2 is set at a value
higher than SP1, the SP1
relay will operate in a special
"pump on pump off"
Hysteresis mode. SP2 acts
as the upper limit and SP1
acts as the lower limit of the
Hysteresis Band.
For filling applications, rLYS
should be set to LhLh. SP1 will
then activate for inputs less than
the SP1 setpoint, and remain
ON until the SP2 setpoint is
reached.
For emptying applications,
rLYS should be set to hhhh.
SP1 will then activate for inputs
greater than the SP2 setpoint,
and remain ON until the SP1
setpoint is reached.
Set Setpoint 1
[SP1]
Delay-on-Make
[doM]
Delay-on-Break
[dob]
Setpoint 2
[SP2]
NOTE: [dom] [dob]
Functions are only
available for SP1
0 to 9999
seconds
0 to 9999
seconds
Pump
[PUM]
Hysteresis
[hYSt]
Hysteresis
[hYSt]
Hysteresis
[hYSt]
Hysteresis
[hYSt]
Setpoint 3
[SP3]
Setpoint 4
[SP4]
BRIGHTNESS AND
SETPOINT VIEW MODE
1 Dimmest
2 Dim
3 Bright
4 Brightest

Page 4 CL-B101D40HZManual(d0098)
STEP A Enter the Calibration Mode
1) Press the
P
and buttons at the same time. Display
toggles between [CAL] and [oFF].
2) Press the or button. Display changes from [oFF] to
[on].
3) Press the
P
button. Display toggles between [CAL] and
[out].
Note: If at this point, the display skips directly to STEP C and toggles
between [ScAL] and the previous [ScAL] setting, the software
is detecting that the optional analog output hardware is NOT
installed.
STEP B Select Two Point Digital Calibration of Input Signal
1) Press the or button to select CAL [iP] for input signal
calibration.
2) Press the
P
button. Display toggles between [oFFS] and the
previous offset setting.
STEP C Set the Offset on the Digital Display
1) Using the and buttons, adjust the digital display to
the desired offset. This is the reading that the meter will dis-
play for a zero input
2) Press the
P
button. Display toggles between [ScAL] and
the previous Scale factor.
STEP D Set the Scale factor on the Digital Display
1) Using the and buttons, adjust the meter display to
the desired Scale factor. The default value is 2000, for which a
2V input will read 2000. If the scale factor is changed the
display will change proportionately. Therefore if the Scale
factor is changed to 1000 then for the same 2V input the dis
play would read 1000.
2) Press the
P
button.
The Digital Rescaling is now complete.
If the Digital Rescaling was successfully completed, the
menu branches to the Digital Span Selection for Bargraph
Display (see page 6), and the display flashes [bhi] and the
previous setting.
The CL-B101D40HZManual(d0096) meter may be rescaled without applying an external signal by changing the Offset and Scale
factor.
Offset is the reading that the meter will display for a zero input. The Offset may be set to any value from -1999 to +9999. The
default value of the Offset is 000
Scale factor is the gain of the meter. The displayed reading is directly proportional to the Scale factor. The default value of the
scale factor is 2000, but it may be set to any value between -1999 and +9999.
For an input of 2V a calibrated meter will read 2000 with the default Scale factor of 2000, 3000 with a Scale factor of 3000 and
500 with a Scale factor of 500
If a linear scale is represented by mx + b, then the Scale Factor corresponds to the slope ‘m’ and the Offset corresponds to
the intercept ‘b’
The internal Signal Span is limited to 3 V DC between – 1 V DC to + 2 V DC. Outputs from an Input Signal Conditioning module
that exceed these limits will cause the meter to indicate overrange.
Note: Most input signal conditioners have provisions for analog calibration and scaling. If the meter’s digital Scale Factor is
set to 2000 and Offset set to 0000 then, any pre-calibrated signal condi-
tioner with an output that does not exceed – 1 V to + 2 V, will read correct-
ly in the meter without any further calibration.
Digital Rescaling
Digital Rescaling Procedure
MAIN MENU
Operational Display
Sub-menu
MODE
STEP A Calibration
Mode
STEP B Calibration
Mode
STEP C Offset
STEP D Scale
Factor
To Digital Span Selection for
Bargraph Display Page 6
cAL out/iP branch will only
appear if the analog output
option is installed, otherwise
cAL on goes directly to ZEro
setting
DIGITAL
RESCALING MODE
To Digital Span Selection
for Bargraph Display
See Page 7
To Two Point Analog
Output Range Setting
and Calibration
See Page 8

CL-B101D40HZ Manual (d0098) Page 5
Example
Example
From Two Point
Digital Calibration
Mode See Page 4
STEP A
STEP B
STEP C
STEP D
See Example Above
of Bargraph Display
Scale Range
To Digital Span Selection
for Analog Range Output or
Bargraph Center Point
Display Mode Selection
on Page 6 or 7
DIGITAL SPAN SELECTION
FOR BARGRAPH DISPLAY
[X•XXX]
[XX•XX]
[XXX•X]
[XXXX•]
[XXXX]
DECIMAL POINT AND
BRIGHTNESS SELECTION
STEP A Enter the Calibration Sub Menu Mode
1) Press the
P
and buttons at the same time. Display toggles
between[CAL]and[oFF].
2) Press the
P
 button. Display toggles between [bhi] and the
previous setting.
STEP B Set the Digital Span of the Bargraph Display (See example
above)
1) Using the and buttons, adjust the display to the
desired high parameter reading, e.g. 6000 counts.
2) Press the
P
 button. Display toggles between [bLo] and the
previoussetting.
3) Using the and buttons, adjust the display to the
desired low parameter reading, e.g. 4000 counts.
4) Press the
P
button.Displaychangesfrom[4000]to[dP].
STEP C Set the Decimal Point
1) Using the and buttons, adjust the display to the
desired decimal point setting.
2) Press the
P
button.Displaytogglesbetween[br]andthe
 previousbrightnesssetting.
STEP D Set the Bargraph and Digital Display Brightness
1) Using the and buttons, adjust the display to the
desired brightness setting (4 is the brightest setting).
2) Press the
P
button.Displaytogglesbetween[Anhi]and
 theprevious[Anhi]setting.
Note: If at this point, the display skips directly to STEP G and toggles
between[Cto]and[oFF],thesoftwareisdetectingthattheoptionalanalog
output hardware is NOT installed.
Digital Span Selection For Bargraph Display
Decimal Point and Brightness Selection
Bargraph does not light
upforInputSignalsupto
3999 counts
Bargraph lights up for
InputSignalsabove
4000 counts
Bar
High
Bar
Low
Bar
High
Bar
Low
0
25 75
100
50
0
25 75
100
50
No bargraph display
Digital display
No bargraph display
Digital display
An example of setting the
digital span of the bargraph
display to be different than
the digital display range
The bargraph can be set to display full scale (0-101 bars) any portion
ofthedigitalreadingfromaminimumof100countstoamaximumof
12,000 counts. This provides higher resolution bargraph indication for
those applications where the normal operating input signal range is less
than the desired full scale display range of the digital display.
For Example:
If the full scale range of the meter has been set from -1999 to
9999 (0-12,000 counts), but the normal operating range of the
input signal is between 4000 & 6000. The bargraph high parame-
ter [bhi] can be set to 6000 and the bargraph low parameter [bLo]
can be set to 4000.
This means that although the meter could digitally display a signal
from -1999 to 9999 (0-12,000 counts), the bargraph display only
begins to function at a reading of 4000, and reaches full scale
indication at a reading of 6000. Although the digital display will
continue reading up to 9999 before indicating overrange, the bar-
graph display will indicate its overrange by flashing for readings
above 6000.

Page 6 CL-B101D40HZManual(d0098)
Example of Using the Center Point Bargraph Display Mode
with a Unipolar Input
If the meter's full scale range is set to 5000 counts, the midpoint would
be2500counts.Ifasignalof2500countsisappliedonlyonesegmentat
the2500countmarkwilllightup.Ifasignalof4000countsisappliedthe
segments between the center segment (2500 counts) and the 4000 count
marklightup.
Ifasignalof1000countsisapplied,thesegmentsbetweenthecenterseg-
ment(2500counts)andthe1000countmarkwilllightup.
Example of Using the Center Point Bargraph Display Mode
with Bipolar Signal Inputs
The meter may also be calibrated to display symmetrical bipolar signals such
as ± 1 V or ± 10 V. When the center point display mode is selected, it will
thenfunctionasacenterzerometer.Whenpositivesignalsareapplied,the
barwillgoupfromthecenterpoint,andwhennegativesignalsareapplied,
the bar will go down from the center point.
STEP E Selecting the [Anhi] Digital Value for Analog High Output
1) Using the and buttons, adjust the display to the desired
digitalvalueatwhichthe[chi]CalibratedAnalogHighoutputwill
occur.Fordigitalreadingsoutsidethedigitalspanselected,the
analogoutputwilllinearlyriseabovethevaluesetforchi,uptothe
maximumanalogoutputcapability.However,theanalogoutputwill
notgolowerthanthecalibratedvaluesetforcLo(seebelow).
2) Press the
P
button.Displaytogglesbetween[AnLo]and
previous[AnLo]setting.
STEP F Selecting the [AnLo] Digital Value for Analog Low Output
1) Using the and buttons, adjust the display to the desired
digitalvalueatwhichthe[cLo]CalibratedAnalogLowoutputwill
occur. ForDigitalreadingsoutsidetheDigitalSpanselected,the
analogoutputwillnotgolowerthanthecalibratedvaluesetfor
cLo.
2) Press the
P
button.Thedisplaytogglesbetween[cto]and
[oFF].
Note: Any two digital span points from –1999 to 9999 can be selected. The digital
valuesfor[Anhi]analoghighand[AnLo]analoglowcanbereversedtoprovidea20to
4mA output. The digital span selected can be as small as two counts, when using the
analogoutputtofunctionasaControlorAlarmDriver.Smalldigitalspanswillcause
the high resolution 16 bit D to A to increment digitally in stair case steps.
Digital Span Selection for Analog Range Output
Digital Span Selection for Analog Range Output
Bargraph Center Point Display Mode Selection
STEP G Bargraph Center Point Mode Selection (See example above)
1) To select bargraph center point mode, press the or
 button.Displaychangesfrom[oFF]to[on].
2) Press the
P
button.Displaytogglesbetween[diSP]and
 [on]or[oFF].
STEP H Digital Display ON/OFF Selection
 1) Tosetthedisplayto[oFF],pressthe or button.
 Displaytogglesbetween[diSP]and[oFF].
2) Press the
P
button.Thedisplayexitsthecalibrationmode
and returns to the operational display. Only the bargraph
display is on and the digital display is off.
Ifthedigitaldisplayisselectedtobeoff,pressinganybuttonto
makeprogrammingchangesortoviewsetpointsactivatesthedigitaldisplay.
When the procedure is complete, the digital display will then automatically
switch off.
The Display/Bargraph settings are now complete.
Operational Display
STEP G
STEP H
See Example of Bargraph
Center Point Display Mode
Selection Above
From Digital Span Selection
for Analog Range Output Above
or Direct From Decimal Point
and Brightness Selection Page 5
if Analog Output Option is Not Present
BARGRAPH CENTER POINT
DISPLAY MODE SELECTION
STEP E
STEP F
This branch will only
appear if the analog
output option is installed
To Bargraph Center
Point Display Mode
Selection Below
From Decimal Point and
Brightness Selection
See Page 5
DIGITAL SPAN SELECTION
FOR ANALOG RANGE OUTPUT
-1V +1V
0V
-1V +1V
0.800
-0.800
0V
-1V +1V
0V
Center Point
Single Bar Lit
Center Point
As signal
increases
Digital display
Digital display
Center Point
As signal
decreases
Digital display
05000
5000
2500
2500
4000
0
5000
2500
1000
0
Center Point
Single Bar Lit
Center Point
As signal
increases
Digital display
Digital display
Center Point
As signal
decreases
Digital display
Unipolar Signal Input Bipolar Signal Input

CL-B101D40HZ Manual (d0098) Page7
Operational Display
Sub-menu
MODE
STEP A Calibration
Mode
STEP B Calibration
Mode
STEP E
Calibrate
Analog
Output
Lo
STEP F
Calibrate
Analog
Output
Hi
Will only appear if the analog
output option is installed
To Digital Span Selection
for Bargraph Display
See Page 5
To Two Point Digital
Calibration Mode
See Page 4
Operational Display
TWO POINT ANALOG OUTPUT
RANGE SETTING AND CALIBRATION
+x
–x
4.00
+x
–x
20.00
Determine if the Analog Output Selection Header is in the 4 to 20mA (0-20mA) posi-
tionorthe0to10VDCposition.Ifnecessary,themodulemayhavetoberemoved
andtheheaderpositionchanged(seeComponentLayoutbelow).
Note:Alwaysdisconnectpowerfromthemeterbeforeremovingtheanalogoutputmod-
ule to adjust the mA or Volts output selection header and reinstalling it. When power is
reconnected, the meter’s software will automatically detect the presence or absence of
the analog output module.
STEP A Enter the Calibration Mode
1) Press the
P
and buttonsatthesametime.Displaytogglesbetween[cAL]
and[oFF].
2) Press the or button.Displaychangesfrom[oFF]to[on].
3) Press the
P
 button. Display toggles between [cAL] and [out] input
calibration.
Note:IfatthispointthedisplayskipsdirectlytotogglebetweenZeroandtheprevi-
ousZerosetting,thesoftwareisdetectingthattheoptionalanalogoutputhardware
is NOT installed.
STEP B Enter the Two Point Analog [ouT] Output Range Setting and Calibration
Mode
1) Press the
P
 button. Display toggles between [cLo] and an internal
scale factor.
STEP E SetorCalibrate[cLo]theLowAnalogValueoftheAnalogOutputRange
 1) Connectamultimetertoanalogoutputpins17and18(seeRearPanel
Pinouts on page 10). Using the and buttons, adjust the analog out-
puttothedesiredlowvalueasmeasuredonthemultimeter.cLomaybe
adjustedtoanyvaluefrom–0.3mAto18mA(mAoutputselected)orfrom
–0.6 V to 8 V (volt output selected).  However, the output of cLo must
alwaysbelessthanthevalueselectedforchi.Ifareversedanalogoutput
is desired, the values selected to establish the Digital Span can be
reversed(seetopofpage6).FordigitalreadingsoutsidetheDigitalSpan
selected,theanalogoutputwillnotgoanylowerthanthecalibratedvalue
setforcLo.However,theanalogoutputwilllinearlyriseabovethevalue
set for chi, up to the the maximum analog output capability (see chi
below).
2) Press the
P
 button. Display toggles between [chi] and an internal
scale factor.
STEP F SetorCalibrate[chi]theHighAnalogValueoftheAnalogOutputRange
1) Using the and buttons, adjust the analog output to the desired
highvalueasmeasuredonthemultimeterdisplay.chimaybeadjustedto
anyvaluefrom18mAto24mA (mAoutput)orfrom8Vto10.3V (volt
output).However,thevaluemustbehigherthanthevalueselectedforcLo.
FordigitalreadingsoutsidetheDigitalSpanselected,theanalogoutput
will linearly rise above the value set for chi, up to the maximum analog
output capability.
2) Press the
P
button.Themeterexitsthecalibrationmodeandreturns
to the operational display.
Note: The analog output range established by the values selected for cLo and chi will
occur,automaticallyscaled,betweenthetwodigitalvaluesselectedforAnHiandAnLo.
However, theanalogoutputcanlinearlyriseabovethechivaluesetfordigitalreadings
outside the digital span selected. See Digital Span Selection on page 6.
Two Point Analog Output Range Setting and Calibration
Two Point Analog Output Range Setting and Calibration
STEP I Select the Range
1) Using the and buttons, select the required range.
There are three ranges of 99.99Hz, 999.9Hz and 9999Hz
2) Press the
P
button.Thedisplayexitsthecalibration
mode and returns to the operational display.
The Display/Bargraph settings are now complete.
Two Point Analog Output Range Setting and CalibrationRange Selection Mode
Operational Display
From Bargraph Center Point
Display Mode Selection
on page 6RANGE SELECTION
Range
[99•99]
[9999]
[999•9]

Page 8 CL-B101D40HZManual(d0098)
Operational Display
SETPOINT SETTING
AND RELAY
CONFIGURATION MODE
STEP A
STEP B
STEP C
STEP D
No [doM] or [dob]
No [doM] or [dob]
STEP E
STEP F
STEP G
STEP H
STEP I
STEP J
STEP K
STEP L
To Step M of Setpoint
Setting and Relay
Configuration Page 9
Thefollowingprogrammingstepsarerequiredtoenterthesetpointvaluesandconfiguretherelayfunctions
in a meter with four relays using four setpoints. Generally if less than four relays are installed, the setpoints
withoutrelaysareoperationalinsoftwarefortri-colorcontrolordisplayonlypurposes.Toremoveunwanted
setpointindications,setthemto9999or-1999dependingontherelayactivationmodeselected.
STEP A Enter the Setpoint Mode
1) Press the
P
and buttonsatthesametime.Displaytogglesbetween[SP1]andtheprevious
SP1 setting.
STEP B Set Setpoint 1 [SP1]
1) Using the and buttons,adjustthedisplaytothedesiredSP1value.
2) Press the
P
button.Displaytogglesbetween[doM]andtheprevious[doM]setting.
STEP C Set the SP1 Delay-on-Make [doM] Delay Time Setting
1) Using the and buttons,adjustthedisplaytothedesired[doM]value(0to9999seconds).
The reading must continuously remain in an alarm condition until this delay time has elapsed before
therelaywillmakecontact(energize).
2) Press the
P
button.Displaytogglesbetween[dob]andtheprevious[dob]setting.
STEP D Set the SP1 Delay-on-Break [dob] Delay Time Setting
1) Using the and buttons,adjustthedisplaytothedesired[dob]value(0to9999seconds).
The reading must continuously remain in a non-alarm condition until this delay time has elapsed
beforetherelaywillbreakcontact(de-energize).
2) Press the
P
button.Displaytogglesbetween[hYSt]andtheprevious[hYSt]setting.
STEP E Select the Hysteresis [hYSt]
1) Using the and buttons,selecttheHysteresistobeONorOFF.
2) Press the
P
button.DisplaytogglesbetweenPUMand(on)or(oFF).
STEP F Select Pump [PUM] (on) or (oFF)
1) Using the and buttons,selectthePumptobeONorOFF.WhenPUMisselectedON,and
SP2issetatavaluehigherthanSP1,theSP1relaywilloperateinaspecial"pumponpumpoff"mode.
SP2 acts as the upper limit and SP1 acts as the lower limit of the Hysteresis Band on the SP1 relay.
For filling applications:
[rLYS]shouldbesetto[LhXX](seestepM).TheSP1relayandSP1LEDAnnunciatorwillthenactivateforinputs
less than the SP1 setpoint, and remain ON until the SP2 setpoint is reached.
For emptying applications:
[rLYS]shouldbesetto[hhXX](seestepM).TheSP1relayandSP1LEDAnnunciatorwillthenactivateforinputs
greater than the SP2 setpoint, and remain ON until the SP1 setpoint is reached.
2) Press the
P
button.Displaytogglesbetween[SP2]andthepreviousSP2setting.
STEP G Set Setpoint 2 (SP2)
1) Using the and buttons,adjustthedisplaytothedesiredSP2value.
2) Press the
P
button.Displaytogglesbetween[hySt]andtheprevious[hySt]setting.
STEP H Select the Hysteresis [hYSt]
1) Using the and buttons,selecttheHysteresistobeONorOFF.
2) Press the
P
button.Displaytogglesbetween[SP3]andtheprevious[SP3]setting.
STEP I Set Setpoint 3 (SP3) (No[doM]or[dob])
1) Using the and buttons,adjustthedisplaytothedesiredSP3value.
2) Press the
P
button.Displaytogglesbetween[hySt]andtheprevious[hySt]setting.
STEP J Select the Hysteresis [hYSt]
1) Using the and buttons,selecttheHysteresistobeONorOFF.
2) Press the
P
button.Displaytogglesbetween[SP4]andtheprevious[SP4]setting.
STEP K Set Setpoint 4 (SP4) (No[doM]or[dob])
1) Using the and buttons,adjustthedisplaytothedesiredSP4value.
2) Press the
P
button.Displaytogglesbetween[hySt]andtheprevious[hySt]setting.
STEP L Select the Hysteresis [hYSt]
1) Using the and buttons,selecttheHysteresistobeONorOFF.
2) Press the
P
button.Displaytogglesbetween[rLYS]andthepreviousrelaysetting.
Please Continue On Next Page.
Setpoint Setting and Relay Configuration Mode

CL-B101D40HZ Manual (d0098) Page 9
STEP M
STEP N
STEP O
STEP P
STEP Q
STEP R
STEP S
STEP T
STEP U
[orAn]
[rEd]
NOTE: Will only
appear if a tricolor
display is installed
[orAn]
[rEd]
[orAn]
[rEd]
[orAn]
[rEd]
[orAn]
[rEd]
BARGRAPH COLOR
PROGRAMMING MODE
Operational Display
Operational Display
From From Step L of
Setpoint Setting and Relay
Configuration Page 8
L or h
L or h
L or h
L or h
Tocomplywiththelatestsafetyrequirements,thetri-colorbargraphisdesignedlikeatrafficlight,to
display either red, orange or green, but only one color at a time. When the bar reaches a selected
color change point, the entire bar will change to the color designated for that zone. This eliminates any
ambiguity as to the signal status, especially just after transitioning to a new zone.
First (StepQ)istoselectthecolortobedisplayed,whenthebaris“below*”,whicheversetpointisset
to the lowest position.
Second (StepsR,S,T,andU)istoselectthecolortobedisplayedwhenthebarisaboveeachspecific
set point, regardless of the order or position to which the set points are set.
However,iftwoormoresetpointswithdifferentlyspecifiedcolorsarepositionedatthesamesetpoint
value,thecolorspecifiedforthesetpointwiththehighestidentifyingnumberwillbedisplayed.When
setpointsaresettothesamevalue,theSP4coloroverridestheSP3color,theSP3coloroverridesthe
SP2color,andtheSP2coloroverridestheSP1color.
STEP Q Select Bargraph Color when the bar is BELOW* the Setpoint that is set to the lowest
position
1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]
2) Press the
P
button.Displaytogglesbetween[CSP1]andthepreviouscolorsetting.
STEP R Select Bargraph Color when the bar is ABOVE* SP1 Setpoint
1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]
2) Press the
P
button.Displaytogglesbetween[CSP2]andthepreviouscolorsetting.
STEP S Select Bargraph Color when the bar is ABOVE* SP2 Setpoint
1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]
2) Press the
P
button.Displaytogglesbetween[CSP3]andthepreviouscolorsetting.
STEP T Select Bargraph Color when the bar is ABOVE* SP3 Setpoint
1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]
2) Press the
P
button.Displaytogglesbetween[CSP4]andthepreviouscolorsetting.
STEP U Select Bargraph Color when the bar is ABOVE* SP4 Setpoint
1) Using the and buttons,selectthedesiredbargraphcolor[grn],[oran]or[red]
2) Press the
P
button. Themeter exitsthesetpoint modeand returnstotheoperational
display.
The Bargraph Color programming mode is now complete.
STEP M Set Relay Activation mode [rLYS] for SP1
 (h)Hightherelayenergizeswhenthesetpointisexceeded.(L)Lowtherelayenergizesbelow
the setpoint. The setpoint is indicated from left to right SP1, SP2, SP3, SP4.
1) Using the and buttons, select (L) or (h) for the first digit, which corresponds to SP1.
2) Press the
P
button.TheSP2RelayActivationdigitbeginstoflash,anditsdecimalpointislit.
STEP N Set High (h) or Low (L) for SP2
1) Using the and buttons, select (L) or (h) for the second digit, which corresponds to SP2.
2) Press the
P
button.TheSP3RelayActivationdigitbeginstoflash,anditsdecimalpointislit.
STEP O Set High (h) or Low (L) for SP3
1) Using the and buttons, select (L) or (h) for the third digit, which corresponds to SP3.
2) Press the
P
button.TheSP4RelayActivationdigitbeginstoflash,anditsdecimalpointislit.
STEP P Set High (h) or Low (L) for SP4
1) Using the and buttons, select (L) or (h) for the fourth digit, which corresponds to SP4.
2) Press the
P
button.
Ifamono-colorredorgreendisplayisinstalledthentheSetpointRelayProgrammingModeisnowcompleteandthe
meter returns to the operational display.
IfatricolorbargraphdisplayisinstalledthentheBargraphColorProgrammingModewillbeenteredand
displaytogglesbetween[CoL]andtheprevioussetting.Colorselectionmenuwillbedisplayed.
Setpoint Setting and Relay Configuration Mode Continued
Bargraph Color Programming Mode

Page 10 CL-B101D40HZManual(d0098)
DIM
Lock
Analog Output
Hold
N/C
SP4
SP3
GND
+5 V
N/C
+ 5 V
SP1
4A
MOV
+ 5 V
SP2
4A
MOV
Display
Driver
Multiplexer
and
Buffer
Amplifier
Micro
Processor
100K
100K
0.1
0.1
Input Hi
Input Lo
+5VDC
-5VDC
+24VDC
Ref Hi
Analog Comm
System GND
MUXO
24 V Return
GND
+ 5 V
14 Bit
Single
Slope
A to D GND
+ 5 V
GND
+ 5 V
There are input
modules for almost
any input signal.
Input and Output
pins vary for
different modules.
Smart Modules
incorporate their own
A / D converters and
communicate digitally
with the meter.
See section on
I-Series Input Modules
for connection details.
INPUT MODULES
1
2
5
4
3
6
PROCESSOR BOARD
27
26
25
24
23
22
29
28
AC Neutral,
– DC
AC Line,
+ DC
14
8
9
10
11
15
Volts mA
HEADER
17
16
Chassis Ground Tab for Optional Metal Case
Socket for Input Signal
Conditioning Module
Common
Mode Line
Choke
Bridge
Rectifier
PTC for HI Voltage
Fuse for LO Voltage
Isolated Feed Back
Isolated
Switching
Power
Supply
Controller
-5 VDC
+18 VDC ISO
–
+5 VDC
+5 VDC
GND
+24 VDC
LC Filter
+
1
2
3
4
5
6
7
8
9
10
RELAY MODULES
NO3
COM 1 & 3
NO1
NC1
NO4
COM 2 & 4
NO2
NC2
MOV's
9A
4A
+ 5 V
SP3
+ 5 V
SP1
MOV's
9A
4A
+ 5 V
SP4
+ 5 V
SP2
- O/P
+ O/P
ANALOG
OUTPUT
+18V
ISO
+5VDC
Isolated
Analog
Output
Dual
or Single
ANALOG OUTPUT
MAIN BOARD
24V ISO RTN
GND
Output pins vary for different relay output modules.
August 13, 2002
CARRIER BOARD
1 3 5 7
2 4 6 8
9
10
LOCK
No Function
COMMON
DIM
DISPLAY BOARD
Relay Activation LEDs
Bargraph
Segments
Digital Display
Programming Buttons
Functional Diagram
Pinout Diagram
The Rear View of the Meter diagram shows the meter with the
relay configuration: dual 9 Amp Form C and dual 4 Amp Form
A relays� An analog output module is also shown as installed�
The CL-B101D40HZ uses plug-in type screw terminal connectors
for all input and output connections� The power supply connec-
tions (pins 14 and 15) have a unique plug and socket outline
to prevent cross connection� The main board and input signal
conditioner use right-angled connectors as standard� The output
module uses straight-thru connectors as standard�
Auto-sensing AC/DC power supply� For voltages between
85-265 V AC / 95-300 V DC (PS1) or 18-48 V AC / 10-72 V DC (PS2).
!
WARNING: AC and DC input signals and power supply
voltages can be hazardous. Do Not connect live wires to
screw terminal plugs, and do not insert, remove or handle
screw terminal plugs with live wires connected.
17 16
14 158 9 10 11
See Leopard Family Input
Signal Conditioning Modules
1 2 3 4 5 6
21 20 19
Relay Outputs Reserved for RS-485
LOCK
COMMON
No Function
DIM
ANALOG OUTPUT –
AC
Neutral
– DC
AC
Line
+ DC
ANALOG OUTPUT +
29 28 27 26 25 24 23 22
Standard plug-in screw terminal connectors provided by Texmate:
Connector Pinouts
Connector Pinouts
Input Signal – Pins 1 to 6
Pins 1 to 6 are reserved for the input signal conditioner�
See the data sheet for the selected input signal conditioner�
Pins 8 to 11 – Rear Panel Function Pins
Pins 8 to 11 provide functions that can be implemented
with an external switch. Their pin definitions are:
Pin 11 DIM. By connecting the display dim (DIM) pin to
the COMMON pin, the display brightness setting
is halved�
Pin 10 COMMON. To activate the LOCK or DIM
functions from the rear of the meter, the
respective pins have to be connected to the
COMMON pin� This pin is connected to the
internal power supply ground�
Pin 9 No function
Pin 8 LOCK. By connecting the LOCK pin to the
COMMON pin, the meter's programmed
parameters can be viewed but not changed�

CL-B101D40HZ Manual (d0098) Page 11
29 28 27 2526 24 23 22
DL Series
Options
4A
4A
Order Code
OR11
OR12
OR23
OR14
-
-
-
-
-
-
-
4A
4A
4A
4A
10A -
-
OR15
OR16
SP2 SP4 SP1 SP3
9A
9A
9A
9A
9A
9A
9A
9A
SP3SP1SP4SP2
Relay Modules with 2 Non-Isolated 4A Form A Relays,
and 2 Non-Isolated 9A Form C Relays
29 28 27 2526 24 23 22
DL Series
OptionsOrder Code
OR51
OR52
OR53
OR54
-
-
-
- -
-
210mA
210mA210mA
210mA210mA210mA
210mA210mA210mA210mA
SP4 SP3 SP2 SP1
SP4 SP3 SP2 SP1
Relay Modules with 4 Independent 300V
(210mA DC only)
29 28 27 2526 24 23 22
DL Series
OptionsOrder Code
OR31
OR32
OR33
OR34
-
-
-
- -
-
5A5A 5A 5A
5A 5A
5A
5A
5A
5A
SP4 SP3 SP2 SP1
SP1SP2SP3SP4
Relay Modules with 4 Isolated 5A Form A Relays
Output
Carrier
Board
Output
Carrier
Board
Relay
Module
Relay
Module
Input Signal
Conditioner
Analog Output
Module
Main
Board
Display
Board
Component Layout
Component Layout
Connector Pinouts continued
AC/DC Power Input- Pins 14 and 15
Auto-sensing AC/DC power supply� For voltages between
85-265 V AC/95-300 V DC (PS1) or 18-48 V AC/10-72 V DC (PS2).
Pin 14 AC/DC Neutral. Neutral power supply line�
Pin 15 AC/DC line. Live power supply line�
Optional Carrier Board Output Pins
Analog Output- Pins 16 and 17
Pins 16 and 17 are the analog output pins on the optional
output module� Their pin definitions are:
Pin 16 Positive (+) analog output�
Pin 17 Negative (–) analog output�
RS-485 Output- Pins 19, 21 and 21
Pins 22 to 29 – Output Module Pins

Page 12 CL-B101D40HZManual(d0098)
Unless otherwise specified Texmate will ship all modules
pre-calibratedwithfactorypreselectedrangesand/orscal-
ings as shown in BOLD type. Other pre-calibrated standard
rangesorcustomrangesmaybeordered.Factoryinstalled
customscalingandothercustomoptionsarealsoavailable
(seeOrderingInformation,SpecialOptionsonlastpage).
WARNING: AC and DC input signals and power supply
voltages can be hazardous. Do Not insert, remove or handle
modules with live wires connected to any terminal plugs.
!
I-Series Input Signal Conditioning Modules
COUPLING
INPUT SIGNAL FILTER
MAG NAMUR SOURCE SINK
LOAD
AC
20KHz
2KHz
200Hz
OFF
DC
MAG/AC
LOGIC
GND
+24V
INPUT
High Accuracy Digital Measurement
NPN
Open Collector
Proximity Switch
Normally Pin 1 is at 24V
When sensor is activated Pin 1 goes to 0V
Using NPN Open Collector Proximity Switch 330B
IF05: Universal Frequency / RPM
IF05 RPM
Low-pass Filter Header
20 kHz, 2kHz, 200Hz
Signal Type Header
AC, mV or digital logic
Sensor Header
Mag, Namur,
Source, and Sink
De-coupling Header
20 mHz high pass lter
Please go to IF05 input module data sheet for more detail
https://www.texmate.com/media/pdf/2018/09/Texmate_IF05.pdf
IF08: Line Frequency
INPUT LO
INPUT HI
60 to 500V AC
BL-40F
DL-40F
FL-B101D40F
LEOPARD
High Accuracy Digital Frequency Measurement
316A

CL-B101D40HZ Manual (d0098) Page 13
101.60
4.000
42.85
1.687
42.85 1.687
42.85 1.687
42.85
1.687
6.50
0.256
113.79
4.480
113.79
4.480
56.90 2.240
56.90 2.240
17.50
0.689
97.77
3.849
119.70
4.713
13.70
0.539
1/4"-28UNF
Panel Cutout
5.0
0.197
R4
0.157
16.30
0.642
13.70
0.539
4.80
0.189
screw-10-32 UNF
8
0.315
7
0.276
16.30
0.642
13.70
0.539
2.60
0.102
6.32
0.249
screw-1/4”-28 UNF
Case Dimensions
Installation Guidelines
Installation
1� Install and wire meter per local applicable codes/reg-
ulations, the particular application, and good installation
practices�
2. Install meter in a location that does not exceed the
maximum operating temperature and that provides
good air circulation�
3. Separate input/output leads from power lines to
protect the meter from external noise. Input/output
leads should be routed as far away as possible from
contactors, control relays, transformers and other noisy
components� Shielding cables for input/output leads is
recommended with shield connection to earth ground
near the meter preferred�
4� A circuit breaker or disconnect switch is required to
disconnect power to the meter� The breaker/switch
should be in close proximity to the meter and marked as
the disconnecting device for the meter or meter circuit�
The circuit breaker or wall switch must be rated for the
applied voltage (e�g�, 120VAC or 240VAC) and current
appropriate for the electrical application (e�g�, 15A or
20A)�
!
5� See Case Dimensions section for panel cutout infor-
mation�
6� See Connector Pinouts section for wiring�
7. Use 28-12 AWG wiring, minimum 90˚C (HH) tempera-
ture rating. Strip wire approximately 0.3 in. (7-8 mm).
8� Recommended torque on all terminal plug screws is
4�5 lb-in (0�51 N-m)�

BASIC MODEL # DISPLAY POWER SUPPLY INPUT MODULES ANALOG OUTPUT RELAY OUTPUT OPTIONS / ACCESSORIES
OA____
Page 14 CL-B101D40HZManual(d0098)
CL-B101D40HZ
Add to the basic model number the order code suffix for each standard option required. The last suffix is to
indicate how many different special options and or accessories that you may require to be included with this product.
Ordering Example: CL-B101D40HZ-VRR-PS1-IF08-OIC-R11-OA1 (Range Change)
Ordering Information
WARRANTY
Texmatewarrantsthatitsproductsarefreefromdefectsinmaterialandworkmanshipunder
normaluseandserviceforaperiodofoneyearfromdateofshipment.Texmate’sobligations
under this warranty are limited to replacement or repair, at its option, at its factory, of any of
theproductswhichshall,withintheapplicableperiodaftershipment,bereturnedtoTexmate’s
facility, transportation charges pre-paid, and which are, after examination, disclosed to the
satisfactionofTexmatetobethusdefective.Thewarrantyshallnotapplytoanyequipment
which shall have been repaired or altered, except by Texmate, or which shall have been
subjectedtomisuse,negligence,oraccident.InnocaseshallTexmate’sliabilityexceedthe
original purchase price. The aforementioned provisions do not extend the original warranty
periodofanyproductwhichhasbeeneitherrepairedorreplacedbyTexmate.
USER’S RESPONSIBILITY
We are pleased to offer suggestions on the use of our various products either by way of
printedmatterorthroughdirectcontactwithoursales/applicationengineeringstaff.However,
sincewehavenocontrolovertheuseofourproductsoncetheyareshipped,NOWARRANTY
WHETHER OF MERCHANTABILITY, FITNESS FOR PURPOSE, OR OTHERWISE is made
beyondtherepair,replacement,orrefundofpurchasepriceatthesolediscretionofTexmate.
Users shall determine the suitability of the product for the intended application before using,
and the users assume all risk and liability whatsoever in connection therewith, regardless
ofany ofoursuggestions orstatements astoapplicationorconstruction. Inno eventshall
Texmate’sliability,inlaworotherwise,beinexcessofthepurchasepriceoftheproduct.
Texmatecannot assume responsibilityforanycircuitrydescribed.No circuitpatent orsoft-
warelicensesareimplied.Texmatereservestherighttochangecircuitry,operatingsoftware,
specifications, and prices without notice at any time.
1934 Kellogg Ave., Carlsbad, CA 92008
Tel: [phone] • 1-800-TEXMATE
Fax: [phone] • Email: [email protected]
BASIC MODEL NUMBER
CL-B101D40HZ 114x114mm, 101 Segment Circular Bargraph with 4 Digit
Display .........................................$595
Standard Options for this Model Number
Order Code Suffix Description List
DISPLAY
RR......Red Circular 101 Segment LED Bar with 4 Digit Red LED Display ........N/C
GR ... Green Circular 101 Segment LED Bar with 4 Digit Red LED Display ..... $15
TR ......Tri-Color Circular 101 Segment LED Bar with 4 Digit Red LED Display .... $50
POWER SUPPLY
PS1 .....85-265VAC/95-300VDC ...........................................N/C
PS2 .....18-48VAC/10-72VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $40
INPUT MODULES (Partial List. See www.texmate.com)
Unless otherwise specified Texmate will ship all modules precalibrated with
factory preselected ranges and/or scalings as shown in BOLD type.
IF05....Universal Frequency / RPM ...............................
IF08.....Line Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $167
ANALOG OUTPUT
Note: If a meter is ordered with a Analog Output and/or Relay Output
Module, an Output Module Carrier Board will be automatically added
to the order.
OIC .....Isolated 16 Bit Current Output, 4-20mA ............................... $46
OIV .....Isolated 16 Bit Voltage Output, 0-10VDC .............................. $46
SA-CLCB Output Module Carrier Board ....................................... $30
RELAY OUTPUT MODULES
Note: If a meter is ordered with a Analog Output and/or Relay Output
Module, an Output Module Carrier Board will be automatically added
to the order.
SA-CLCB �������������������������������������������������
Output Module Carrier Board ����������������������������������$30
OR11 � One 10 Amp Form C Relay, Isolated ���������������������$41
OR15 � One 10 Amp Form C and Two 5 Amps Form A Relays �������$99
OR16 � One 10 Amp Form C and One 5 Amp Form A Relays ��������$76
OR12 � Two 10 Amp Form C Relays, Isolated ��������������������$81
OR14 � Two 10 Amp Form C and Two 5 Amps Form A Relays �������$139
OR23 � Two 10 Amp Form C and One 5 Amp Form A Relay, Isolated��$116
OR25 � One 9A Form C & two 4A Form A relays� Isolated� ����������$99
OR31 � One 5 Amp Form A Relay, Isolated ����������������������$35
OR32 � Two 5 Amp Form A Relays, Isolated ���������������������$70
OR33 � Three 5 Amp Form A Relays, Isolated ��������������������$94
OR34 � Four 5 Amp Form A Relays, Isolated ���������������������$123
CL-B101D40HZ Technical Manual Copyright © 2020 Texmate Inc. All rights
reserved. Published by: Texmate Inc. USA. Information in this Technical Manual
is subject to change without notice due to correction or enhancement. The
information described in this manual is proprietary to Texmate, Inc. and may
not be copied, reproduced or transmitted, in whole or in part, in connection with
the design, manufacture, or sale of apparatus, device or private label product
without the express written consent of Texmate, Inc.
Solid State Relay (SSR) Output Modules DC Only
OR51 � One 400V DC Solid State Relay (SSR) 210mA�������������$35
OR52 � Two 400V DC Solid State Relays (SSR) 210mA ������������$70
OR53 � Three 400V DC Solid State Relays (SSR) 210mA�����������$94
OR54 � Four 400V DC Solid State Relays (SSR) 210mA ������������$ 123
Special Options and Accessories
Part Number Description List
SPECIAL OPTIONS (Specify Inputs or Outputs & Req. Reading )
ZR ............... Range change from Standard Range shown in BOLD Type .......$20
ZS ............... Custom Digital Display Scaling within Stadard Ranges ...........$24
CS-BAR .......... Custom Bargraph Display Scaling within Standard Range .........$17
ZS-AO............ Custom Scaling of Analog Output ...........................$35
ART-FS1 .......... Produce and install custom faceplate per meter - 1 color .........$55
ART-FS2 .......... Produce and install custom faceplate per meter - 2 color .........$60
ART-FS3 .......... Produce and install custom faceplate per meter - 3 color .........$65
ART-FS4 .......... Produce and install custom faceplate per meter - 4 color ........$69
ART-NRC-DEC ..... NRC for Artwork & set-up Custom Faceplate and/or Descriptor ....$100
ACCESSORIES (Specify Serial # for Custom Artwork Installation)
93-PLUG2P-DP...... Extra Screw Terminal Conn., 2 Pin Power Plug ............... $3
93-PLUG2P-DR ..... Extra Screw Terminal Conn., 2 Pin Plug..................... $3
93-PLUG3P-DR ..... Extra Screw Terminal Conn., 3 Pin Plug..................... $5
93-PLUG4P-DR ..... Extra Screw Terminal Conn., 4 Pin Plug..................... $6
93-PLUG5P-DR ..... Extra Screw Terminal Conn., 5 Pin Plug..................... $7
Prices subject to change without notice