Texmate Leopard series User manual

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comApr-23-2009 FL-B101D40 DS (FL7) Page 1

Now featuring New Version 2.0 software

with one-color Brightness control, this smart

Tricolor or Mono-color digital bargraph has four

fully programmable set points for monitoring,

measurement, and control applications.

• External transmitters or signal conditioners can be eliminated

by direct connection of the sensor output to more than

40 Plug-in Input Signal Conditioners that include:

– AC/DC Current – Pressure – Resistance

– AC/DC Voltage – Process – Temperature

– Load Cell – Prototype – 4 to 20 mA

• Optional isolated 16 bit analog output. User or factory scal-

able to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any

desired digital span from ± one count to the full scale range

of – 1999 to 9999 (12000 counts).

• A Programmable Tricolor (Red-Green-Orange) or mono

color (red or green), 101 segment high brightness bargraph.

Vertical or optional horizontal format.

• Red 4-digit LED display with a range of -1999 to 9999

(12000 counts). Optional green digital display.

• Front panel LED annunciators provide indication of setpoint

status.

• Two 10 Amp Form C, and two 5 Amp Form A relays available

• Auto-sensing AC/DC power supply. For voltages between

85-265 V AC / 95-370 V DC (PS1) or 18-48 V AC / 10-72 V

DC (PS2).

• 24 V DC excitation is available to power external 4/20mA

transmitters and 5 or 10 V DC excitation is available for

resistance bridge type sensors.

• Provision to connect an external programming lockout switch.

• Provision for external DIM switch to reduce the brightest

display setting by 50%.

• Optional NEMA-4 front cover.

• Automatic intelligent averaging, smooths noisy signals while

providing a fast display response to real level changes.

Input Specs: ..............Depends on Input signal conditioner

A/D Converter:...........14 bit single slope

Accuracy:...................±(0.05% of reading + 2 counts)

Temp. Coeff.:.............100 ppm/°C (Typical)

Warm up time:...........2 minutes

Conversion Rate: ......10 conversions per second (Typical)

Digital Display:..........

4 digit 0.31" LED red (std), green (optn)

Range

–1999 to 9999 counts.

Bargraph Display:.....

101 segment 4” red vertical (std),

green or tricolor (optn), horizontal (optn)

Polarity:......................Assumed positive. Displays – negative

Decimal Selection:....Front panel button selectable, X•X•X•X•

Positive Overrange:..Bargraph and top segments of digital

display flash.

Negative Overrange:.First segment of bargraph and bottom

segments of digital display flash.

Relay Output: ............Two 5 Amp Form A relays and Two

10 Amp Form C relays.

Analog Output:..........Isolated 16 bit user scalable mA or V

OIC (mA out)...........

4-20 mA @ 0 to 500Ωmax loop resistance

OIV (volts out).......... 0-10 V DC @ 500 Ωor higher resistance

Power Supply:...........AC/DC Auto sensing wide range supply

PS1 (std) ................

85-265 VAC / 95-370 VDC @ 2.5W max 4.2W

PS2 .........................

18-48 VAC / 10-72 VDC @ 2.5W max 4.2W

Operating Temp.:.......0 to 60°C

Storage Temp: ...........–20°C to 70°C

Relative Humidity: ....95% (non condensing)

Case Dimensions:.....

9/64 DIN (Bezel 36Wx144Hmm)

Depth behind bezel (5.83") 148mm

Plus (0.7”) 18mm for connectors

Weight:.......................9.5 oz., 12 oz when packed

General Features Input Module Compatibility

Specifications

Index

LEOPARD FAMILY

FL-B101D40

Leopard Bargraph Meter

101 Segment, 4 Digit 0.32” LEDs

in a 9/64 DIN CASE

• The bargraph can display, full

scale, any desired portion of

the digital reading.

•

Bargraph center zero function.

•

Four programmable setpoints

with adjustable Hysteresis.

• Setpoint 1 has delay-on-

make and delay-on-break

plus a special “pump on

pump off” mode that creates

Software Features

a Hysteresis Band between

SP1 and SP2.

• Relay activation can be

selected to occur above (hi)

or below (Lo) each setpoint.

• Digital display blanking.

• Decimal point setting.

• Four-level brightness control

accessed by the button

and adjusted by the

button.

Bargraph Center Point Display Mode Selection . . 6

Bargraph Color Programming Mode . ...... 9

CaseDimensions....................... 7

Component Layout . ................... 11

Connector Pinouts . ................... 10

Connectors . ......................... 11

Controls and Indicators . ................ 2

Custom Faceplates and Scales . ......... 19

Decimal Point and Brightness Selection . . . . 5

Programming Conventions . . . . . . . . . . . . . . . 2

Setpoint Setting & Relay Configuration Mode . . 8-9

SoftwareFeatures...................... 1

Software Logic Tree . . . ................. 3

Specifications . ........................ 1

Standard Faceplates and Scales . . . . . . . . . 18

Two Point Analog Range Setting & Calibration. . . 7

Two Point Digital Calibration Mode . ....... 4

Digital Span Selection for Display . . . ...... 5

Digital Span Selection for Analog Range Output . 6

Functional Diagram . . . . . . . . . . . . . . . . . . . . 10

GeneralFeatures....................... 1

I-Series Input Signal Conditioning Modules . . 12-15

Input Module Calibration Procedures . ... . 17

Input Module Component Glossary . . . . . . . 16

Ordering Information . . . . . . . . . . . . . . . . . . . 20

Pin Descriptions . ..................... 10

Version 2.0

LEOPARD

✔LEOPARD FAMILY: More than 38 different

Plug-in I-Series Input Signal Conditioners are

approved for Texmate’s Leopard Family of meters.

Some examples are shown on pages 12 - 15.

See www.texmate.com for an up to date listing.

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 2 Apr-23-2009 FL-B101D40 DS (FL7)

Front Panel Buttons

Program Button

The

button is used to move from one program step to the next.

When pressed at the same time as the button, it initiates the

calibration mode.When pressed at the same time as the button,

it initiates the setpoint setting mode.

Button

DOWN

Button

PROGRAM

Button

LED

Annunciators

for Setpoints

1-4

Seven Segment

LED Display

101 Segment

Bargraph

Up Button

When in the operational display, pressing the button allows you

to view the setting of the saved Peak and Valley Values.

When setting a displayed parameter during programming, the

button is used to increase the value of the displayed parameter.

Down Button

When in the operational display, pressing the button allows you

to change the Brightness Level as well as to view the setting of

the setpoints SP1, SP2, SP3 & SP4.

When setting a displayed parameter during programming, the

button is used to decrease the value of the displayed parameter.

Front Panel LED Display

Annunciator LEDs

The annunciator LEDs indicate the alarm status. They are labeled

from bottom to top: SP1, SP2, SP3, SP4.

Digital LED Displays

The digital LED displays are used to display the meter input

signal readings. They also display the programming settings

during programming.

Setpoint Indication

The position of setpoints on the bargraph display are indicated by

an ON or OFF segment dependent on the bargraph display being

above or below the setpoint.

Setpoints

indicated

by an ON

Segment

Setpoints

indicated

by an OFF

Segment--

Controls and Indicators

This symbol represents the

OPERATIONAL DISPLAY.

This is the PROGRAM button.

This is the UP button.

This is the DOWN button.

When a button is shown, press and release

it to go onto the next step in the direction

indicated by the arrow. When an alterna-

tive dotted line is shown, this indicates that

an alternative logic branch will be followed

when a particular option is present.

When two buttons are shown side by

side and enclosed by a dotted line, they

must be pressed at the same time then

released to go onto the next programming

step.

If an X appears through a digit, it means

that any number displayed in that digit is not

relevant to the function being explained.

[Span]

[10000]

When the

and

buttons are shown

together, the display value can be increased

by pressing and releasing the

button

or decreased by pressing and releasing the

button.

When the

and

buttons are shown

with two displays, either display can be

selected by pressing and releasing the

buttons.

When two displays are shown together

with bursts, this indicates that the display is

toggling (flashing) between the name of the

function and the value.

Text or numbers shown between square

brackets in a procedure indicate the pro-

gramming code name of the function or the

value displayed on the meter display.

When there are more than two display selec-

tions they are shown in brackets below the

first display and are also selectable by press-

ing and releasing the

buttons.

A dotted line enclosing an entire logic dia-

gram indicates that programming branch

will appear only when a particular option is

present.

To explain software programming procedures, logic diagrams are

used to visually assist in following the programming steps. The

following symbols are used throughout the logic diagrams to

represent the buttons and indicators on the meter:

Programming Conventions

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comApr-23-2009 FL-B101D40 DS (FL7) Page 3

The FL-B101D40 is an intelligent bargraph meter with a hierarchi-

cal software structure designed for easy programming and opera-

tion, as shown below in the software logic tree.

Software Logic Tree

Peak

[PEAK]

Reset

PEAK

Reset

VALY

Valley

[VALY]

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

See Page 9

Tricolor Bargraph

The tri-color bargraph is

designed like a traffic light, to

display either red, orange or

green, but only one color at a

time. The color to be displayed is

selected in two ways.

The first step is to select the

color to be displayed when the

bar is “below” whichever set

point is set to the lowest

position.

The second step is to select the

color to be displayed when the

bar is above each specific

setpoint, regardless of the order

or position to which the set

points are set.

However, if two or more

setpoints with differently

specified colors are positioned

at the same set point value, the

color specified for the set point

with the highest identifying

number will be displayed. When

setpoints are set to the same

value, the SP4 color overrides

the SP3 color, the SP3 color

overrides the SP2 color, and the

SP2 color overrides the SP1

color.

Set Setpoint 1

[SP1]

Delay-on-Make

[doM]

Delay-on-Break

[dob]

Relays

Activation

[rLYS]

(h) High the

relay

energizes

when the

setpoint is

exceeded.

(L) Low

the relay

energizes

below the

setpoint.

Setpoint 2

[SP2]

Setpoint 2

[SP2]

Setpoint 1

[SP1]

Setpoint 3

[SP3]

NOTE: [dom] [dob]

Functions are only

available for SP1

0 to 9999

seconds

0 to 9999

seconds

Pump

[PUM]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Bar Color

[coL]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Setpoint 3

[SP3]

Setpoint 4

[SP4]

Setpoint 4

[SP4]

Operational Display

MAIN MENU

PEAK & VALLEY

VIEW & RESET

BRIGHTNESS AND

SETPOINT VIEW MODE

Bargraph Center Point

Display Selection [cto]

This branch will

only appear if

the analog

output option

is installed

Back to

Operational

Display

Digital Display

ON/OFF

Selection [diSP]

Sub-menu MODE

Calibration Mode

Calibration

Input

Calibration

Output

Calibrate Analog

Output Low

[cLo]

Calibrate Analog

Output High

[chi]

Select the Digital

Reading at which

the Analog Output

Hi [chi] will occur

Select the Digital

Reading at which

the Analog Output

Lo [cLo] will occur

This branch will only appear

if the analog output option

is installed

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

See Page 6

DIGITAL DISPLAY ON/OFF

See Page 6

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

See Page 6

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

See Page 7

Set the Decimal

Point [dp]

Bargraph Display

Scale Lo Range

Setting [bLo]

Bargraph Display

Scale hi Range

Setting [bhi]

Display

Brightness [br]

1 Dimmest

2 Dim

3 Bright

4 Brightest

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

DECIMAL POINT AND

BRIGHTNESS SELECTION

See Page 5

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

See Page 5

Select the

desired

reading for

the applied

Lo input

signal

Select the

desired

reading for

the applied

hi input

signal

Any new settings

are canceled and

previous settings

are retained

Err. Indicates

unsuccessful

calibration

Goes directly

to Zero setting

if Analog Output

is not installed

TWO POINT DIGITAL

CALIBRATION MODE

See Page 4

–

4.00

–

20.00

1 Dimmest

2 Dim

3 Bright

4 Brightest

SETPOINT SETTING AND

RELAY CONFIGURATION MODE

See Page 8

L or h

Display

Brightness

[br]

Pump On Pump Off

When PUM is selected ON,

and SP2 is set at a value

higher than SP1, the SP1

relay will operate in

a special "pump on pump off"

Hysteresis mode. SP2 acts

as the upper limit and SP1

acts as the lower limit of the

Hysteresis Band.

For filling applications, rLYS

should be set to LhLh. SP1 will

then activate for inputs less than

the SP1 setpoint, and remain

ON until the SP2 setpoint is

reached.

For emptying applications,

rLYS should be set to hhhh.

SP1 will then activate for inputs

greater than the SP2 setpoint,

and remain ON until the SP1

setpoint is reached.

Software Version is Displayed on Power-up

When power is applied, all segments of the bargraph and digi-

tal display light up for 3 seconds. The version number of the

installed software is then displayed for 2 seconds, after which,

the operational display indicates the input signal.

15 Second Program Timeout

Except for ZERO and SPAN settings in the Two Point Digital Calibration Mode

and the Analog Output Range Setting and Calibration Mode (cLo and chi), the

meter has a 15 second program timeout. If no buttons are pressed for 15 sec-

onds in any of the other programming sequences, the meter will exit the pro-

gramming mode and return to the operational display. Any program changes

that were made prior to pressing the

button in the preceding step will not be

saved.

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 4 Apr-23-2009 FL-B101D40 DS (FL7)

STEP A Enter the Calibration Mode

Press the

and buttons at the same time. Display toggles

between [CAL] and [oFF].

2) Press the or button. Display changes from [oFF] to [on].

Press the

button. Display toggles between [CAL] and [out].

Note: If at this point, the display skips directly to STEP C and toggles between

[SPAn] and the previous [SPan] setting, the software is detecting that the

optional analog output hardware is NOT installed.

STEP B

Select Two Point Digital Calibration of Input Signal

1) Press the or button to select CAL

[iP] for input signal calibra-

tion.

2) Press the

button. Display toggles between [ZEro] and the previ-

ous zero setting.

STEP C Set the Meter’s Low Input Signal Reading on the Digital Display

1) Apply a zero or low signal to the meter. (Positive or negative val-

ues are allowed).

2) Using the and buttons, adjust the meter display to the

desired reading for the applied low input signal.

3) Press the

button. Display toggles between [SPAn] and the pre-

vious span setting.

STEP D Set the Meter’s High Input Signal Reading on the Digital Display

1) Apply a high input signal to the meter.

2) Using the and buttons, adjust the digital display to the

desired reading for the applied high input signal.

3) Press the

button.

The Digital Calibration Procedure is now complete.

If the digital calibration was successfully completed, the menu branches

to the Digital Span Selection for Bargraph Display (see page 5), and the

display flashes [bhi] and the previous setting.

ERROR Indicates Unsuccessful Calibration

If the calibration was unsuccessful, the display indicates [Err], the new

calibration settings just entered will not take effect and the previously

stored setting will remain.

The three most likely causes of an error during

calibration are:

The full scale and zero signals were too similar. The full scale signal must be

at least 1000 counts greater than the zero or low input signal (positive and

negative values are allowed).

2. The scaling requirement exceeded the digital display span capability

of the meter (12,000 counts between –1999 to 9999).

3. No input signal present, or incorrect input signal connections.

This mode enables the meter to be calibrated by applying a zero or low input signal, entering the desired reading for that signal, then

applying a high input signal, and then entering the desired reading for that signal. The meter then automatically calculates and pro-

grams in the requisite scale factor, within the following parameters.

1. Positive and negative signals may be applied, but the difference between the low and the high signal inputs must be at least 1000

counts or Err will be indicated.

2. Positive and Negative values for the desired reading can be entered, but the scale factor created can not exceed the Digital Display

Span capability of the meter which is 12,000 counts between –1999 to 9999.

3. The internal Signal Span is limited to 3 V DC between – 1 V DC to + 2 V DC. Any outputs from an Input Signal Conditioning module

that exceed these limits will cause the meter to indicate overrange regardless

of the Digital Display Span scaled.

Note: Many input signal conditioners have provisions for analog calibration and

scaling. If the meter is digitally set to read zero with a zero input (shorted input),

and to read 1000 with a 1.000 V input, any pre-calibrated analog signal con-

ditioner, with an output that does not exceed – 1 V to + 2 V, will read correctly

without any further calibration when it is inserted in the meter.

Two Point Digital Calibration Mode

MAIN MENU

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP C Zero

STEP D Span

Err. Any new setting

canceled and previous

settings are retained

To Digital Span Selection for

Bargraph Display Page 5

cAL out/iP branch will only

appear if the analog output

option is installed, otherwise

cAL on goes directly to ZEro

setting

TWO POINT DIGITAL

CALIBRATION MODE

To Digital Span Selection

for Bargraph Display

See Page 6

To Two Point Analog

Output Range Setting

and Calibration

See Page 7

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comApr-23-2009 FL-B101D40 DS (FL7) Page 5

Example

From Two Point

Digital Calibration

Mode See Page 4

STEP A

STEP B

STEP C

STEP D

See Example Above

of Bargraph Display

Scale Range

To Digital Span Selection

for Analog Range Output or

Bargraph Center Point

Display Mode Selection

on Page 6

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

DECIMAL POINT AND

BRIGHTNESS SELECTION

STEP A Enter the Calibration Sub Menu Mode

1) Press the

and buttons at the same time. Display toggles

between [CAL] and [oFF].

2) Press the

button. Display toggles between [bhi] and the

p r e v i o u s setting.

STEP B Set the Digital Span of the Bargraph Display

(See example

above)

1) Using the and buttons, adjust the display to the desired

high parameter reading, e.g. 6000 counts.

2) Press the

button. Display toggles between [bLo] and the

previous setting.

3) Using the and buttons, adjust the display to the desired

low parameter reading, e.g. 4000 counts.

4) Press the

button. Display changes from [4000] to [dP].

STEP C Set the Decimal Point

1) Using the and buttons, adjust the display to the desired

decimal point setting.

2) Press the

button. Display toggles between [br] and the

previous brightness setting.

STEP D Set the Bargraph and Digital Display Brightness

1) Using the and buttons, adjust the display to the desired

brightness setting (4 is the brightest setting).

2) Press the

button. Display toggles between [Anhi] and the

previous [Anhi] setting.

Note: If at this point, the display skips directly to STEP G and toggles

between [Cto] and [oFF], the software is detecting that the optional analog

output hardware is NOT installed.

Digital Span Selection For Bargraph Display

Decimal Point and Brightness Selection

Bargraph does not light up for

Input Signals up to 3999 counts

Bargraph lights up for Input

Signals above 4000 counts

No bargraph

display

Digital display Digital display

100

Bargraph display

ends at

6000 counts

Bargraph display

starts at

4000 counts

At 5000 counts

the bargraph display

will be at midpoint

100

Example of Setting the Digital Span of the Bargraph Display

to be Different than the Digital Display Range

The bargraph can be set to display full scale (0-101 bars) any portion

of the digital reading from a minimum of 100 counts to a maximum of

12,000 counts. This provides higher resolution bargraph indication for

those applications where the normal operating input signal range is less

than the desired full scale display range of the digital display.

For Example:

If the full scale range of the meter has been set from -1999 to

9999 (0-12,000 counts), but the normal operating range of the

input signal is between 4000 & 6000. The bargraph high param-

eter [bhi] can be set to 6000 and the bargraph low parameter [bLo]

can be set to 4000.

This means that although the meter could digitally display a signal

from -1999 to 9999 (0-12,000 counts), the bargraph display only

begins to function at a reading of 4000, and reaches full scale

indication at a reading of 6000. Although the digital display will

continue reading up to 9999 before indicating overrange, the bar-

graph display will indicate its overrange by flashing for readings

above 6000.

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 6 Apr-23-2009 FL-B101D40 DS (FL7)

5000

Center

Point

Single

Bar Lit

2500

5000

Center

Point

2500

4000

As signal

increases

5000

Center

Point

2500

1000

As signal

decreases

+ 1 V

Center

Point

Single

Bar Lit

- 1 V

0 V

+ 1 V

Center

Point

- 1 V

0 V

0.800

As signal

increases

+ 1 V

- 1 V

0 V

Center

Point

-0.800

As signal

decreases

Example of Using the Center Point Bargraph Display Mode

with a Unipolar Input

If the meter's full scale range is set to 5000 counts, the midpoint would be

2500 counts. If a signal of 2500 counts is applied only one segment at the

2500 count mark will light up. If a signal of 4000 counts is applied the seg-

ments between the center segment (2500 counts) and the 4000 count mark

light up.

If a signal of 1000 counts is applied, the segments between the center seg-

ment (2500 counts) and the 1000 count mark will light up.

Example of Using the Center Point Bargraph Display Mode

with Bipolar Signal Inputs

The meter may also be calibrated to display symmetrical bipolar signals such

as ± 1 V or ± 10 V. When the center point display mode is selected, it will then

function as a center zero meter. When positive signals are applied, the bar

will go up from the center point, and when negative signals are applied, the

bar will go down from the center point.

STEP E Selecting the [Anhi] Digital Value for Analog High Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [chi] Calibrated Analog High output will

occur. For digital readings outside the digital span selected, the

analog output will linearly rise above the value set for chi, up to the

maximum analog output capability. However, the analog output will

not go lower than the calibrated value set for cLo (see below).

2) Press the

button.

Display toggles between [AnLo] and previous

[AnLo] setting.

STEP F Selecting the [AnLo] Digital Value for Analog Low Output

Using the and buttons, adjust the display to the desired

digital value at which the [cLo] Calibrated Analog Low output will

occur. For Digital readings outside the Digital Span selected, the

analog output will not go lower than the calibrated value set for cLo.

Press the

button. The display toggles between [cto] and [oFF].

Note: Any two digital span points from –1999 to 9999 can be selected. The digital

values for [Anhi] analog high and [AnLo] analog low can be reversed to provide a 20 to

4mA output. The digital span selected can be as small as two counts, when using the

analog output to function as a Control or Alarm Driver. Small digital spans will cause

the high resolution 16 bit D to A to increment digitally in stair case steps.

See Two Point Analog Output Range Setting and Calibration at the top of the next page.

Digital Span Selection for Analog Range OutputDigital Span Selection for Analog Range Output

Bargraph Center Point Display Mode Selection

STEP G

Bargraph Center Point Mode Selection (See example above)

1) To select bargraph center point mode, press the or

button. Display changes from [oFF] to [on].

2) Press the

button. Display toggles between [diSP] and [on]

or [oFF].

STEP H Digital Display ON/OFF Selection

1) To set the display to [oFF], press the or button. Display

toggles between [diSP] and [oFF].

2) Press the

button. The display exits the calibration mode

and returns to the operational display. Only the bargraph

display is on and the digital display is off.

If the digital display is selected to be off, pressing any button to

make programming changes or to view setpoints activates the digital display.

When the procedure is complete, the digital display will then automatically

switch off.

The Display/Bargraph settings are now complete.

Operational Display

STEP G

STEP H

See Example of Bargraph

Center Point Display Mode

Selection Above

From Digital Span Selection

for Analog Range Output Above

or Direct From Decimal Point

and Brightness Selection Page 5

if Analog Output Option is Not Present

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

STEP E

STEP F

This branch will only

appear if the analog

output option is installed

To Bargraph Center

Point Display Mode

Selection Below

From Decimal Point and

Brightness Selection

See Page 5

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comApr-23-2009 FL-B101D40 DS (FL7) Page 7

Clear Lockable NEMA 4X

Splash Proof Lens Cover

P/N.(OP-N4/144X36 )

133.5mm

(5.27")

Mosaic

Fitting

9/64 DIN

cutout

spacer

To open rear cover,

use a small flat

blade screw driver.

Press down lightly

to release catch and

leaver outwards.

SIDE VIEW

137.7mm

(5.42")

9/64 DIN

cutout

spacer 142.3mm

(5.62")

Max. panel thickness

43mm

(1.7")

For additional strength,

extra Mounting Slide Clips

can be ordered and doubled up

one behind the other.

P/N. (75-DMC144X36)

4.5mm

(0.18")

Metal Surround Case

P/N.(OP-MTL144X36) is pre-installed

at the factory and cannot be removed

without damage to the case.

Two bezel Trim

Strips are supplied with

each Panel Adaptor

Panel Adaptor to fit existing 6" Edgewise

Pointer Meter Cut-Outs P/N.(OP-PA/144x36)

Adaptor uses wide jaw mounting slide

clips.P/N.(75DMC14436B)

When extra panel

mounting tightness is

required,

order the optional

screw mount

clip.

P/N.(OPMTLCLIP)

FRONT VIEW

144mm

(5.69")

36mm

(1.42") 4mm

(0.16")

typical

9/64 DIN

36x144 mm

100

PANEL CUTOUT

138mm

(5.45")

33mm

(1.3")

Snug

Fitting

Loose

Fitting

8 places

7.5mm(0.3")

3.5mm(0.14")

4 places

32.2 mm

(1.27")

Mosaic

Fitting

133mm

(5.25")

135.2mm

(5.34")

3mm(0.12")

9/64 DIN

cutout

spacer

Case will mount in standard DIN cutouts

Various

bezel colors

are available.

Black is

standard.

The Metal Surround

case uses Metal

Screw Mount Clips

and has a max.

panel thickness

mounting of

7mm(0.28")

TOP VIEW

5mm

(0.20") 117.5mm

(4.64")

18.3mm (0.72")

Straight-thru

Connector

31mm

(1.22")

34mm

(1.34")

Mosaic Fitting

Right-angled

Connector

6mm

(0.24")

10mm

(0.39")

26.5mm (1.05")

Push-On Connector

for FI series IO board

The adapter snaps on

the 36x144 mm

(1.42"x5.69") case and

enables single unit or

stack mounting in an

existing 6" edgewise

pointer meter cut-out.

100

SP1 SP2 SP3 SP4

Zero Span Zero Span

Panel adaptor plates are

available to retrofit most

existing panel cutouts.

31mm

(1.22")

These dimensions are

increased by 2mm (0.08") when

the metal surround case is installed.

For extra strength in portable applications,

the 8 DIN spacers should be snipped

off and the Mosaic fitting cutout used.

Case Dimensions

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP E

Calibrate

Analog

Output

STEP F

Calibrate

Analog

Output

Will only appear if the analog

output option is installed

To Digital Span Selection

for Bargraph Display

See Page 5

To Two Point Digital

Calibration Mode

See Page 4

Operational Display

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

–x

4.00

–x

20.00

Determine if the Analog Output Selection Header is in the 4 to 20mA (0-20mA) position or the 0

to 10VDC position. If necessary, the module may have to be removed and the header position

changed (see Component Layout below).

Note: Always disconnect power from the meter before removing the analog output module to

adjust the mA or Volts output selection header and reinstalling it. When power is reconnected, the

meter’s software will automatically detect the presence or absence of the analog output module.

STEP A Enter the Calibration Mode

1) Press the

and buttons at the same time. Display toggles between [cAL] and [oFF].

2) Press the or button. Display changes from [oFF] to [on].

3) Press the

button. Display toggles between [cAL] and [out] input calibration.

Note: If at this point the display skips directly to toggle between Zero and the previous Zero

setting, the software is detecting that the optional analog output hardware is NOT installed.

STEP B

Enter the Two Point Analog [ouT] Output Range Setting and Calibration Mode

1) Press the

button. Display toggles between [cLo] and an internal scale factor.

STEP E Set or Calibrate [cLo] the Low Analog Value of the Analog Output Range

1) Connect a multimeter to analog output pins 17 and 18 (see Rear Panel Pinouts

on page 10). Using the and buttons, adjust the analog output to the desired

low value as measured on the multimeter. cLo may be adjusted to any value from

–0.3 mA to 18 mA (mA output selected) or from –0.6 V to 8 V (volt output selected).

However, the output of cLo must always be less than the value selected for chi. If

a reversed analog output is desired, the values selected to establish the Digital

Span can be reversed (see top of page 6). For digital readings outside the Digital

Span selected, the analog output will not go any lower than the calibrated value set

for cLo. However, the analog output will linearly rise above the value set for chi, up

to the the maximum analog output capability (see chi below).

2) Press the

button. Display toggles between [chi] and an internal scale factor.

STEP F Set or Calibrate [chi] the High Analog Value of the Analog Output Range

1) Using the and buttons, adjust the analog output to the desired high value

as measured on the multimeter display. chi may be adjusted to any value from 18

mA to 24 mA (mA output) or from 8 V to 10.3 V (volt output). However, the value

must be higher than the value selected for cLo. For digital readings outside the

Digital Span selected, the analog output will linearly rise above the value set for chi,

up to the maximum analog output capability.

2) Press the

button. The meter exits the calibration mode and returns to the

operational display.

Note: The analog output range established by the values selected for cLo and chi will occur, auto-

matically scaled, between the two digital values selected for AnHi and AnLo. However,

the analog

output can linearly rise above the chi value set for digital readings outside the digital span

selected. See Digital Span Selection on page 6.

Two Point Analog Output Range Setting and CalibrationTwo Point Analog Output Range Setting and Calibration

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 8 Apr-23-2009 FL-B101D40 DS (FL7)

Operational Display

SETPOINT SETTING

AND RELAY

CONFIGURATION MODE

STEP A

STEP B

STEP C

STEP D

No [doM] or [dob]

STEP E

STEP F

STEP G

STEP H

STEP I

STEP J

STEP K

STEP L

To Step M of Setpoint

Setting and Relay

Configuration Page 9

The following programming steps are required to enter the setpoint values and configure the relay functions

in a meter with four relays using four setpoints. Generally if less than four relays are installed, the setpoints

without relays are operational in software for tri-color control or display only purposes. To remove unwanted

setpoint indications, set them to 9999 or -1999 depending on the relay activation mode selected.

STEP A Enter the Setpoint Mode

1) Press the

and buttons at the same time. Display toggles between [SP1] and the previous

SP1 setting.

STEP B Set Setpoint 1 [SP1]

1) Using the and buttons, adjust the display to the desired SP1 value.

2) Press the

button. Display toggles between [doM] and the previous [doM] setting.

STEP C Set the SP1 Delay-on-Make [doM] Delay Time Setting

Using the and buttons, adjust the display to the desired [doM] value (0 to 9999 seconds).

The reading must continuously remain in an alarm condition until this delay time has elapsed before

the relay will make contact (energize).

2) Press the

button. Display toggles between [dob] and the previous [dob] setting.

STEP D Set the SP1 Delay-on-Break [dob] Delay Time Setting

Using the and buttons, adjust the display to the desired [dob] value (0 to 9999 seconds).

The reading must continuously remain in a non-alarm condition until this delay time has elapsed

before the relay will break contact (de-energize).

2) Press the

button. Display toggles between [hYSt] and the previous [hYSt] setting.

STEP E Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between PUM and (on) or (oFF).

STEP F Select Pump [PUM] (on) or (oFF)

Using the and buttons, select the Pump to be ON or OFF. When PUM is selected ON, and

SP2 is set at a value higher than SP1, the SP1 relay will operate in a special "pump on pump off" mode.

SP2 acts as the upper limit and SP1 acts as the lower limit of the Hysteresis Band on the SP1 relay.

For filling applications:

[rLYS] should be set to [LhXX] (see step M). The SP1 relay and SP1 LED Annunciator will then activate for inputs

less than the SP1 setpoint, and remain ON until the SP2 setpoint is reached.

For emptying applications:

[rLYS] should be set to [hhXX] (see step M). The SP1 relay and SP1 LED Annunciator will then activate for inputs

greater than the SP2 setpoint, and remain ON until the SP1 setpoint is reached.

2) Press the

button. Display toggles between [SP2] and the previous SP2 setting.

STEP G Set Setpoint 2 (SP2)

1) Using the and buttons, adjust the display to the desired SP2 value.

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP H Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between [SP3] and the previous [SP3] setting.

STEP I Set Setpoint 3 (SP3) (No [doM] or [dob])

1) Using the and buttons, adjust the display to the desired SP3 value.

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP J Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between [SP4] and the previous [SP4] setting.

STEP K Set Setpoint 4 (SP4) (No [doM] or [dob])

Using the and buttons, adjust the display to the desired SP4 value.

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP L Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between [rLYS] and the previous relay setting.

Please Continue On Next Page.

Setpoint Setting and Relay Configuration Mode

Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comApr-23-2009 FL-B101D40 DS (FL7) Page 9

STEP M

STEP N

STEP O

STEP P

STEP Q

STEP R

STEP S

STEP T

STEP U

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

Operational Display

From From Step L of

Setpoint Setting and Relay

Configuration Page 8

L or h

To comply with the latest safety requirements, the tri-color bargraph is designed like a traffic light, to

display either red, orange or green, but only one color at a time. When the bar reaches a selected

color change point, the entire bar will change to the color designated for that zone. This eliminates any

ambiguity as to the signal status, especially just after transitioning to a new zone.

First (Step Q) is to select the color to be displayed, when the bar is “below*”, whichever set point is set

to the lowest position.

Second (Steps R, S, T, and U) is to select the color to be displayed when the bar is above each specific

set point, regardless of the order or position to which the set points are set.

However, if two or more setpoints with differently specified colors are positioned at the same set point

value, the color specified for the set point with the highest identifying number will be displayed. When set

points are set to the same value, the SP4 color overrides the SP3 color, the SP3 color overrides the SP2

color, and the SP2 color overrides the SP1 color.

STEP Q Select Bargraph Color when the bar is BELOW* the Setpoint that is set to the lowest

position