The Handy B.U.L. Parts list manual

!
B.U.L. INSTRUCTIONS AND PARTS BREAK DOWN
Limited Lifetime Warranty
Handy, Division of Janco Industries, Inc. is providing a limited lifetime warranty on The B.U.L. lift. The purchaser must provide Handy
with a legible copy of the purchase receipt to obtain this warranty. The purchaser must provide Handy notice of the defect and establish
that the equipment was properly set up, maintained and operated within the limits of rated and normal usage. Handy, Division of Janco
Industries, Inc. reserves the right to have its product shipped back to the factory for inspection to ensure the lift was not being used above
its rated limits and capacity. The purchaser is responsible for freight charges until a determination is made by Handy. Handy will
reimburse the purchaser if it is determined that he or she was not using lift above the rated capacity. This warranty covers the structure of
the lift itself. It does not cover any cost of labor, transportation, freight, installation, misuse, abuse, or failure of the foot pedal due to rust
and or moisture. Also excluded in this warranty are items that were purchased for the Handy lift and installed on it at the factory such as
air bellows, wheels, and bearings. Parts considered wearable carry a 90-day warranty. All other parts excluded from the lifetime warranty
carry a 1-year warranty from time of purchase. If the lift is purchased from an un-authorized distributor, eBay or other online service, you
are not eligible to receive the limited lifetime warranty for the structure of the lift. This warranty is only offered to the original purchaser
and is non-transferrable. It must be purchased from Handy, Division of Janco Industries, Inc. or one of its authorized distributors.

!
!
UNPACKING AND SET-UP -(FIGURE 1)
1-!Cut banding, and remove carton top.
2-!Remove 2 anchors, that secure lift to the pallet.
3-!Remove air hose, and connect to air supply.
4-!Stand clear of lift table, and depress the UP side of the foot pedal to raise lift.
5-!Lower detent bars and release air pressure by depressing the DOWN side of the foot pedal.
6-!Remove support bars from under the lift and install on top of the lift.
7-!(Utilizing 2 people) slide one end of the lift off the pallet, while the second person stabilizes the other
side.
8-!Slide other end off of the pallet and discard pallet.
FIGURE 1

!
!
www.handyindustries.com!
OPERATION
1.!Loads must be centered at all times. Lift is rated at a maximum of 2500 lbs.
2.!It is the operator’s responsibility to determine if load needs to be additionally secured with straps.
3.!To raise lift depress UP side of the pedal, to lower lift depress DOWN side of the pedal.
4.!Support arms should be adjusted to support vehicle at appropriate lifting points.
5.!Once lift is raised to the desired height, flip down BOTH detent bars, and release air pressure so that the
lift comes to rest on the detent bars. ALWAYS make sure to you use BOTH detent bars, and check
visually to make sure they come to rest in the same detent teeth.
!FAILURE TO CORRECTLY USE BOTH DETENT BARS COULD CAUSE SERIOUS INJURY
AND/OR PROPERTY DAMAGE!
!IT IS VERY IMPORTANT THAT OIL DRAIN PAN IS RETURNED TO EITHER END OF
THE LIFT TO PREVENT DAMAGE WHEN LOWERING LIFT.
RECOMMENDED MAINTENANCE - FIGURE 2
Daily visual checks: Check that all pins are secured with appropriate retaining rings. Inspect air bag, and air
hose for leaks, wear, and interference with lift frames.
1.!All moving parts have been lubricated at the factory, and should be re-lubricated every month to prevent
galling. Grease points noted on Fig. 2
2.!Grease also may need to be applied to the support arm pins located on the lift top, to prevent galling.
!NOTE:!READ!ENTIRE!MANUAL!TO!COMPLY!WITH!ALL!SAFETY!AND!SERVICE!PRECAUTIONS.!!SERIOUS!
INJURY!AND/OR!PROPERTY!DAMAGE!MAY!OCCUR!UNLESS!INSTRUCTIONS!ARE!FOLLOWED!CAREFULLY.!
!
!
Figure 2

!
!
www.handyindustries.com!