The Handy 16007G User manual

1. Center load on table
-
1
0
00 lb. maximum.
2. Connect to 115v power supply.
3. Keep hands and tools from under carriage.
4. Do not mount table when in elevated position.
5. Do not ride vehicle onto lift.
6. Lift must be in the lowered position when moving.
7. Only trained persons should operate Lift.
8. The working area should be sufficiently lit.
9. Recommended for indoor use only.
10. Tie-down straps must be used in conjunction with
the holes provided in the lift top.
S.A.M. ELECTRIC LIFT
WITH PUSH BUTTON CONTROL
λ
INSTRUCTIONS
λ
PARTS DRAWING
λ
PART LIST
P/N 16007G
-
16007O
-
16007R
-
16007B

POWER SUPPLY
This lift is for operation on 115 volt, 60 Hz current only. Check outlet voltage before plugging in equipment.
 WARNING: This lift is equipped with a 3-prong plug which must be plugged into a grounded
115 volt, 60 Hz power supply for your safety. Removing ground prong from plug or failure to
plug into a grounded receptacle may result in a fatal electric shock.
UNPACKING AND SET-UP
1. Open carton, then remove ramp and shipping boards.
2. Keeping hands free of lift mechanisms to avoid personal injury-CAREFULLY turn left over.
3. Mount ramp to lift top by inserting ramp tabs into slots on lift top.
NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.
OPERATION- LUBRICATION
1. Loads must be centered on table at all times.
2. Loads must be firmly positioned and secured on table at all times. Tie-down straps must be used
in conjunction with the holes provided in the lift top.
3. All moving parts have been lubricated at the factory and should be re-lubricated every 6
months to prevent galling. Grease zerks are located at each end of frame pivot shaft and at
top ends of inside frame assembly.
4. The drive screw, motor and gear box were factory lubricated, and this lubrication should last for the life
of the lift. Should re-lubrication be necessary, use a No. 9 multi-purpose gear oil in gear box and an “O”
grade gear grease on drive screw.
5. Frame/motor pivot shaft set screws should be checked frequently to be sure they are tight. These are
located at the top of the inside frame.
INSTALLING: The drive train components have been burnished in to give a tight, well working fit and will be
stiff for the first few cycles. If drive screw should seize, put a few drops of oil on screw and reverse a few times.
If motor should pull down or hum, TURN OFF IMMEDIATELY. Check to see if drive screw is free.
OTHER OPTIONS AVAILABLE Separate installation instructions included with each option.
PART # DESCRIPTION
14476 CV-17 CYCLE VISE – Vise with rem ovable wheel stop b uilt into vise
10728 12” SIDE EXTENSIONS ( 2) – Expa nd s wid th of lift from 24” to 48” includ es sta bilizer
b a r
16011 13” FRONT EXTENSION – Extend s lift top to 93” for long er wheel b a se m otorc yc les
10736 13” REAR EXTENSION – Extend s lift top to 93” for long er wheel b a se m o torc yc les
15566 RAMP END EXTENSIONS – Atta c hes to end of lift ra m p for a m ore g ra d ua l inc line to
p revent b ig g er b ikes from d ra g g ing b ottom .
10737 SNOWMOBILE WING KIT – Used when lifting snowm o b iles
16355 CE FOOT PEDAL – Covered foot p ed a l
10732 LIFT DOLLY – Help s m ove lift while in d own p osition
16010 TOOL TRAY – Keep s tools orga nized a nd Ha nd y
NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS.
DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS
ARE FOLLOWED CAREFULLY.

PARTS DRAWING - PARTS LIST

WIRING DIAGRAM

ELECTRIC CONTROL SYSTEM

Ph: 855-752-5446 Fax: [phone]
www.handyindustries.com
16487 7-11-14
Limited Lifetime Warranty
Handy, Division of Janco Industries, Inc. is providing a limited lifetime warranty on its motorcycle lift line. This Lifetime Limited
Warranty is available on lifts that have a serial number the same as or greater than those listed. Standard 1000 air and electric #ST 0138,
SAM 1000 air and electric #S 0082, SAM2 1000 air #S2 0020, BOB 1500 air #B 0100, Electric/Hydraulic 1500 #H 0008, Gruntavore 1800
#GR 0004, B.U.L. (all serial numbers), Dual Lift (all serial numbers). The purchaser must provide Handy with a legible copy of the
purchase receipt to obtain this warranty. The purchaser must provide Handy notice of the defect and establish that the equipment was
properly set up, maintained and operated within the limits of rated and normal usage. Handy, Division of Janco Industries, Inc. reserves the
right to have its product shipped back to the factory for inspection to ensure the lift was not being used above its rated limits and capacity.
The purchaser is responsible for freight charges until a determination is made by Handy. Handy will reimburse the purchaser if it is
determined that he or she was not using lift above the rated capacity. This warranty covers the structure of the following models of Handy
lifts: Standard 1000, SAM 1000, SAM2 1000, BOB 1500, Electric/Hydraulic 1500, Gruntavore 1800, B.U.L., Dual Lift. Attachments for
these lift models are not included in the limited lifetime warranty. This warranty only covers the structure of the lift itself. It does not cover
any cost of labor, transportation, freight, installation, misuse, abuse, or rust or failure of the air cylinder and/or foot pedal due to rust and or
moisture. Also excluded in this warranty are items that were purchased for the Handy lift and installed on it at the factory such as electric
motors, hand-held pendants and bearings. Parts considered wearable carry a 90-day warranty. All other parts excluded from the lifetime
warranty carry a 1-year warranty from time of purchase. If the lift is purchased from a un-authorized distributor, eBay or other online
service, you are not eligible to receive the limited lifetime warranty for the structure of the lift. This warranty is only offered to the original
purchaser and is non-transferable. It must be purchased from Handy, Division of Janco Industries, Inc. or one of its authorized distributors.