AMGO Hydraulics OHX-10 Manual

TWO POST LIFT
Model: OHX-10/OHX-10H
Original

CONTENTS
Product Features and Specifications ..............................................1
Installation Requirement .............................................................5
Steps of Installation ...................................................................6
Exploded View ..........................................................................32
Test Run ...................................................................................41
Operation Instruction .................................................................43
Maintenance .............................................................................44
Trouble Shooting .......................................................................45
Lift disposal ..............................................................................45

1
I. PRODUCT FEATURES AND SPECIFICATIONS
CLEAR-FLOOR DIRECT-DRIVED MODEL FEATURES
Model OHX-10 (See Fig. 1)
· Direct-drived design, minimize the lift wear parts and breakdown ratio
· Dual hydraulic cylinders, designed and made as USA standards, utilizing oil seal in
cylinder
· Self- lubricating UHMW Polyethylene sliders and bronze bush
· Single-point safety release, and dual safety design
. Clear-floor design, provide unobstructed floor space
. Overhead safety shut-off device prevents vehicle damages
· Stackable rubber pads
SPECIFICATIONS
Model
Lifting
Capacity
Lifting
Time
Lifting Height
Overall
Height
Overall
Width
Minimum
Pad Height
Motor
OHX-10
10000lbs
57S
71-1/2”～80-1/2”
144”
135”
3-1/2”～12-1/2”
2.0HP
Fig. 1

2
Model OHX-10H (See Fig. 2)
· Direct-drived design, minimize the lift wear parts and breakdown ratio
· Dual hydraulic cylinders, designed and made as USA standards, utilizing oil seal in
cylinder
· Self- lubricating UHMW Polyethylene sliders and bronze bush
· Single-point safety release, and dual safety design
. Clear-floor design, provide unobstructed floor space
. Overhead safety shut-off device prevents vehicle damage
· Stackable rubber pads
· Adjustable column height
SPECIFICATIONS
Model
Lifting
Capacity
Lifting
Time
Lifting Height
Overall
Height
Overall
Width
Minimum
Pad Height
Motor
OHX-10H
10000lbs
63s
78-1/2”~87-1/2”
157”/168”
135”
3-1/2”～12-1/2”
2.0HP
Fig. 2

3
Arm Swings View
Car in
Fig. 3

4
Swing and extending the arms to the lifting point of vehicle
Fig. 4

5
II. INSTALLATION REQUIREMENT
A. TOOLS REQUIRED
Rotary Hammer Drill (Φ3/4)
Hammer
Level Bar
English Spanner (12")
Ratchet Spanner with Socket (28#)

Wrench set
(10＃、13＃、14＃、15＃、17＃、19#、24＃、27＃)
Carpenter’s Chalk
Screw Sets
Tape Measure (7.5m)
Pliers
Socket Head Wrench (6#)
Lock Wrench
Fig. 5

6
B. SPECIFICATIONS OF CONCRETE (See Fig. 6)
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 6” minimum and without reinforcing steel bars, and
must be dried completely before the installation.
2. Concrete must be in good condition and must be of test strength 3,000psi
minimum.
3. Floors must be level without cracks.
C. POWER SUPPLY
The electrical source must be 2.0HP minimum. The source cable size must be 2.5mm²
and in good condition of contacting with floor.
III.STEPS OF INSTALLATION
A. Location of Installation
Check and insure the installation location (concrete, layout, space size etc.) is
suitable for lift installation.
B. Use a carpenter’s chalk line to establish installation layout of base-plate (See Fig.7).
Fig. 7
Fig. 6
Click a line
59
6”
Concrete must be 3,000psi
minimum

7
C. Check the parts before assembly.
1. Packaged lift and hydraulic power unit (See Fig. 8).
2. Move aside the lift with fork lift or hoist, and open the extension packing carefully, take
off the lifting arms and parts box from upper and inside the column, then move them
to location nearby installation site, check the parts according to the shipment parts
list (See Fig.9).
3. Loose the screws of the upper package stand, take off the upper extension columns,
take out the parts in the inner column and remove the package stand
4. Move aside the parts and check the parts according to the shipment parts list
(See Fig.10, 11, 12).
Shipment Parts list
Parts box
Lifting Arm
Parts box
Fig. 8
Fig. 9
Fig. 10
Outer Column （only
OHX-10H）
88
87

8
5. Open the bag 1 of parts and check the parts according to parts box list (See Fig. 13,14).
Fig. 13
Part box①（87）
Fig. 11
Part box②(88)
Fig. 12
OHX-10
Accessories

9
Car in
Power-side column
Offside column
6. Open the bag 2 of parts and check the parts according to parts bag list (See Fig. 15).
D. Place the two columns in parallel on the ground of installation position, and
determine the installation position of the power side column according to the
condition of the installation site. Under normal circumstances, the power side
column is installed on the right side of the entering direction; then install the oil
hose.
OHX-10H
Accessories
Fig. 14
Fig. 15
Fig.16
Oil hose passes through
the retainer on column

10
E. Install the cylinder and connect the oil hose to the cylinder.
F. Mounting column assemble.
1. OHX-10 mounting column assemble. Fig.18 & 19.
B
A
Fig.17
Install cylinder
fitting and oil hose
After connection
C
C Magnified view
A View
Offside column
Fig. 18
B View
power-side column
Fig. 19
66
32
65
23
24
25
26

11
2. OHX-10H Mounting column assemble. Fig. 20.
Fig.20
A
A Magnified view
23
24
25
26
28
66
32
65
Offside column
Power-side column

12
Place the two columns in parallel on the ground of the installation position, and
determine the installation position of the power-side column according to the
condition of the installation site. Under normal circumstances, the power-side
column is installed on the right side of the entering direction; when installing
the outer column, it should be installed according to the height of the workshop.
When the height is not more than 168", the mounting column is selected to
install the lower position; when the height is more than 168", the mounting
column can be installed with the high position. (See Fig.21)
Fig.21
Mounting column low
setting
Mounting column high setting
28
2
3
1
18

13
G. Vertical leveling of columns (See Fig. 22)
1. OHX-10
Put the columns on the installation layout of base-plate, install the anchor bolts. Check
the Columns plumpness with level bar, and adjusting with the shims if the columns are
not vertical. Do not tighten the Anchor Bolts.
Drilling
Cleaning
Bolting
3-1/2”
Fig.22
77
76
Width：135”
Width：112-1/4”
*Note: The anchor bolt is knocked into the
ground at least 3-1/2".

14
2. OHX-10H
Put the columns on the installation layout of base-plate, install the anchor bolts. Check
the Columns plumpness with level bar, and adjusting with the shims if the columns are
not vertical. Do not tighten the Anchor Bolts. (See Fig. 23)
*Note: The anchor bolt is knocked into the ground at least 3-1/2".
3-1/2”
Fig.23
Width:135”
77
76
Width：112-1/4”

15
H. Install overhead top beam (See Fig. 24).
Fig.24
Install the top beam
with equipment
50
51
68
32
68
32
Top beam connecting groove assemble
holes
Only OHX-10H

16
I. Installing the limit switch control bar and limit switch (See Fig. 25).
Limit switch
connected
with cable
Fig. 25
Limit switch cable wiring
Connect the brown wire
to the terminal 12# on
limit switch and terminal
4# on control button.
Connect the blue wire
to terminal 11# on
limit switch and
terminal A1 on AC
contactor of power unit
Adjust drive rod of limit
switch
Connect the yellow and
green wire to the earth
wire terminal on limit
switch and the earth wire
terminal of power unit.
68
34
33
29
34
35
Loosen screw of drive
rod for adjustment

17
I. Lift the carriages up and make them be locked at the same level (See Fig. 26).
Fig.26

18
K. Install cables
1. OHX-10 cable connection.
Cables pass through the bottom of the carriages and be pulled out from the
square hole of carriages, then screw the two cable nuts (See Fig. 27)
Fig.27
78
79
Nuts
lock
each
other