The Land of Nod Hampshire Spindle Crib User manual

- Failure to follow these warnings and assembly instructions could result in serious injury or death.
- Read all instructions before assembling crib. Keep instructions for future use.
-Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
-To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
- Strings can cause strangulation! DO NOT place items with a string, cord or ribbon around a child’s neck,
such as hood strings or pacifier cords. DO NOT suspend strings over crib or toddler bed, or attach strings to
toys for any reason.
-To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose
fasteners.
- DO NOT place crib or toddler bed near windows where cords from blinds or drapes may strangle a child.
Fall Hazard:
- When child is able to pull to standing position, set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps for climbing out.
-When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be used
and the child should be placed in a youth or regular bed.
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27-1/4 INCHES (69 cm) BY 51-5/8
INCHES (131 cm) WITH A THICKNESS NOT EXCEEDING
6 INCHES (15 cm).
- Check this product for damaged hardware, loose joints, missing pats or sharp edges before and after
assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any
parts are missing, damaged, or broken. Contact The Land of Nod® for replacement parts and instructional
literature if needed. DO NOT substitute parts.
- If refinishing, use a non-toxic finish specified for children’s products.
- Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
- Infants can suffocate in gaps between crib sides and a mattress that is too small.
- Periodically check to see that all bolts are securely tightened.
- To clean crib: Wipe with clean soft cloth dampened with a mild cleanser and water. Rinse with clean water
using a soft cloth, and dry thoroughly.
- Follow warnings on all products in a crib.
- When a vaporizer is in use, always aim vapor steam away from the crib as well as away from other wood
furniture.
WARNING:
!
!
WARNING:
!
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Hampshire Spindle Crib Assembly Instructions
Made in Vietnam - r05

The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Hampshire Spindle Crib Assembly Instructions
Page 1 of 4
Made in Vietnam - r05
This page lists the contents included in the box. Please take
time to identify the hardware as well as the individual
components of the product. As you unpack and prepare for
assembly, place the contents on a carpeted or padded area
to protect them from damage. Please follow the assembly
instructions closely. Improper assembly can result in
personal or property damage.
Note: 2 adults are required to safely assemble this product.
WARNING:
CHOKING HAZARD - SMALL PARTS
Small parts present in unassembled state.
Adult assembly required.
1 - Large Allen
wrench
1 - Small Allen
wrench
2 - End panels2 - Side panels
1 - Mattress panel
4 - Bolt caps
8 - Small bolts
4 - Brackets
4 - Spring
washers
4 - Half-moon
brackets
4 - Large bolts
4 - Support
pin

1
2
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Hampshire Spindle Crib Assembly Instructions
Page 2 of 4
Made in Vietnam - r05
Attach 2 brackets to end panel with 1 small bolt per bracket as shown. Secure, but do not over tighten, bolt with small
Allen wrench. Repeat steps for remaining end panel.
With the assistance of another adult, fit pre-assembled wood dowels of side panels into corresponding holes of end
panels. Make sure bracket of each end panel are positioned securely into corresponding slots of each side panel.

Determine the desired height (low, middle, high) for the crib mattress. Fit each support pin into corresponding corner
as shown. Make sure support pin is securely engaged with assembly.
3
4
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Hampshire Spindle Crib Assembly Instructions
Page 3 of 4
Made in Vietnam - r05
Using a small Allen wrench, loosely attach top assembly with 1 small bolt through each bracket as shown. Using a large
Allen wrench, loosely attach bottom assembly with 1 large bolt, 1 spring washer and 1 half-moon bracket per corner as
shown. Do not fully tighten bolts until further instructions.
high
middle
low

5
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Hampshire Spindle Crib Assembly Instructions
Page 4 of 4
Made in Vietnam - r05
CLEANINGANDCARE:
Cleansurfaceswithadryordampsoftcloth.Donotuseabrasivecleaners. Periodically check and tighten hardware as necessary.
Once the crib is in use, periodically check to make sure all bolts are tight, and tighten as necessary. Keep these
instructions for future use.
MAINTENANCE
Upon completion of assembly, be sure all screws, bolts and fastening devices have been tightened securely.
Periodically repeat this check to make sure all screws, bolts and fastening devices are tight. Before each usage or
assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts
are missing or broken. DO NOT substitute parts. DO NOT make any alteration to this crib.
CLEANING
Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean cloth
lightly dampened in the solution. Rinse with clean water again using a soft clean cloth, then dry all surfaces
thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COARSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE
After completing the assembly process you are advised to read and beware of all WARNINGS, CAUTIONS,
CLEANING, STORAGE, USE AND MAINTENANCE notices contained in these instructions. For long term storage of
the crib, store in a cool, dry place and keep away from moisture and extreme temperature changes.
NOTE: Make sure
metal plate of mattress
panel is at the bottom
during assembly
With the assistance of another adult, fit mattress panel onto corresponding support pins of crib assembly. From the top of
mattress panel, secure bolt caps onto each support pin with a small Allen wrench. At this point, fully secure all bolts.
Assembly is now complete.