The Land of Nod FLAT TOP 60 inch Bookcase User manual

TOOLS REQUIRED
WARNING: Adult Assembly Required
!
Made in Vietnam - r03 Page 1 of 4
Thank you for purchasing the Flat Top 60”Bookcase.
This page lists all the contents included in the box.
Please take the time to identify the hardware as well as
the individual components to this product. As you
unpack and prepare for assembly, place the contents on
a carpeted or padded area to protect them from
damage.
Note: 2 people are required to safely assemble this product.
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
15 - spring
washers
ASSEMBLY HARDWARE
15 - bolts
2 - side panels
(1 left, 1 right)
1 - front panel
phillips head screwdriver
Missing hardware? Please call 800.933.9904 for replacements.
NOTE: Contains small parts. Keep away from small children.
(We recommend the use of hand tools instead of power tools)
FLAT TOP
60” BOOKCASE
COMPONENTS
15 - flat
washers
22 - large
screws
18 - wood
dowels
8 - small
screws
8 - support
pins
1 - bottom
panel
1 - top panel
2 - adjustable
shelves
1 - fixed
shelf
1 - center
back panel
2 - back panels
(1 left, 1 right)

1
A. Insert 8 wood dowels into right side panels
as shown.
B. Fit dowels of right side panel into top panel
and fixed shelf with 2 bolts, 2 spring washers
and 2 flat washers. Secure, but do not over
tighten bolts with a phillps head screwdriver. 2
3 4
A. Insert 8 wood dowels into left side panel.
B. Fit dowels of left side panel into assembly
and secure assembly with 7 bolts, 7 spring
washers and 7 flat washers as shown.
C. Secure bottom and front panel with 1 bolt, 1
spring washer and 1 flat washer as shown.
Made in Vietnam - r03 Page 2 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
right side
panel
FLAT TOP
60” BOOKCASE
A. Insert 2 wood dowels into bottom panel and fit
into front panel as shown.
B. Fit bottom and front panels into dowels of right
side panel.
C. Secure bottom panel to right side panel with 2
bolts, 2 spring washers and 2 flat washers as
shown. Secure front panel to right side panel with 1
bolt, 1 spring washer and 1 flat washer as shown.
NOTE: Make sure front
apron of each panel are
positioned as shown
A. With the assistance of another adult, position
unit upright. Attach left back panel to assembly
with 8 screws, using a screwdriver. Do not over
tighten.
B. Attach center back panel with 6 screws.
C. Attach right back panel to assembly with 8
screws, using a screwdriver.
A
B
A
B
fixed
shelf
top
panel
NOTE: Do not over
tighten the bolts
right side
panel
front
panel
bottom
panel
A
C
C
B
A
A
B
C
C
left side
panel A
left
back
panel
center
back
panel right
back
panel
AC
B
B
A
NOTE: Do not over
tighten the screws

5
A. Insert 8 support pins into side panels at
desired shelf heights.
B. Place 2 adjustable shelves onto support
pins and secure shelves to each pin with 1
small screw as shown.
Assembly is now complete.
Made in Vietnam - r03 Page 3 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners. Do not use
furniture wax or polish as the unit is finished
with a protective clear lacquer.
adjustable
shelf
FLAT TOP
60” BOOKCASE
A
B
A

For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 2 mounting brackets to back of unit using 2 small screws per bracket as shown.
B) Determine the final location of unit. Mark position on the wall, approximately 2" below each wall bracket mounted
to the back of the unit.
C) Drill holes into marked positions on the wall and into a wall stud. If the wall stud is not available, drill a hole in the wall
that is slightly smaller in diameter than the anchor. Gently tap 4 plastic anchors until the flange of each anchor is
flush with the wall.
D) Attach 2 mounting brackets to the wall by inserting 2 large screws per bracket. Using a screwdriver, make sure
each screw is secured through the mounting bracket and into the plastic anchor in the wall.
E) With assistance of another adult, position the unit so the mounting brackets on the back edge are aligned with the
mounting brackets on the wall.
F) Attach 2 wall straps to corresponding mounting brackets as shown. Lace one end of the wall strap through both
brackets and into the other end of the strap. Pull tightly on the wall strap to secure.
Wall mounting assembly is now complete.
Serious or fatal crushing injuries can occur from furniture
tip over. Use of tip-over restraints may only reduce, but
not eliminate, the risk of tip-over. To help prevent tip-over,
install tip restraint per instructions below.
WARNING
!
MOUNTING HARDWARE
TOOLS REQUIRED
WALL MOUNTING ASSEMBLY
power drill
(for pilot holes only)
phillips head screwdriver
FLAT TOP
60” BOOKCASE
Made in Vietnam - r03 Page 4 of 4
Customer Service 800.933.9904 | Latest instructions available at www.landofnod.com
A
C
D
small
screw
mounting
bracket
plastic
anchor
large
screw
wall
strap
mounting
bracket
4 - small
screws
4 - large
screws
4 - plastic
anchors
4 - mounting
brackets
Missing hardware? Please call 800.933.9904
for replacements. NOTE: Contains small
parts. Keep away from small children.
2 - wall straps