THE RADIATOR COMPANY Ellipsis User manual

1
2
”
The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company
notied within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be tted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been tted. This
includes any consequential loss or cost of tting.
If The Radiator Company are not notied within 28 days of the date on the signed delivery note then
it will be deemed that The Radiator Company have fully complied with its obligations and claims will
not be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging to
prevent damage prior to installation. The Radiator Company cannot accept responsibility for items
damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make
over to you the benet of any warranty or guarantee given by the manufacturer, which is usually ve
years on most of our range. (Copies of specic guarantees for any of our products are available on
request).
The guarantees in all cases are subject to the products being installed in accordance with British and
or European standards as well as these tting instructions. The guarantees in all cases are restricted
to the free of charge replacement or repair of the failed product only. Our liability will under no
circumstances extend beyond the repair or replacement of the product supplied by us. Claims
for either labour in replacement or damage to property are not admissible. Any goods that are
returned, in the event of a problem, will belong to The Radiator Company.
Technical Specications
The elegant oval tubes 25mm x 50mm create
strong lines and a pleasing aesthetic.
Please read these instructions and terms and
conditons carefully prior to installation.
Failure to do so may invalidate the warranty
Ellipsis
Horizontal
Fittings Instructions
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
Materials Steel
Connections ow and return.
Test pressure 6.5 Bar
Testing authority EN442
Maximum operating pressure 5 Bar
Maximum working temperature 95 ºC
Packaging Polythene lm protection within cardboard box
THE
RADIATOR
COMPANY
ELLIH1.2
PLEASE NOTE: Systems using micro bore pipework must have adequate pressure and
ow rates for the number and style of radiators on the system.

Unpack & Inspect
1
You should have:
• 1 Radiator
• 4 Wall brackets (only Single model)
• 4 Wall bracket Studs (only Double model)
• 4 Wall bracket Sleeves (only Double model)
You will need:
• Tape measure
• Electric drill and bits
• Spirit level
Contents
2
Mark and Fix Brackets continued
Diagrams of Ellipsis Horizontal
The Radiator Company prides itself on selecting products from
manufacturers who exercise tight quality control measures. We
only select models with excellent standards of welding and
brazing, as well as high quality nishes. All of our products are well
packaged and should reach you in perfect condition. Just in case
however, we offer a minimum 5-year no quibble
guarantee for all radiators and towel rails.
The Radiator Company must be notied of any
shortages or damage within 28 days of delivery.
For further information please see terms and
conditions on back page.
PLEASE NOTE :
It is essential that all brackets are level to
ensure a vertical alignment for connecting the
pipework.
Pipe Centres
Pipe centres left to right
Pipe centres from wall
Depth from wall
Commission
4
Please Note:
In accordance with Part L1 2006 of the Building Regulations and
BS7593:1992 code of practice for the treatment of hot water
and central heating systems, we strongly recommend flushing
the heating system post installation of new radiators and then
adding the correct quantity and type of inhibitor for use with
your radiator and system to prevent corrosion. Damage caused to
systems not protected by a suitable inhibitor will not be covered
by manufacturer’s guarantee.
50
25 Ø30
50
25 Ø30
80
width - 34mm
Double
Single
85 - 88
60
60
127
60
60
10
10
Mark and Fix Brackets
3
Ellipsis Single
1. Screw on the bracket studs to the radiator.
2. With the bracket studs securely xed, you may either hold up the
radiator to the wall and mark out the bracket sleeve positions, or use
the dimensions on the appropiate drawings opposite.
3. Using a suitable drill bit and plugs, secure the top two bracket
sleeves to wall and hang the radiator to ensure it is level. With the
positions correct, mark out the bottom bracket positions.
4. Using a suitable drill bit and plugs, secure the bottom bracket
sleeves to wall and hang the radiator to ensure it is level.
5. When all sleeves are xed and level, slot in the radiator, and
tighten the grub screws on the side of the brackets so secure.
Ellipsis Double
There are no xed bracket positions for the Tallis
Double, however for even weight distribution
we suggest placing the brackets close to the
collectors and between the top and bottom two
elements (please refer to diagram opposite)
1. Using the bracket diagram as a guide, position
the bracket heads between the elements and
secure with the supplied screw.
2. Offer up the radiator to the wall and mark the
position on the wall for the bracket sleeves, and
x to the wall using suitable drill bits and plugs.
3. Offer up the radiator to the wall and slot into the bracket sleeves,
and mark the positions for the bottom two brackets sleeves. Take
down the radiator, and using suitable drill bits and plugs, hang the
bottom two bracket sleeves.
4. With all 4 brackets tted, tighten the grub screws on the side to
secure.
width - 34mm
45mm - 48mm
85mm - 88mm
width - 34mm
87mm
127mm
Single Double
45 - 48
87