THE RADIATOR COMPANY BDO 25 User manual

Materials Steel
Connections ow and return.
Test pressure 13 Bar
Testing authority EN442
Maximum operating pressure 10 Bar
Maximum working temperature 90 ºC
Packaging Foam wrapping in Cardboard Box
1
2
”
The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company
notied within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be tted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been tted. This
includes any consequential loss or cost of tting.
If The Radiator Company are not notied within 28 days of the date on the signed delivery note then
it will be deemed that The Radiator Company have fully complied with its obligations and claims will
not be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging to
prevent damage prior to installation. The Radiator Company cannot accept responsibility for items
damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make
over to you the benet of any warranty or guarantee given by the manufacturer, which is usually ve
years on most of our range. (Copies of specic guarantees for any of our products are available on
request).
The guarantees in all cases are subject to the products being installed in accordance with British and
or European standards as well as these tting instructions. The guarantees in all cases are restricted
to the free of charge replacement or repair of the failed product only. Our liability will under no
circumstances extend beyond the repair or replacement of the product supplied by us. Claims
for either labour in replacement or damage to property are not admissible. Any goods that are
returned, in the event of a problem, will belong to The Radiator Company.
Technical Specications
Lots of hanging space and strong outputs,
the BDO 25 is a welcome addition to the TRC
25 Range.
Please read these instructions and terms and
conditions carefully prior to installation.
Failure to do so may invalidate the warranty
BDO 25
Fittings Instructions
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
THE
RADIATOR
COMPANY
BDO251.3
PLEASE NOTE: Systems using micro bore pipework must have adequate pressure and ow rates
for the number and style of radiators on the system.

Diagrams of BDO 25
102 - 116
63 - 77
72
72
17.5
Bracket Sleeve
Bracket Stud
Bracket Assembly
Unpack & Inspect
You should have:
• 1 Radiator
• 4 Wall brackets sleeves
• 4 Wall brackets studs
• 1 Blanking Plug
• Air vent
Using a suitable drill bit, screws and plugs, loosely x the top two
brackets sleeves onto the wall where marked using the dimensions in
section 3, (refer to diagrams opposite) and level with a spirit level.
Offer up the radiator to the sleeves to ensure they are in the correct
position. If the radiator is in the correct position, hold the radiator
and mark the position for the bottom brackets.
Remove the radiator and x the two bottom sleeves onto the wall.
Offer up the radiator again and slot the radiator into the bracket
sleeves.
Once the radiator is in the correct position, rmly x the radiator by
tightening the grub screws on the side of the brackets.
Fix Brackets and Hang Radiator
5
Contents
2
Mark Bracket Positions
4
The Radiator Company prides itself on selecting products from
manufacturers who exercise tight quality control measures. We
only select models with excellent standards of welding and
brazing, as well as high quality nishes.
All of our products are well packaged and should reach you
in perfect condition. Just in case however, we offer a minimum
5-year no quibble guarantee for all radiators and towel rails.
The Radiator Company must be notied of
any shortages or damage within 28 days of
delivery. For further information please see
terms and conditions on back page.
Firstly attach the bracket studs to the back of the radiator (shown in
diagram)
The xing positions for the two top brackets are measured at 72mm
down from the top of the collector and measured 17.5mm in from the
side (brackets are positioned on the collector, please see diagram
opposite).
In order to accurately mark the bottom bracket xing positions we
recommend you mark, x and level the two top brackets rst. Then
hang the radiator, ensuring it is vertically level and manually hold the
bottom brackets in position while marking.
PLEASE NOTE :
It is essential that all brackets are level to
ensure a vertical alignment for connecting the
pipe work.
Pipe Centres
Pipe centres left to right
Pipe centres from wall
Depth from wall
Commission
6
Please Note:
In accordance with Part L1 2006 of the Building Regulations and
BS7593:1992 code of practice for the treatment of hot water
and central heating systems, we strongly recommend flushing
the heating system post installation of new radiators and then
adding the correct quantity and type of inhibitor for use with
your radiator and system to prevent corrosion. Damage caused
to systems not protected by a suitable inhibitor will not be
covered by manufacturer’s guarantee.
width - 35mm
63mm - 77mm
102mm - 116mm
1
2
You will need:
• Tape measure
• Electric drill and bits
• Spirit level
Removing Diverter
2
3
Before installation of your BDO 25 the diverter needs to be removed.
To check the position of the diverter, remove the end caps and
look down the collector. You should not be able to see any light if a
diverter is present.
If a diverter is present, using a long screwdriver knock out the
diverter, then securely close the end caps before installation.