THE RADIATOR COMPANY Griffin User manual

Materials Steel
Connections ow and return.
Test pressure 10.5 Bar
Testing authority EN442
Maximum operating pressure 8 Bar
Maximum working temperature 95 ºC
Packaging Cardboard protection with shrink wrap.
1
2
”
The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company notied
within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be tted and The Radiator Company will not accept responsibility
for replacement of scratched or damaged radiators once they have been tted. This includes any
consequential loss or cost of tting.
If The Radiator Company are not notied within 28 days of the date on the signed delivery note then it
will be deemed that The Radiator Company have fully complied with its obligations and claims will not be
considered.
Failure to comply with any of the above may invalidate any claims. We recommend that after you check
the product on delivery that it is stored in its packaging to prevent damage prior to installation. The Radiator
Company cannot accept responsibility for items damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make over to
you the benet of any warranty or guarantee given by the manufacturer, which is usually ve years on most
of our range. (Copies of specic guarantees for any of our products are available on request).
The guarantees in all cases are subject to the products being installed in accordance with British and or
European standards as well as these tting instructions. The guarantees in all cases are restricted to the
free of charge replacement or repair of the failed product only. Our liability will under no circumstances
extend beyond the repair or replacement of the product supplied by us. Claims for either labour in
replacement or damage to property are not admissible. Any goods that are returned, in the event of a
problem, will belong to The Radiator Company.
Technical Specications
Please read these instructions and terms and
conditions carefully prior to installation.
Failure to do so may invalidate the warranty
Griffin
Fittings Instructions
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
THE
RADIATOR
COMPANY
GRIF1.3
PLEASE NOTE:Systemsusingmicroborepipeworkmusthaveadequatepressureandow
rates for the number and style of radiators on the system.

Unpack & Inspect
1
You should have:
• 1 Radiator
• 4 Wall brackets
You will need:
• Tape measure
• Electric drill and bits
• Spirit level
Using a suitable drill bit, screws and plugs,  x the brackets
and level with a spirit level. Please see diagrams opposite on bracket
assembly.
Fix Brackets
4
Contents
2
Mark Bracket Positions
3
Diagrams of Grif n
The Radiator Company prides itself on selecting products from
manufacturers who exercise tight quality control measures. We
only select models with excellent standards of welding and
brazing, as well as high quality  nishes. All of our products are
well packaged and should reach you in perfect condition. Just in
case however, we offer a minimum 5-year no quibble guarantee
for all radiators and towel rails.
The Radiator Company must be noti ed of
any shortages or damage within 28 days of
delivery. For further information please see
terms and conditions on back page.
Firmly  x the brackets to the back of the radiator, and mark the
positions for the bracket sleeves on the wall. The  xing positions for
the two top brackets are measured at 25mm in from either end and
measured down 90mm from the top (please see diagram opposite).
Loosely  x the sleeves to the wall and hold up the radiator to check
the positions. Once they are correct, put down the radiator, secure
the sleeves to the wall, and then hold up the radiator once again and
secure onto the sleeves by tightening the grub screws.
In order to accurately mark the bottom bracket  xing positions we
recommend you mark,  x and level the two top brackets  rst. Then
hang the radiator, ensuring it is vertically level and manually hold the
bottom brackets in position while marking.
PLEASE NOTE :
It is essential that all brackets are level to
ensure a vertical alignment for connecting the
pipe work.
Pipe Centres
Pipe centres left to right
Pipe centres from wall
Depth from wall
Commission
5
Please Note:
In accordance with Part L1 2006 of the Building Regulations and
BS7593:1992 code of practice for the treatment of hot water
and central heating systems, we strongly recommend flushing
the heating system post installation of new radiators and then
adding the correct quantity and type of inhibitor for use with
your radiator and system to prevent corrosion. Damage caused
to systems not protected by a suitable inhibitor will not be
covered by manufacturer’s guarantee.
width - 43mm
60mm - 68mm
77mm - 85mm
Bracket Assembly
90
90
25
25