THE RADIATOR COMPANY Ovali Bath User manual

Materials Aluminium
Connections ow and return.
Test pressure 9 Bar
Testing authority EN442
Maximum operating pressure 6 Bar
Maximum working temperature 90 ºC
Packaging Polystyrene Protection in cardboard box
1
2
”
The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company
notified within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be fitted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been fitted.
This includes any consequential loss or cost of fitting.
If The Radiator Company are not notified within 28 days of the date on the signed delivery
note then it will be deemed that The Radiator Company have fully complied with its
obligations and claims will not be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging
to prevent damage prior to installation. The Radiator Company cannot accept responsibility
for items damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make
over to you the benet of any warranty or guarantee given by the manufacturer, which is usually
ve years on most of our range. (Copies of specic guarantees for any of our products are
available on request).
The guarantees in all cases are subject to the products being installed in accordance with British
and or European standards as well as these tting instructions. The guarantees in all cases are
restricted to the free of charge replacement or repair of the failed product only. Our liability will
under no circumstances extend beyond the repair or replacement of the product supplied by us.
Claims for either labour in replacement or damage to property are not admissible. Any goods
that are returned, in the event of a problem, will belong to The Radiator Company.
Technical Specications
Please read these instructions and terms and conditions
carefully prior to installation. Failure to do so may
invalidate the warranty
Ovali Bath
Fittings Instructions
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
If you have any questions please contact us on 01342 302250
www.theradiatorcompany.co.uk
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
THE
RADIATOR
COMPANY
GRDOB1.2
PLEASE NOTE: To reduce the possibility of noise caused by rapid heating and cooling
of aluminium radiators; adequate capacity for expansion must be provided within
the overall heating system. Systems using micro bore pipework must have adequate
pressure and flow rates for the number and style of radiators on the system.

Unpack & Inspect
1
You should have:
• 1 Radiator
• 1 Airvent (pre-tted)
• 1 Blanking Plug (pre-tted)
• 1 Diverter (pre-tted)
• 4 Bracket Caps (D)
• 4 Bracket Screws (C)
• 4 Brackets (B)
• 4 Support Plates (A)
• 8 Wall Plugs and Screws
Contents
2
Mark and Fix Brackets
3
Diagrams of Ovali Bath
The Radiator Company prides itself on selecting products from
manufacturers who exercise tight quality control measures. We only
select models with excellent standards of welding and brazing, as well
as high quality nishes. All of our products are well packaged and
should reach you in perfect condition. Just in case however, we offer
a minimum 5-year no quibble guarantee for all
radiators and towel rails.
The Radiator Company must be notied of any
shortages or damage within 28 days of delivery.
For further information please see terms and
conditions on back page.
1. The airvent, blanking plug and
diverter are all already tted on the
radiator.
PLEASE NOTE :
It is essential that all brackets are level to ensure a
vertical alignment for connecting the pipework.
Pipe Centres
Pipe centres left to right
Pipe centres from wall
Depth from wall
Commission
4
Please Note:
In accordance with Part L1 2006 of the Building Regulations and
BS7593:1992 code of practice for the treatment of hot water and
central heating systems, we strongly recommend flushing the heating
system post installation of new radiators and then adding the correct
quantity and type of inhibitor for use with your radiator and system
to prevent corrosion. Damage caused to systems not protected by
a suitable inhibitor will not be covered by manufacturer’s guarantee.
Width + Valves
43mm
200mm
59
52
43
2. Accurately mark bracket holes on the wall using a tape measure
and spirit level. (Height of the radiator from oor : minimum 100mm)
3. Drill 8mm diameter holes to a minimum depth of 50 mm,
and insert suitable wall plugs.
4. Place the support plates “A” on the wall in line with the wall plugs
and secure using suitable screws.
5. Insert the brackets “B” into the support plates “A”, and secure
and level with screws “C”. Fit the bracket closing cap “D” on top.
6. Hang the radiator on the rst space of the brackets (please see
diagram above) and ensure the radiator is level using a spirit level.
Please refer to diagrams opposite when
following steps below:
You will need:
• Tape measure
• Electric drill and bits
• Spirit level
• Flathead screwdriver
• Crosshead screwdriver
Please Note: The wall plugs and screws supplied will not be
suitable for all wall types. Please ensure suitable wall plugs and
screws are used.
200
43
G
A
B
C
D