THE RADIATOR COMPANY Echo User manual

Materials Steel
Connections ow and return.
Test pressure 7.8 Bar
Testing authority EN442
Maximum operating pressure 6 Bar
Maximum working temperature 95 ºC
Packaging Wrapped in polythene in cardboard box
1
2
”
The Radiator Company
Units 13 - 14 Charlwoods Road
East Grinstead
West Sussex
RH19 2HU
All products must be inspected once removed from the packaging and The Radiator Company
notied within 28 days of delivery of any scratches, blemishes or other damage.
The Radiator Company will then replace the radiator.
Imperfect radiators should therefore not be tted and The Radiator Company will not accept
responsibility for replacement of scratched or damaged radiators once they have been tted. This
includes any consequential loss or cost of tting.
If The Radiator Company are not notied within 28 days of the date on the signed delivery note then
it will be deemed that The Radiator Company have fully complied with its obligations and claims will
not be considered.
Failure to comply with any of the above may invalidate any claims.
We recommend that after you check the product on delivery that it is stored in its packaging to
prevent damage prior to installation. The Radiator Company cannot accept responsibility for items
damaged after delivery.
Terms & Conditions
Guarantees & Liabilities
As we are not the manufacturers of this product we will take all reasonable endeavours to make
over to you the benet of any warranty or guarantee given by the manufacturer, which is usually ve
years on most of our range. (Copies of specic guarantees for any of our products are available on
request).
The guarantees in all cases are subject to the products being installed in accordance with British and
or European standards as well as these tting instructions. The guarantees in all cases are restricted
to the free of charge replacement or repair of the failed product only. Our liability will under no
circumstances extend beyond the repair or replacement of the product supplied by us. Claims
for either labour in replacement or damage to property are not admissible. Any goods that are
returned, in the event of a problem, will belong to The Radiator Company.
Technical Specications
Please read these instructions and terms and conditons
carefully prior to installation.
Failure to do so may invalidate the warranty
Echo
Fittings Instructions
5
Y
e
a
r
G
u
a
r
a
n
t
e
e
Y
e
a
r
G
u
a
r
a
n
t
e
e
THE
RADIATOR
COMPANY
ECHO_IR_1.0
PLEASE NOTE:Systemsusingmicroborepipeworkmusthaveadequatepressureandow
rates for the number and style of radiators on the system.
If you have any questions please contact us: 01342 302250, www.theradiatorcompany.co.uk A brand of , Italy’s leading manufacturer of design led radiators

Unpack & Inspect
1
You should have:
• 1 Radiator
• 2 Wall bracket sleeves
• 1 Airvent
• 1 Blanking Plug
You will need:
• Tape measure
• Electric drill and bits
• Spirit level
Using a suitable drill bit, screws and plugs, x the brackets sleeves to
the wall and level with a spirit level. Please see diagrams.
Fix Brackets
4
Contents
2
Mark Bracket Positions
3
Diagrams of Echo
The Radiator Company prides itself on selecting products from
manufacturers who exercise tight quality control measures.
We only select models with excellent standards of welding and
brazing, as well as high quality nishes.
All of our products are well packaged and should reach you in
perfect condition. Just in case however, we offer a minimum
5-year no quibble guarantee for all radiators and towel rails.
Please carefully unpack and inspect this radiator and all ttings.
The Radiator Company must be notied of any shortages or
damage within 28 days of delivery.
For further information please see terms
and conditions on back page.
The fixing positions for the two top brackets are measured at
100mm down from the top of the collector and 100mm up from
the bottom of the collector (please see diagram opposite).
In order to accurately mark the bottom bracket fixing positions
we recommend you mark, fix and level the two top brackets first.
Then hang the radiator, ensuring it is vertically level and manually
hold the bottom brackets in position while marking.
PLEASE NOTE :
It is essential that all brackets are level to
ensure a vertical alignment for connecting the
pipework.
Pipe Centres
Pipe centres left to right
Pipe centres from wall
Depth from wall
50mm
57mm - 65mm
112mm - 120mm
Hang Radiator & Commission
5
With the brackets sleeves rmly xed and level, slot the radiator into
the sleeves and rmly x by tightening the grub screws.
When securing the brackets, we suggest positioning the sleves in a
way which the top bracket’s gurb screw is facing upwards, and the
bottom bracket’s grub screw is facing down. This will improve the
aesthetics of the raditor and avoid any screws being seen.
Please Note:
In accordance with Part L1 2006 of the Building Regulations and
BS7593:1992 code of practice for the treatment of hot water
and central heating systems, we strongly recommend flushing
the heating system post installation of new radiators and then
adding the correct quantity and type of inhibitor for use with
your radiator and system to prevent corrosion. Damage caused
to systems not protected by a suitable inhibitor will not be
covered by manufacturer’s guarantee.
100
100
Can be installed as a left- or right-handed version
Bracket Positions